2. A surface condenser serving a 60 MW steam-turbo generator unit receives exhaust steam at the rate of 200,000 kg/hr. Vacuum in condenser is 0.88025 bar. Sea water for cooling enters at 27°C and leaves at 40°C. For steam turbine condenser as heat given up to cooling water, calculate the LMTD.

2. A surface condenser serving a 60 MW steam-turbo generator unit receives exhaust steam at the rate of 200,000 kg/hr. Vacuum in condenser is 0.88025 bar. Sea water for cooling enters at 27°C and leaves at 40°C. For steam turbine condenser as heat given up to cooling water, calculate the LMTD.

Refrigeration and Air Conditioning Technology (MindTap Course List)

8th Edition

ISBN:9781305578296

Author:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson

Publisher:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson

Chapter45: Domestic Refrigerators And Freezers

Section: Chapter Questions

Problem 12RQ: Refrigerators currently being manufactured in the United States are using______as their refrigerant.

See similar textbooks

Related questions

Q: The pump in Fig. 7.20 delivers water from the lower to the upper reservoir at the rate of 2.0 ft/s.…

A: Given:Water velocity, V=2.0 ft/sEnergy loss in suction pipe, hL,s=6 lb.ft/lbEnergy loss in discharge…

Q: Pendulum A is swinging with v= 0.3 m/s and reducing at a rate of 0.5 m/s every second when 0 = 30°…

A: Given v = 0.3 m/s a = 0.5 m/s²

Q: A container lying horizontally is filled with water. It is 5 ft long and its cross section is in the…

A: Solution: Given Data: H=5 ftD=3 ftρg=62.4 lb/ft3 To Find: (a) The illustration of the given…

Q: A large-particle composite consisting of tungsten particles within a copper matrix is to be…

Q: Required information A four-cylinder, four-stroke, spark-ignition engine operates on the ideal Otto…

Q: Find the moment of inertia I y about the y' axis. y'

Q: Calculate the number of vacancies per cubic meter in gold (Au) at 900°C. The energy for vacancy…

Q: Fatigue test are carried out

A: Fatigue test or Rotating beam is carried to know the fatigue stress, in which the beam is rotating…

Q: 3. Find the moment of inertia for the x and y axes.

Q: A geothermal well produces 65 kg/s of saturated liquid water at 230°C. The water is used in a…

Q: A solid shaft made of aluminum alloy (E=70 Gpa, v=0.33). The diameter of the shaft is 25 mm, and…

A: Introduction The strain represents the change in dimension of the body under the loading compared to…

Q: Question 4. An "ice-cream cone"-shaped solid of constant density 6 = 1 occupies the region D given…

A: Draw the diagram of solid cone shaped ice-cream in co-ordinate axis.

Q: Consider a moist air mass at P-950mb pressure with water vapor mixing ratio w=4x10. Calculate the…

A: Given data:- Total Pressure of moist air (PT)=950 mb Water Vapor mixing ratio=4×10-3 To find:-Water…

Q: A Diesel cycle has a compression ratio of 22 and begins its compression at 87 kPa and 15°C. The…

A: Given data: Compression ratio = R = V1V2= 22 Pressure before compression = P1 = 87 kPa Temperature…

Q: A chamber wall (1m x 2m) has an inside temperature of -4°C. The outside temperature is 22°C. The…

A: Given:Area of the wall, A=1m*2m=2 m2Inside temperature, Ti=-4oCOutside temperature, To=22oCThickness…

Q: The automobile has a weight 3.158-lb and travels forward at 8ft/s when it crashes into the wall and…

Q: 15mg per kg body weight 25mg per 1cc 5.5lbs give: ____ cc

Q: A large blower for a furnace delivers 47 000 ft/min (CFM) of air having a specific weight of 0.075…

A: Given: V˙ =47000 ft3/min γ=0.075 lb/ft³ To find: W˙ and m˙

Q: Air at a pressure of 1bar and a temperature of 300K (Kelvin), which can be modeled as an ideal gas;…

Q: fixed support at the base. The support at the top prevents both lateral deflec- tion and rotation.…

Q: The net power output of the steam cycle is 40 MW. If the pressure bounds on the cycle are 5 MPa and…

A: Solution: Given Data: W.net=40 MWP1=5 MPaP2=300 kPaT1=450oCT2=100oC To Find: The mass flow rate of…

Q: Compute the moments of inertia with respect to the X-X and Y-Y centroidal axes for the following…

A: Given data as per the question length of square 80 mm The diameter of semi circle = 45 mm

Q: An oil heater heats 60 kg per minute of oil from 28°C to 70°C in a counter-flow heat exchanger. The…

Q: Air flows in a pipe under fully developed conditions with an average velocity of 1.25 m/s and a…

Q: EXPLAIN THIS SOLUTION USING ONLY WORDS SO I CAN UNDERSTAND IT BETTER

Q: 3) Olive oil is cooled from 90°C to 20°C in a heat exchanger using water. Water enters the heat…

Q: Problem 10.34 Take that a = 36 mm. (Figure 1) Figure Part A Iy = 5a Determine the moment of inertia…

Q: Compute the moments of inertia with respect to the X-X and Y-Y centroidal axes for the following…

A: Given: R=45/2=22.5 mm

Q: Refrigerant 134a is used as the working fluid in an OTEC power plant, which utilizes a simple…

Q: A reversibly operating heat engine operates between two reservoirs with temperatures between 600 ℃…

Q: t 30° 15° R = 20 m D B B₁

A: Given situation is, vA= 72 km/h or 20 m/s aA= -3 m/s2 vB= 108 km/h or 30 m/s aB= 1 m/s2

Q: A cube of material with edge lengths d and specific weight 2y is suspended by a cable and submerged…

A: for solution refer below images.

Q: C1.3 If a = 120°, B = 45°, y = 60°, and F = 400 direction angles of the resultant force acting on…

Q: 3-66 A 4-m-high, 5-m-wide rectangular plate blocks the end of a 4-m-deep freshwater channel, as…

Q: 1. Consider the structure shown, which was designed to support a load. It consists of a boom AB with…

A: Only one question is allowed to solve as per the

Q: 5. वि० D 10' F is the orange arrow C 10' B 45* 1000lbs Find FAD, FBC, FCD FAB FAC TH

Q: P7.3 For the cantilever beam and loading shown in Figure P7.3, (a) derive equations for the shear…

Q: Each line of the following table gives data, in Btu, for a process of a closed system. Determine the…

Q: Draw the shear-force and bending moment diagrams for the beam shown. Determine the maximum positive…

Q: Compute the moments of inertia with respect to the X-X and Y-Y centroidal axes for the following…

Q: Which of the following is NOT an impact of IP infringement? O O O O Loss of market share O damage to…

A: Due to IP infringement there will be loss of market share because same products manufactured by…

Q: The sketch shows a flat plate aligned parallel to an incompressible airstream. Assume a velocity…

A: Given Data: flat plate aligned parallel to an incompressible airstream Find: Assume a velocity…

Q: (M011) 1. Find the degrees of freedom of the following mechanisms. a. J Cam contact P Pin in slot

Q: An engine, running at 350 r.p.m., drives a line shaft by means of a belt. The engine pulley is 950…

Q: A shaft 70-mm in diameter is being pushed at a speed of 400mm/s through a bearing sleeve 70.2-mm in…

A: Given Data- D=70.2mm d=70mm L=250mm U=450 mm/s kinematic viscosity of v = 0.005 m2/s Specific…

Q: ! Required information A 50-cm x 50-cm circuit board that contains 121 square chips on one side is…

Q: A power-generating unit runs the simple Rankine cycle with a mass flow rate of 24,000 kg/h. Water…

Q: The engineering stress-strain curve below was obtained for a precipitation hardened Aluminum alloy.…

A: Given:

Q: 17. A 30 kg iron was put in a container with 14.33 kg water. The water is at 100C and the iron has…

A: Given: For Iron- Mass of iron = miron=30 kg Initial temperature of iron = Ti,iron=439 K Specific…

Q: D. If the critical load for the valve push for an overhead valve engine is 380 lbs, calculate the…

A: Given data as per the question Critical load =380 lbslength =1 ft=12 inEsteel=2.9 ×107 psi

Question

please answer asap

Show complete solutions and detailed drawings

also please show the steam table that is used in this problem

2. A surface condenser serving a 60 MW steam-turbo generator unit receives
exhaust steam at the rate of 200,000 kg/hr. Vacuum in condenser is 0.88025 bar.
Sea water for cooling enters at 27°C and leaves at 40°C. For steam turbine
condenser as heat given up to cooling water, calculate the LMTD.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Step by step

Solved in 3 steps with 3 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Why is two-stage compression popular for extra-low-temperature refrigeration systems?
Condensers in these refrigerators are all_______cooled.
A 1000-MW supercritical double-reheat steam power plant operates withthe main (live) steam condition of 250 bars and 560°C and the condenserpressure of 0.04 bar. The steam is reheated first at 30 bars to 560°C andthen at 4 bars to 560°C. The turbine efficiency is 0.92. The feed pumpwork may be ignored. Calculate: (a) the plant net specific work, (b) the plant thermal efficiency, (c) the plant steam mass flow rate, and (d) the plant heat rate.
A reheat cycle with two stages of reheating is executed, with steam expanding initially from 90 bar and 530°C. The two reheater pressures are 10 bar and 0.6 bar, and the steam leaves each reheater at 480°C. Condensation occurs at 0.03 bar. For the engine, ignore the pressure drop through the reheaters, let the engine operate through the same states, and compute W in kJ/kg.
Steam is supplied to a two-stage turbine at 40 bar and 350 oC. It expands in the first turbine until it is just dry saturated, then it is reheated to 350 oC and expanded through the second stage turbine; the isentropic efficiencies of the first and second stage turbines are 84 % and 78 % respectively. The condenser pressure is 0.035 bar. Sketch the process on a T-s diagram and calculate;The work output and heat supplied per kg of steam for the plant assuming ideal processesThe thermal efficiency of the cycleThe specific steam consumption
Steam is supplied to a two-stage turbine at 40 bar and 350 o It expands in the first turbine until it is just dry saturated, then it is reheated to 350 oC and expanded through the second stage turbine; the isentropic efficiencies of the first and second stage turbines are 84 % and 78 % respectively. The condenser pressure is 0.035 bar. Sketch the process on a T-s diagram and calculate; i. The work output and heat supplied per kg of steam for the plant assuming ideal processes ii. The thermal efficiency of the cycle iii. The specific steam consumption
Air enters the compressor of an ideal gas refrigeration cycle at 12°C and 50 kPa and the turbine at 47°C and 250 kPa. The mass flow rate of air through the cycle is 0.08 kg/s. Assuming variable specific heats for air, determine (a) the rate of refrigeration, (b) the net power input, and (c) the coefficient of performance.
Refrigerant 134a enters a refrigerator compressor as superheated vapor at 0.20 MPa and -5 ° C at a rate of 0.7 kg / s, and exits at 1.2 MPa and 70 ° C. The refrigerant is cooled in the condenser to 44 ° C and 1.15 MPa, and is throttled to 0.2 MPa. Neglecting any heat transfer and any pressure drop in the connecting lines between the components, show the cycle on a Ts and Ph diagram with respect to the saturation lines, and determine (a) the rate of heat removal from the refrigerated space and the power input to the compressor, b) the isentropic efficiency of the compressor, and c) the COP of the refrigerator
1. Steam is supplied to a two-stage turbine at 140 bar and 400C. It expands isentropic ally until it is just dry-saturated. Then it is reheated to 350C at constant pressure and expanded in the second-stage turbine to the condenser pressure of 0.2 bar. If the isentropic efficiency of the second stage is 78%. Calculate the specific steam consumption and the thermal efficiency. Determine the pressure in reheater also to solve the whole problem
Refrigerator 1 simulates an ideal refrigerator and therefore operates on a Carnot cycle using R-134a as the refrigerant at a flow rate of 1.4 kg/sec. The condensing and evaporating temperatures are 30 °C and -10 °C, respectively. To assess the performance of Refrigerator 1, you must submit the report. of the project with the following information: d) The work generated by the turbine; e) The condenser heat rejection rate (Q H); f) The coefficient of performance of the cycle.
Refrigerant R12 is used in a vapour compression cycle. The saturated vapour entersthe compressor at -18.8°C, and subsequently leaves at 75°C and 10 bar. Thesaturated liquid leaving the condenser is at 10 bar. The resulting stream is throttledand evaporated before being fed back to the compressor. a) Determine the coefficient of performance of the refrigerator. Take the specific enthalpy,h, at 10 bar and 36 K of superheat to be 163.7 kJ/kgb) Obtain the isentropic efficiency of the compressor. Take the specific entropy, s, at 10bar to be 1.188 kJ/kg
A steam power plant operates between the pressure limit of 3.0 Mpa for the boiler and 40 kPa for the condenser. If the plant operates in an ideal Rankine cycle with superheated vapor enters the turbine at 3 Mpa and 500 oC, determine:a) the moisture content at the inlet of the condenser,b) the net work per unit mass of steam flowing, in kJ/kg,c) the heat transfer to the steam in the boiler in kJ per kg of steam,d) the thermal efficiency,e) the heat transfer to cooling water passing through the condenser, in kJ per kg of steam flowing. h1 (kJ/kg) Format : 227.25 v1 (m3/kg) Format : 0.002092 h2 (kJ/kg) Format : 320.445 h3 (kJ/kg) Format : 8765.2 s3 (m3/kg) Format : 4.7267 x4 Format : 0.959 h4 (kJ/kg) Format : 7845.82 W (kJ/kg) Format : 555.79 Qin (kJ/kg) Format : 6362.75 Efficiency (%) Format : 50.83