2. A horizontal jet of water having a velocity of 25 m/s, diameter=2 cm strikes an inclined straight blade moving in the direction opposite to the direction of jet with a velocity of 10 m/s. If the inclination of the blade is 15° with the horizontal, the force developed on the blade per kg of water per second in the direction of the flow will be:

2. A horizontal jet of water having a velocity of 25 m/s, diameter=2 cm strikes an inclined straight blade moving in the direction opposite to the direction of jet with a velocity of 10 m/s. If the inclination of the blade is 15° with the horizontal, the force developed on the blade per kg of water per second in the direction of the flow will be:

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

1) Interpret solar power in the context of environmental impact.2. What is the rigid dichotomy between windmill and diesel-driven pumps?3. For a normal windmill-driven pump at 3 m/s wind speed, the yield at a 10 m Head is typically 0.12 liters/s per m2 of rotor area, value windmills in the context of yield.
A fluid moves in a steady flow manner between two sections in a flow line. At the entrance section: A1, -1 m2, V = 0.5 m/s, P1 = 4 kg/m2. At the exit section: Az =0.2 m2, v 2 = 0.20 m®/kgm. Calculate (a) the mass flow rate in kg/s and (b) the speed at section 2 in m/s.
A reducing elbow is used to deflect water flowrate at a rate of 1920 g/s in a horizontal pipe downward by an angle theta = 43 from the flow of direction while accelerating it. The elbow discharges water into the atmosphere. The diameter of the elbow at the inlet is 6.5 cm and at the exit is 1.5cm. The elevation difference between the centers of the exit and the inlet is 22cm . The mass of the elbow and the water is 61.5 kg. Determine the anchoring force needed to hold the elbow in place
A centrifugal blower rotates at 1400 rpm. Air enters the impeller normal to the blades (?1 = 0°) and exits at an angle of 25° (?2 = 25°). The inlet radius is r1 = 6.5 cm, and the inlet blade width b1 = 8.5 cm. The outlet radius and blade width are r2 = 12 cm and b2 = 4.5 cm, respectively. The volume flow rate is 0.22 m3 /s. What is the net head produced by this blower in meters of air? (a) 12.3 m (b) 3.9 m (c) 8.8 m (d) 5.4 m (e) 16.4 m
A jet of water of diameter 60 mm strikes a stationary flat plate normally at a velocity of 26 m/s. What is the force exerted by the jet of water? Select one: a. 1,911.3 N b. 1,756.4 N c. 1,561.6 N d. 1,722.1 N
A lawn sprinkler with three identical arms is used to water a garden by rotating in a horizontal plane by the impulse caused by water flow. Water enters the sprinkler along the axis of rotation at a rate of 45 L/s and leaves the 1.5-cm-diameter nozzles in the tangential direction. The bearing applies a retarding torque of T0 = 40 N·m due to friction at the anticipated operating speeds. For a normal distance of 40 cm between the axis of rotation and the center of the nozzles, determine the angular velocity of the sprinkler shaft.
A Francis radial-flow hydroturbine has the following dimensions, where location 2 is the inlet and location 1 is the outlet: r2 = 6.60 ft, r1 = 4.40 ft, b2 = 2.60 ft, and b1 = 7.20 ft. The runner blade angles are ?2 = 82° and ?1 = 46° at the turbine inlet and outlet, respectively. The runner rotates at n. = 120 rpm. The volume flow rate at design conditions is 4.70 ×106 gpm. Irreversible losses are neglected in this preliminary analysis. Calculate the angle ?2 through which the wicket gates should turn the flow, where ?2 is measured from the radial direction at the runner inlet. Calculate the swirl angle ?1, where ?1 is measured from the radial direction at the runner outlet. Does this turbine have forward or reverse swirl? Predict the power output (hp) and required net head (ft).
A jet of water with velocity 35 m/s strikes a series of radial curved vane mounted on a wheel which is rotating at 200 rpm. The jet makes an angle 30° with the tangent to the wheel at inlet, and leaves the wheel with a velocity 5 m/s at angle of 140° to the tangent to the wheel at the outlet. The outer and inner radii of the wheel are 70 cm and 35 cm, respectively. A. Determine the Inlet Vane Angle, in degrees. B. Determine the Outlet Vane Angle, in degrees. C. Determine the work done per unit weight of water, in Newton-Meter per Newton.
Express the unsteady angular momentum equation in vector form for a control volume that has a constant moment of inertia I, no external moments applied, one outgoing uniform flow stream of velocity V→, and mass flow rate m. .
A jet of water with velocity 35 m/s strikes a series of radial curved vane mounted on a wheel which is rotating at 200 rpm. The jet makes an angle 30° with the tangent to the wheel at inlet, and leaves the wheel with a velocity 5 m/s at angle of 140° to the tangent to the wheel at the outlet. The outer and inner radii of the wheel are 70 cm and 35 cm, respectively. Determine the work done per unit weight of water, in Newton-Meter per Newton.
Between two sections in a vessel, a fluid moves in a steady flow manner. At entrance: A1=20 m2, ρ1=1300 kgm/m3. At exit: A2=10 m2, ʋ2=0.00125 m3/kg, ῡ2=3 m/min. Determine the following: a) ḿ1 in kg/min b) ῡ1 in m/min
A jet of water with velocity 35 m/s strikes a series of radial curved vane mounted on a wheel which is rotating at 200 rpm. The jet makes an angle 30° with the tangent to the wheel at inlet, and leaves the wheel with a velocity 5 m/s at angle of 140° to the tangent to the wheel at the outlet. The outer and inner radii of the wheel are 70 cm and 35 cm, respectively. A. Determine the Inlet Vane Angle, in degrees.