using simple logic gates Design Problem A Chemical plant needs a microprocessor-driven alarm system to warn of critical conditions in one of its chemical tanks. The tank has four (HIGH / LOW) switches that monitor: Temperature (T) Pressure (P) Fluid Level (L) Weight (W) Design a system that will notify the microprocessor to activate an alarm when any of the following conditions arise: High Fluid Level with High Temperature and High Pressure Low Fluid Level with High Temperature and High Weight Low Fluid Level with Low Temperature and High Pressure Low Fluid Level with High Temperature and Low Weight

using simple logic gates Design Problem A Chemical plant needs a microprocessor-driven alarm system to warn of critical conditions in one of its chemical tanks. The tank has four (HIGH / LOW) switches that monitor: Temperature (T) Pressure (P) Fluid Level (L) Weight (W) Design a system that will notify the microprocessor to activate an alarm when any of the following conditions arise: High Fluid Level with High Temperature and High Pressure Low Fluid Level with High Temperature and High Weight Low Fluid Level with Low Temperature and High Pressure Low Fluid Level with High Temperature and Low Weight

Electric Motor Control

10th Edition

ISBN:9781133702818

Author:Herman

Publisher:Herman

Chapter22: Sequence Control

Section: Chapter Questions

Problem 6SQ: Draw a symbol for a solid-state logic element AND.

See similar textbooks

Similar questions

Using Simple Logic Gates. Given: A Chemical plant needs a microprocessor-driven alarm system to warn of critical conditions in one of its chemical tanks. The tank has four (HIGH / LOW) switches that monitor: Temperature (T) Pressure (P) Fluid Level (L) Weight (W) To Find: Design a system that will notify the microprocessor to activate an alarm when any of the following conditions arise: High Fluid Level with High Temperature and High Pressure Low Fluid Level with High Temperature and High Weight Low Fluid Level with Low Temperature and High Pressure Low Fluid Level with High Temperature and Low Weight Note: Construct Truth Table. Draw Logic Diagram. Simplify Boolean equations using K-Map. Use Basic Logic Gates.
) A new manufacturing plant which operates on parameters such as temperature and pressure, has been procured by your company. In the operational manual is stated “if one or more than one parameter exceeds the safe value, a protective measure is needed to be done”. As an engineer, design a schematic diagram using an OR gate to detect the exceed parameter and explain how it will produce a command signal for the system to take the required action. Major Topic 12 Basic logic gates & its application AN
Assume a three-story hospital is built at Expo Center Karachi, and you are hired to design the logic circuit for the newly installed lift. The lift only stops at Ground, Second, Third Floors. The lift has one button (RUN), that can be turned into Up or Down position. When the switch is turned to the UP position (i.e. R=1), the lift goes upward from the Ground floor (i.e. 0) to the top floor (i.e. 3), and if the switch is turned to the DOWN position (i.e. R=0) it will go downward. Design this synchronous sequential circuit for this up-down counter using the JK-flip- flops. Perform all design steps, including state-diagram, state-table, K-map, minimized expressions and finally, the draw the logic circuit.
There are 5 gates in a metrobus, 1 of which is to get on and 4 to get off. The number of passengers inside is desired to be seen on the LCD connected to the P2 port. Get-on gate is controlled by the P0.2 while get-off gates are controlled by the P0.3, P0.4, P0.5, and P0.6. The sensors generate Logic-1 while passing passengers. Since the passenger carrying capacity of the metrobus is 294, if the number of passengers exceeds the number of 294, the warning LED connected to the P0.7 pin is required to light up. Since other pins of P0 are used for other purposes, it is not desired to be changed. Can you write the answer with assembly code using 8051 - AT89S8253 architecture?
Topic: Digital Electronics Please explain better while solving so I can please understand very well. QUESTION: Explain race around condition using a suitable logic diagram? How it can be avoided?
(2) Design synchronous mod 5 counter State table, K-map, boolean equations, and logic circuit. (coding not needed) (Please do not write by hand.)
Create a schematic diagram and Truth Table for a logic circuit that is made up entirely of NAND gates of the given below:The scenario involves a circuit that has an alarm system, which activates a buzzer whenever both the power and at least one of the two sensors are turned on. It is important to note that the sensors will only function if an enable pin is activated.
A limited company has four directors A, B, C, D holding 35%, 30%, 20% and 15% of the shares respectively. A major decision must have a support of minimum 60% of the stock. Design a combinational logic circuit for the voting in the company. Use a decoder to design the circuit. Show the truth table of the circuit.
A manufacturing plant needs to have a horn sound to signal quitting time. The horn should beactivated when either of the following conditions is met:1. It’s after 5 o’clock and all machines are shut down.2. It’s Friday, the production run for the day is complete, and all machines are shutdown.Design a logic circuit that will control the horn. (Hint: Use four logic input variables torepresent the various conditions; for example; input A will be HIGH only when the time of day is 5o’clock or later)
Q: Design an electronic system that represents some scenario created by you? (simple one that contains AND OR And NOT gates. ) Write a Boolean equation for it Design a circuit for it explain what your Scenario represents?
A MIG 31 fighter jet has a monitoring system for rpm, pressure and temperature The engine uses several sensors that operate as follows: RPM (R), sensor output = 0 if speed < 10,000 rpm Pressure (P), sensor output = 0 if pressure < 220 psi Temperature (T), sensor output = 0 if temperature < 200 oF The following figure is the logic circuit that controls the warning lights in the cockpit of the aircraft for variations in certain engine conditions. Assume the HIGH condition will make the light turn on. Using the truth table, determine under what condition the engine lights warning will flash 2. Modify the circuit using all NAND gates *Please solve number 2
a) Design a logic circuit with three inputs A, B, C and an output that goes LOW only when A is HIGH while B and C are different. Draw and upload the circuit if you can, or at least describe it in words. b) Which logic gates produce a 1 output in the disabled state? c) Which logic gates pass the inverse of the input signal when these gates are enabled? d) What is the normal resting state of the SET’ and RESET’ inputs of a latch circuit (the prime is same as bar)? What is the active state of each input? e) What is the normal resting state of the NOR latch inputs? What is the active state?