A lawn sprinkler with three identical arms is used to water a garden by rotating in a horizontal plane by the impulse caused by water flow. Water enters the sprinkler along the axis of rotation at a rate of 45 L/s and leaves the 1.5-cm-diameter nozzles in the tangential direction. The bearing applies a retarding torque of T0 = 40 N·m due to friction at the anticipated operating speeds. For a normal distance of 40 cm between the axis of rotation and the center of the nozzles, determine the angular velocity of the sprinkler shaft.

Q: Water, issuing vertically from a nozzle having a diameter of 25 mm, flows out under a head of 30 m.…

A:

Q: Water at 65 degrees Celsius is flowing horizontally at a rate of 84.1 m^3/hr in a pipe. It enters a…

A:

Q: Q1:Air enters a diffuser at 200 m/s with a pressure of 80 kPa and a temperature of -20°C. It leaves…

A:

Q: A cylindrical tank is being filled with water flowing with constant velocity V1 through a tap (Tap…

A: Given, Diameter of the tap  1= d1 Velocity through the tap = V1 Diameter of the tank = DT. Diameter…

Q: Water flowing steadily at a rate of 0.16 m3/s is deflected downward by an angled elbow as shown. For…

A: The point 2 is taken as reference point as shown in figure below :

Q: Commercially available large wind turbines have blade span diameters larger than 100 m and generate…

A: Given data: Blade span diameter, d = 75 m Radius of blade, r = 37.5 m Wind velocity, v = 25 km/h =…

Q: The rectangular duct section of 400mm*300mm size carries 50 m^3/min of air, with density 1.2 kg/m^3.…

A: Question part (A) is Solved here. For Other part of Question, Please post this question again.

Q: Water is coming out to the atmosphere from a converging channel with a velocity of 5 m/s as shown in…

A:

Q: A 3 in diameter horizontal water jet having a velocity of 140 ft/s strikes a curved plate, which…

A:

Q: Q3: (A) A Pelton wheel has a bucket speed (u) of 12 m/s and is supplied with water at a rate of 0.68…

A: Note Question (A) is Solved here. For Question (B), Please post this Question again.

Q: Water enters a centrifugal pump axially at atmos- pheric pressure at a rate of 0.12 m3/s and at a…

A:

Q: Exhaust gas from a tailless helicopter turbojet engine flows through the three 0.95-ft-diameter…

A: Given data: d=0.95 ftQ=480 ft3/s Need to determine the angular velocity of the rotor.

Q: Water @ 30C and 1atm is flows at a rate of 0.5 m^3/s through a horizontal junction in a pipe. The…

A: To find: The resultant force on the junction. Given: The flow rate is Q=0.5 m3sec. The internal…

Q: A reducing elbow is used to deflect water flow at a rate of 0.02 m³/s in a horizontal pipe upward…

A:

Q: A 7-cm diameter vertical water jet is injected upwards by a nozzle at a speed of 15 m/s. Determine…

A: Given: The diameter of the vertical water jet is D=7 cm. The velocity of the water jet is U=15 m/s.…

Q: Water is flowing through a 15-cm-diameter pipe that consists of a 3-m-long vertical and 2-m-long…

A: Given Data: The diameter of pipe is d = 15 cm. Velocity of water leaving is v = 5 m/s. The mass of…

Q: A 180 m of rubber cotton lined hose having a diameter of 75 mm is attached to a hydrant at which the…

A: Given: Pressure P1=410kPaFriction factor f=0.024Diameter of the hose D=0.075mDensity of water…

Q: Air enters into the hollow propeller tube at A with a mass flow of 3.5 kg/s and exits at the ends B…

A:

Q: Determine the magnitude and direction of the resultant force exerted on this double nozzle by water…

A: force a force is any influence that, when unopposed, will change the motion of an object. A force…

Q: Air enters an open system with a velocity of 5 m/s and a density of 1 kg/m at 600 K through a pipe…

A: Velocity = 5 m/s density = 1 kg/m3 Temperature = 600 K Area = 10 cm2

Q: Water enters a mixed flow pump axially at a rate of 0.25 m3/s and at a velocity of 5 m/s, and is…

A: flow rate, Q = 0.25 m3/s     velocity,V= 5 m/s           angle = 75° Calculate force acting on the…

Q: A horizontal water jet impinges against a vertical flat plate at 30 ft/s and splashes off the sides…

A: Given: The velocity of the water is V=30 ft/s. The force to hold the plate is F=500 lbf.

Q: A simple pitot tube and a piezometer are installed in a vertical pipe as shown in the figure. If…

A:

Q: A reducing elbow is used to deflect water flowrate at a rate of 1920 g/s in a horizontal pipe…

A: mass flow rate m˙=1920g/s =1.92kg/shorizontal pipe downward by an angle, θ = 43o diameter of the…

Q: n this situation, a 90 degree elbow pipe is used to direct water flow in an upwards direction, at a…

A:

Q: Determine (a) the gage pressure at the center of the inlet of the elbow and (b) the anchoring force…

A:

Q: If the diameter at section 1 is d1 = 52 cm and at section 2 d2=81 cm and the mean velocity at…

A: Given: d1=52 cmd2=81 cmv2=2.2 m/s

Q: The rectangular duct section of 400mm*300mm size carries 50 m^3/min of air, with density 1.2 kg/m^3.…

A:

Q: A hydroelectric power plant uses Pelton-type turbines, in which multiple nozzles are used to…

A: Given data:

Q: Water enters a centrifugal pump axially at atmospheric pressure at a rate of 0.09 m3/s and at a…

A: Given: The rate of the water enters the centrifugal pump is Q=0.09 m3/s. The velocity of the water…

Q: A 7-cm diameter vertical water jet is injected upwards by a nozzle at a speed of 15 m/s. Determine…

A: GIVEN:d=7cmu=15m/s

Q: A Pelton wheel has a diameter of 2 m and develops 500 kW when rotating 180 rpm. What is the average…

A: Givenpelton wheel turbined=2mP=500kWN=180rpmoperating at maximum efficiency

Q: Water flowing steadily at a rate of 0.16 m3/s is deflected downward by an angled elbow as shown. For…

A: Consider the following control volume. Let Fx and Fy be the forces by the flange on the control…

Q: A 4-cm-diameter horizontal stationary water jet having a velocity of 50 m/s strikes a cone having in…

A:

Q: Water enters a centrifugal pump axially at atmospheric pressure at a rate of 0.10 m3/s and at a…

A: Given data as per question Rate of water entering = 0.10 m3/s Velocity = 6 m/s Density of water =…

Q: Determine the magnitude and direction of the resultant force exerted on this double nozzle by water…

A: Fluid Mechanics: It is a branch of physics in which concerns with mechanics of fluids & forces…

Q: In a community event, a game of 'water resistance' is played by a group of people. Considering a…

A:

Q: A garden hose attached with a nozzle is used to fill a 20 Liters bucket. The inner diameter of the…

A:

Q: A reducing elbow in a horizontal pipe is used to deflect water flow by an angle 0 = 56° from the…

A:

Q: 19- Considering the incompressible, frictionless flow of water in a vertical pipe, the pressure is…

A:

Q: A 7-cm diameter vertical water jet is injected upwards by a nozzle at a speed of 15 m/s. Determine…

A:

Q: While travelling on a dirt road, the bottom of a car hits a sharp rock and a small hole develops at…

A: Find the initial velocity of the petrol at the  hole.

Q: Determine the stopping temperature and stopping pressure for the following substances and flow…

A: (A) Given Data Temperature of helium is : T=50°C Pressure of helium is : P=0.15 MPa Velocity of…

Q: A 9-cm-diameter horizontal water jet strikes a curved plate, which deflects the water 180° at the…

A: For solution refer below images.

Q: Water at 75 degrees Celsius is flowing horizontally at a rate of 1.6 m^3/min in a pipe. It enters a…

A:

Q: a) If it takes 2.35 min to fill a 20.5 L bucket with water flowing from a garden hose of diameter…

A:

Q: A water jet strikes a moving plate at velocity of 10 m/s as the plate moves at a velocity of 2 m/s.…

A:

Q: 3. Water is flowing through a 15 cm diameter pipe that consists of a 3 m long vertical and 2 m long…

A:

Applied Fluid Mechanics

A fluid is a substance that is continuously deformed by the application of shear stress. The rate of deformation of a fluid depends on its viscosity. The fluid tries to flow when it interacts with some other system.