2. A rope helps to support a uniform 800-N beam 7 m long the lower end of which is hinged at the wall while the other end supports a 1-ton load. Determine tension T in the rope and the horizontal and vertical reactions at the hinge. 50° 60° Hint: Draw FBD of the forces involved and apply the two conditions of equilibrium.

2. A rope helps to support a uniform 800-N beam 7 m long the lower end of which is hinged at the wall while the other end supports a 1-ton load. Determine tension T in the rope and the horizontal and vertical reactions at the hinge. 50° 60° Hint: Draw FBD of the forces involved and apply the two conditions of equilibrium.

Glencoe Physics: Principles and Problems, Student Edition

1st Edition

ISBN:9780078807213

Author:Paul W. Zitzewitz

Publisher:Paul W. Zitzewitz

Chapter8: Rotational Motion

Section8.3: Equilibrium

Problem 40PP

See similar textbooks

Similar questions

A 15.0-in uniform ladder weighing 500 N rests against frictionless wall. The ladder makes a 60.0 angle ESI with the horizontal, (a) Find the horizontal and vertical forces the ground exerts on the base of the ladder when an 800-N firelighter has climbed 4.00 m along the ladder from the bottom, (b) If the ladder is just on the verge of slipping when the firefighter is 9.00 m from the bottom, what is the coefficient of static friction between ladder and ground?
In order to get his car out of the mud, a man ties one end of a rope to the front bumper and the other end to a tee 15 m away as shown below. He then pulls on the center of the rope with a force of 400 N, which causes its center to be displaced 0.30 m, as shown. What is the force of the rope on the car?
A uniform horizontal strut weighs 400.0 N. One end of the strut is attached to a hinged support the wall and the other end of the strut is attached to a sign that weighs 200.0 N The strut is also supported by a cable attached between the end of the strut and the wall. Assuming that the entire weight of the sign is attached at the very end of the s find the tension in the cable and the force at the hinge of the strut.
Suppose a 900-kg car is on the bridge in Figure 9.34 with its center of mass halfway between the hinges and the cable attachments. (The bridge is supported by the cables and hinges only.) (a) Find the force in the cables. (b) Find the direction and magnitude of the force exerted by the hinges on the bridge.
Suppose the weight of the drawbridge in Figure 9.34 is supported entirely by its hinges and the opposite shore, so that its cables are slack. (a) What fraction of the weight is supported by the opposite shore if the point of support is directly beneath the cable attachments? (b) What is the direction and magnitude of the force the hinges exert on the bridge under these circumstances? The mass of the bridge is 2500 kg.
Can Young’s modulus have a negative value? What about the bulk modulus?
Two thin rods, one made of steel and the other of aluminium, are joined end to end. Each rod is 2.0m long and has cross-sectional area 9.1mm2 . If a 10,000N tensile force is applied at each end of the combination, find: (a) stress in each rod; (b) strain in each rod; and, (c) elongation of each rod.
In Figure 9.21, the cg of the pole held by the pole vaulter is 2.00 m from the left hand, and the hands are 0.700 m apart. Calculate the force exerted by (a) his right hand and (b) his left hand. (c) If each hand supports half the weight of the pole in Figure 9.19, show that the second condition for equilibrium (net =0 ) is satisfied for a pivot other than the one located at the center of gravity of the pole. Explicitly show how you follow the steps in the Problem-Solving Strategy for static equilibrium described above. Figure 9.21 A pole vaulter is holding a pole horizontally with both hands. The center of gravity is to the left side of the vaulter.
Explain the need for tall towers on a suspension bridge to ensure stable equilibrium.
Alarge uniform cylindrical steel rod of density =7.8g/cm3 is 2.0 m long and has a diameter of 5.0 cm. the rod is fastened to a concrete floor with its long axis vertical.what is the normal stress in the rod at the cross-section located at (a)1.0 mfrom its lower end?(b)1.5 m from the lower end?
Assume Youngs modulus for bone is 1.50 1010 N/m2. The bone breaks if stress greater than 1.50 108 N/m2 is imposed on it. (a) What is the maximum force that can be exerted on the femur bone in the leg if it has a minimum effective diameter of 2.50 cm? (b) If this much force is applied compressively, by how much does the 25.0-cm-long bone shorten?
If an odd number of forces act on an object, the object cannot be in equilibrium.