2. Consider airflow over a plate surface maintained at a temperature of 215°C. The temperature profile of the airflow is given as T(y) = Too - (To T.) exp V fluid The airflow at 1 atm has a free stream velocity and temperature of 5 cm/s and 25°C, respectively. Determine the heat flux on the plate surface and the convection heat transfer coefficient of the airflow.

2. Consider airflow over a plate surface maintained at a temperature of 215°C. The temperature profile of the airflow is given as T(y) = Too - (To T.) exp V fluid The airflow at 1 atm has a free stream velocity and temperature of 5 cm/s and 25°C, respectively. Determine the heat flux on the plate surface and the convection heat transfer coefficient of the airflow.

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter7: Forced Convection Inside Tubes And Ducts

Section: Chapter Questions

Problem 7.20P

See similar textbooks

Similar questions

5.7 The average Reynolds number for air passing in turbulent flow over a 2-m-long, flat plate is . Under these conditions, the average Nusselt number was found to be equal to 4150. Determine the average heat transfer coefficient for an oil having thermal properties similar to those in Appendix 2, Table 18, at at the same Reynolds number and flowing over the same plate.
The airflow at 1 atm has a free stream velocity and temperature of 5 cm/s and 25°C, respectively. Determine the heat flux on the plate surface and the convection heat transfer coefficient of the airflow.
Please help with this questionHot carbon dioxide exhaust gas at 1 atm is being cooled by flat plates. Thegas at 220°C flow is parallel over the upper and lower surfaces of a 3-m-longflat plate at a velocity of 3 m/s. If the flat plate surface temperature ismaintained at 80°C.Determine the local convection heat transfer coefficient at 1 m fromthe leading edge and calculate the average convection heat transfer coefficient over theentire plate.
Consider laminar flow of air across a hot circular cylinder. At what point on the cylinder will the heat transfer be highest? What would your answer be if the flow were turbulent?
Liquid mercury at 250°C is flowing with a velocity of 0.3 m/s in parallel over a 0.1-m-long flat plate where there is an unheated starting length of 5 cm. The heated section of the flat plate is maintained at a constant temperature of 50°C. Determine (a) the local convection heat transfer coefficient at the trailing edge, (b) the average convection heat transfer coefficient for the heated section, and (c) the rate of heat transfer per unit width for the heated section.
Air is flowing in parallel over the upper surface of aflat plate with a length of 4 m. The first half of the plate length,from the leading edge, has a constant surface temperatureof 50°C. The second half of the plate length is subjected toa uniform heat flux of 86 W/m2. The air has a free streamvelocity and temperature of 2 m/s and 10°C, respectively.Determine the local convection heat transfer coefficients at1 m and 3 m from the leading edge. Evaluate the air propertiesat a film temperature of 30°C. Is the film temperatureTf = 30°C applicable at x = 3 m?
Hot carbon dioxide exhaust gas at 1 atm is being cooled by flat plates. The gas at 220oC flows in parallel over the upper and lower surfaces of a 1.5-m-long flat plate at a velocity of 3m/s. if the flat plate surface temperature is maintained at 80oC, determine (a) the local convection heat transfer coefficient at 1 m from the leading edge, (b) the average convection heat transfer coefficient over the entire plate, and (c) the total heat flux transfer to the plate.
The local atmospheric pressure in Denver, Colorado (elevation 1610 m), is 83.4 kPa. Air at this pressure and at 30°C flows with a velocity of 4.8 m/s over a 2.3-m × 8-m flat plate whose temperature is 120°C. Determine the rate of heat transfer from the plate if the air flows parallel to the 2.3-m-side. The properties of air at 0.823 atm and at the film temperature of (120 + 30)/2 = 75°C are k = 0.02971 W/m·°C, ν = 2.486 × 10-5 m2/s, and Pr = 0.7166.
What is the physical significant of prandtl number? Question does the value of the prandtl number depend on the type of flow, or the flow geometry? Does the prandtl number of air change with pressure? does it change your temperature?
. Castor oil at 36 °C flows over a 6 m long and 1 m wide heated plate at 0.06 m/s. For a surfacetemperature of 96 °C, determine (i) the thermal boundary layer thickness at the end of the plate,(ii) the local heat transfer coefficient at the end of the plate, and (iii) the rate of heat transfer fromthe entire plate
Write the definition ,formula and significance of Reynolds number and Grashoff number in convection heat transfer.
Consider a 25-mm-diameter and 15-m-long smooth tube that is maintained at a constant surface temperature. Fluids enter the tube at 50°C with a mass flow rate of 0.01 kg/s. Determine the tube surface temperatures necessary to heat water, engine oil, and liquid mercury to the desired outlet temperature of 150°C.