Air flows in a pipe under fully developed conditions with an average velocity of 1.25 m/s and a temperature of 24°C. The pipe's inner diameter is 4 cm, and its length is 4 m. The first half of the pipe is kept at a constant wall temperature of 100°C. The second half of the pipe is subjected to a constant heat flux of 200 W. The properties of air at 80°C are p = 0.9994 kg/m³, k = 0.02953 W/m-K, v= 2.097 x 10-5 m²/s, cp= 1008 J/kg-K, and Pr = 0.7154. NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to this part. Air 1.25 m/s 2m T₁ = 100°C D = 4 cm 2 m Q₁ = 200 W Determine the air temperature at the 2 m length. The air temperature at the 2 m length is 47.91 * °C.

Air flows in a pipe under fully developed conditions with an average velocity of 1.25 m/s and a temperature of 24°C. The pipe's inner diameter is 4 cm, and its length is 4 m. The first half of the pipe is kept at a constant wall temperature of 100°C. The second half of the pipe is subjected to a constant heat flux of 200 W. The properties of air at 80°C are p = 0.9994 kg/m³, k = 0.02953 W/m-K, v= 2.097 x 10-5 m²/s, cp= 1008 J/kg-K, and Pr = 0.7154. NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to this part. Air 1.25 m/s 2m T₁ = 100°C D = 4 cm 2 m Q₁ = 200 W Determine the air temperature at the 2 m length. The air temperature at the 2 m length is 47.91 * °C.

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter7: Forced Convection Inside Tubes And Ducts

Section: Chapter Questions

Problem 7.31P

See similar textbooks

Similar questions

5.7 The average Reynolds number for air passing in turbulent flow over a 2-m-long, flat plate is . Under these conditions, the average Nusselt number was found to be equal to 4150. Determine the average heat transfer coefficient for an oil having thermal properties similar to those in Appendix 2, Table 18, at at the same Reynolds number and flowing over the same plate.
An electrical transmission line of 1.2-cm diameter carries a current of 200 amps and has a resistance of 310-4 ohm per meter of length. If the air around this line is at v, determine the surface temperature on a windy day, assuming a wind blows across the line at 33 km/h.
Air is flowing in parallel over the upper surface of aflat plate with a length of 4 m. The first half of the plate length,from the leading edge, has a constant surface temperatureof 50°C. The second half of the plate length is subjected toa uniform heat flux of 86 W/m2. The air has a free streamvelocity and temperature of 2 m/s and 10°C, respectively.Determine the local convection heat transfer coefficients at1 m and 3 m from the leading edge. Evaluate the air propertiesat a film temperature of 30°C. Is the film temperatureTf = 30°C applicable at x = 3 m?
Air is flowing in parallel over the upper surface of a flat plate with a length of 4m. The first half of the plate length, from the leading edge, has a constant surface temperature of 50 degrees Celsius. The second half of the plate length is subjected to a uniform heat flux of 86 W/m2. The air has a free stream velocity and temperature of 2 m/s and 10 degrees Celsius, respectively. Determine the local convection heat transfer coefficients at 1 m and 3 m from the leading edge. Evaluate the air properties at a film temperature of 30 degrees Celsius. Is the film temperature Tf=30 degrees Celsius applicable at x = 3 m?
Air is flowing in parallel over the upper surface of a flat plate with a length of 4 m. The first half of the plate length, from the leading edge, has a constant surface temperature of 50°C. The second half of the plate length is subjected to a uniform heat flux of 86 W/m2. The air has a free stream velocity and temperature of 0.5 m/s and 10°C respectively. The properties of air at Tf = 30°C are k = 0.02588 W/m∙K, ν = 1.608 × 10−5 m2/s, and Pr = 0.7282. Determine the local convection heat transfer coefficients at 1 m and 3 m from the leading edge.
Air is flowing in parallel over the upper surface of a flat plate with a length of 4 m. The first half of the plate length, from the leading edge, has a constant surface temperature of 50°C. The second half of the plate length is subjected to a uniform heat flux of 86 W/m2. The air has a free stream velocity and temperature of 0.5 m/s and 10°C respectively. The properties of air at Tf = 30°C are k = 0.02588 W/m∙K, ν = 1.608 × 10−5 m2/s, and Pr = 0.7282.Determine the local convection heat transfer coefficients at 1 m from the leading edge.
During a cold winter day, wind at 55 km/h is blowing parallel to a 4m high and 10m long wall of a house. If the air outside is at 5 degrees Celsius and the surface temperature of the wall is 12 degrees Celsius , determine the rate of heat loss from the wall by convection. What would your answer be if the wind velocity has doubled? From Table A-1:thermal conductivity, k = 0.0246 W/m degrees Celsiusviscosity, v = 1.4 x 10^-5 m^2/sPrandtl no. Pr = 0.717
Liquid mercury at 250°C is flowing with a velocity of 0.3 m/s in parallel over a 0.1-m-long flat plate where there is an unheated starting length of 5 cm. The heated section of the flat plate is maintained at a constant temperature of 50°C. Determine (a) the local convection heat transfer coefficient at the trailing edge, (b) the average convection heat transfer coefficient for the heated section, and (c) the rate of heat transfer per unit width for the heated section.
. Castor oil at 36 °C flows over a 6 m long and 1 m wide heated plate at 0.06 m/s. For a surfacetemperature of 96 °C, determine (i) the thermal boundary layer thickness at the end of the plate,(ii) the local heat transfer coefficient at the end of the plate, and (iii) the rate of heat transfer fromthe entire plate
A 6cm diameter shaft rotates at 3000rpm in a 20cm long bearing with a uniform clearance of 0.2mm. At steady operating conditions, both the bearing and shaft in the vicinity of the oil gap are 50°C. The thermal conductivity and the viscosity of the lubricating oil are k=0.17 W/m-K and µ= 0.05 N-s/m2, respectively. By simplifying and solving the differential continuity, momentum and energy equation, determine the maximum temperature of oil. (Hint: Couette flow)
Prove that the thermocouple will underestimate the temperature of airflow by more than 15% but less than 30% in a large air duct if the temperature of the hot air is 1367 K, duct-wall temperature is 533 K, emissivity of the thermocouple is 0.5, and the convection heat-transfer coefficient is 114 W/m2 -K.
Consider laminar flow of air across a hot circular cylinder. At what point on the cylinder will the heat transfer be highest? What would your answer be if the flow were turbulent?