Q 1, 2, 5, 6, 8, 12: Experimentally, the drag force Fp due a square cylinder located ina laboratory flume is influenced by cylinder width b, cylinder height z, fluid viscosityH, mass density p, and flow velocity u as related in the following:F f (0 ,z, μ. ρ, υ)Use Buckingham's theorem to find dimensionless terms.

Here in the solution i have denoted cylinder height with L and cylinder width with W

Q 1, 2, 5, 6, 8, 12: Experimentally, the drag force Fp due a square cylinder located in a laboratory flume is influenced by cylinder width b, cylinder height z, fluid viscosity µ, mass density p, and flow velocity u as related in the following: F f (0, z, μ. ρ, υ) Use Buckingham's theorem to find dimensionless terms.

Q 1, 2, 5, 6, 8, 12: Experimentally, the drag force Fp due a square cylinder located in a laboratory flume is influenced by cylinder width b, cylinder height z, fluid viscosity µ, mass density p, and flow velocity u as related in the following: F f (0, z, μ. ρ, υ) Use Buckingham's theorem to find dimensionless terms.

Engineering Fundamentals: An Introduction to Engineering (MindTap Course List)

5th Edition

ISBN:9781305084766

Author:Saeed Moaveni

Publisher:Saeed Moaveni

Chapter6: Fundamental Dimensions And Units

Section: Chapter Questions

Problem 49P

See similar textbooks

Similar questions

Bernoulli’s equation and represents the sum of velocity head, pressure head and the elevation head above: a. the bottom of the pipe. b. the arbitrary horizontal datum c. the center line of pipe d. the top of the pipeline
Given the acceleration-time diagram sketch the velocity-time diagram and determine the displacement at time=9s.
Limitations on the Use of the Bernoulli Equation A two dimensional flow field is given by u=2y, v=x. (a) sketch the flow field. (b)Derive a general expression for the velocity and acceleration(x and y are in units of length L; u and v are in units of L/T). (c) Find the acceleration in the flow field at point A (x=3.5, y=1.2).
Find the relation between Bernoulli’s equation and the Darcy's law in one dimensional fluid flow.
In the accompanying diagram, spring A is a linear spring and spring B is a hard spring, with characteristics that are described by the relationship F = kxn . Determine the stiffness coefficient k for each spring. What is the exponent n for the hard spring? In your own words, also explain the relationship between the spring force and the deflection for the hard spring and how it differs from the behavior of the linear spring.
A manometer is used to measure the pressure difference between points A and B in a pipe as shown. Water flows in the pipe, and the specific gravity of the manometer fluid is 3.0. The distances and manometer deflection are indicated on the figure. Find (a) the pressure differences and (b) the difference in Piezometric Pressure, (c) the difference in Piezometric head. Express both answers in kPa.
The flow of an incompressible fluid in cylindrical coordinates is given by Find ur if ur = 0 at r = 2 for all θ. The flow does not depend on z.
in the system shown, determine the value of the force f if the coefficient of friction between the body and floor is 0.41. P is 264.87N
Q1: The volume flow rate (Q) over a rectangular duct depends on the head H over the duct, acceleration due to gravity g. length of duct L, height of the duct Z and the kinematic viscosity v of the liquid. (1) Derive the relationship between the above variables and the volume flow rate by using Buckingham's II-theorem. (2) Explain the physical meaning of the obtained dimensionless groups.
Q. A block of 150 N is placed on the surface having coefficient of friction 0.4 (shown in figure). What force is required to just enable the block to move. Consider two cases related to force (a) Pushing force (b) Pulling force
Fluid often passes through pores in cell membranes or cell layers. The dimensions are small and the velocities low, so viscous forces dominate (low Reynolds number). Use dimensional analysis, or an approximate method of analysis based on the viscous flow equations, to determine the scaling law that expresses the dependence of the pressure drop across a pore (ΔP) on the flow rate through it (Q). The other parameters that are given include the pore radius, R, and the viscosity of the fluid, μ. The membrane itself should be considered infinitesimally thin so that its thickness does not influence the pressure drop.
From the figure below, determine reaction Av. Use absolute value. (No need to include sign since absolute values are always positive). *