2. A liquid flows through an orifice located in the side of a tank as shown in the Figure below. A commonly used equation for determining the volume rate of flow, Q, through the orifice is Q = 0.61A/2gh where A is the area of the orifice, g is the acceleration of gravity, and h is the height of the liquid above the orifice. Investigate the dimensional homogeneity of this

2. A liquid flows through an orifice located in the side of a tank as shown in the Figure below. A commonly used equation for determining the volume rate of flow, Q, through the orifice is Q = 0.61A/2gh where A is the area of the orifice, g is the acceleration of gravity, and h is the height of the liquid above the orifice. Investigate the dimensional homogeneity of this

Engineering Fundamentals: An Introduction to Engineering (MindTap Course List)

5th Edition

ISBN:9781305084766

Author:Saeed Moaveni

Publisher:Saeed Moaveni

Chapter6: Fundamental Dimensions And Units

Section: Chapter Questions

Problem 49P

See similar textbooks

Similar questions

Kim Jisoo discovered an element (1.43 kN/m3) that flows through a 100 mm (diameter) pipe at a mean velocity of 3 m/s. Find the volume flow rate in L/s. Round off to one decimal place.
I need to determine the length in meters of ? in the diagram, so that each time, at least 1 quarter of the black rectangle is immersed in the red liquid in the blue container (the immersion area shown in pink outline). I will be flipping the black rectangle 4 times, to cover as much of the black rectangle's area as possible. The red liquid is 0.5m deep, and the blue container is 0.7m high. The black rectangle rests on the top edge of the blue container. See diagram.
Fluid Mechanics question: A device used for measuring the specific weight of a liquid consists of a u-tube manometer as shown. The manometer tube has an internal diameter of 0.5 cm and originally has water in it. Exactly 2 cm3 of unknown liquid is poured into one leg of the manometer, and a displacement of 5cm is measured between the surfaces as shown. What is the specific weight of the unknown liquid?
Q1: Given the following quantities Q= discharge, ∆? ? = pressure drop per unit length, ?= viscosity, D= diameter Use Buckingham theorem to find an expression relates Q with the other quantities.
Pitot tube is an instrument that is used to measure flowrate in a pipe. Figure 3 shows water flowing through a pipe with pitot tube attached to a U-tube manometer containing Fluid X. Given the difference in height in the manometer, h, calculate the flowrate through the pipe by showing the application of Bernoulli Equation and Hydrostatic Pressure Equation. Details of the parameters are as follows; Difference in manometer, h = 0.1 m Density of water = 1000 kg/m3 Density of Fluid X = 12000 kg/m3 Diameter of pipe = 0.3m
For the figure ,point A is (30 cm) below the surface of liquid , What is the pressure. * a_17.658 kpa b_17.658 kpa (vacume) c_176.58 kpa d_Option 4
The image is for number 1 1. Referring to the figure, a cylindrical column of height equals 5 800 cm has a 115 cm radius. It contains blood with a density equal to 1.06 g/cc. Find the force exerted by the air on the disk of radius 115 cm at the surface of the blood. 425 kN 420 kN 415 kN 435 kN 430 kN 410 kN What pressure at a depth of 5 800 cm supports the blood column? 704 kPa 604 kPa 904 kPa 504 kPa 404 kPa 804 kPa
A closed pressurized tank shown below is filled with oil and mercury. Mercury is confined in an internal reservoir inside the closed tank, the height of mercury is 450mm. An open manometer is placed on the bottom left part of the tank with liquid “X” as its gage liquid , the deflection from the gage liquid shows 800mm. Determine the following:a) Height of the oil from point A up to point c if height A to C is 5 times the height of y. b) Pressure @ point B in kPa. c) Pressure @ point C in psi.
In figure 6, compute the pressure difference between m and n, in pounds per square inch, when: (a) Fluid A is brine (sp gr 1.15), the gage fluid is oil (sp gr 0.92), and z = 45.15 in. (b) Fluid A is water, the gage fluid is air, and z = 15.15 in.
The liquid reservoir in the figure accelerates to the right with its fluid moving like a rigid solid. Determine the modulus of the horizontal acceleration. Consider the fluid to be glycerin at 20 ° C, whose specific gravity is 1.263.
A cylinder falls down the inside of an oil-filled pipe as shown. The small space between the pipe and cylinder is lubricated with a film of oil with a viscosity mu. Derive a formula for the steady state rate of descent of the cylinder with weight, W, diameter, d, and length, l, slinding inside the vertical smooth pipe with diameter, D. Assume the cylinder is concentric with the pipe as it falls. Use the general formula to find the rate of descent of a cylinder 100mm in diameter that slides inside a 100.5mm inside diameter pipe. The cylinder is 200mm long and weights 15N. The lubricant is SAE 20W oil at 10oC.
Calculate the capillary effect in millimeters in a glass tube of 4mm diameter, when immersed in Water Mercury the temperature of the liquid is 200C in contact with air are 0.073575 N/m and 0.51 N/m respectively. The angle of contact for water is zero and that for mercury is 1300. Take density of water at 200C as equal to 998 kg/m3. Explain the ways of describing the fluid motion