2. Consider the circuit shown below. Assume the capacitor is initially uncharged, and the switch is closed at t = 0s. + SW1 BAT1 12 V ww R1 1.25 ΚΩ C1 120 μF (a) What is the maximum current that will go through this circuit? When will this occur? (b) At what time will the voltage across the capacitor be 10V? (c) What will the current and charge on each plate of the capacitor be at this time?

2. Consider the circuit shown below. Assume the capacitor is initially uncharged, and the switch is closed at t = 0s. + SW1 BAT1 12 V ww R1 1.25 ΚΩ C1 120 μF (a) What is the maximum current that will go through this circuit? When will this occur? (b) At what time will the voltage across the capacitor be 10V? (c) What will the current and charge on each plate of the capacitor be at this time?

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

A 500 ohm resistor, an 1.5 F uncharged capacitor, and a 6.16-V emf are connected in series. (a) What is the initial current? (b) What is the time constant? (c) What is the final voltage on the capacitor? (d) what is the final charge on the capacitor? What is the final energy stored in the capacitor? (e) Express (i) Current in the circuit, (ii) Voltage on the capacitor, (iii) Charge accumulated on either plate of capacitor, (iv) energy stored in the capacitor as a function of time. (must include all the value calculated in the earlier part). (f) What is the i) current ii) charge on capacitor, iii) voltage on capacitor & iv) Energy stored in the capacitor after one time constant?
The triangular voltage pulse shown below is applied to a 200 mF capacitor. a) Write the expressions thatdescribe vc(t) in the five time intervals t < 0, 0 ≤ t ≤ 2 , 2 ≤ t ≤ 6, 6 ≤ t ≤ 8, and t > 8. b) Derive theexpressions for the capacitor current, power, and energy for the time intervals in part (a).
IN THE CIRCUIT SHOWN, CONSIDER THAT V1=20 VDC, R1=1000 Ω, R2=3000 Ω, R3=3500 Ω AND C=1 mF.DETERMINE:A) THE TIME IT TAKES FOR THE CAPACITOR TO REACH ITS FINAL VALUE (5T), WHEN SWITCH 2 (INT 2) IS IN POSITION A AND SWITCH 1 (INT 1) IS CLOSED AT t=0,B) THE ENERGY STORED BY THE CAPACITOR ONCE IT HAS BEEN FULLY CHARGED WITH THE SAME POSITION OF SWITCHES AS ITEM A)C) ONCE THE CAPACITOR HAS BEEN FULLY CHARGED WITH SWITCH 1 CLOSED, SWITCH 2 MOVES POSITION (GOES TO B) AT A NEW t=0. NOW DETERMINE THE VALUE OF THE VOLTAGE ON THE CAPACITOR AT t=3.5 SECONDS
Given the capacitance of four capacitors Ca= 30 µF, Cb = 10 µF, Cc = 40 µF and Cd = 12 µF. If Cb and Cc are connected in series and the series combination is connected in parallel with Cd then the whole combination is connected in series with Ca, Calculate (a) the equivalent capacitance (b) the voltage across each capacitor if the circuit is supplied by 250 volts DC source (c) the charge on each capacitor.
capacitor having capacitance of 10uF is connected with 1k ohm resistor in series. The switch of the DC supply of 10 Volts, closes at t = 0. Compute the following a. Draw a circuit diagram for t- and t+ b. Compute the time constant c. Plot the Voltage with respect to time, showing the behavior of capacitor charging(take at least 10 values of time in seconds to draw a graph).
Derive an expression for the electrical energy stored in a capacitor of capacitance C when charged to a potential difference V. If C = 2µF and V= 4V, calculate(l.) the final energy stored in the capacitor,(II.) the work done by the battery in the charging process Account for any difference between your answers in parts (I) and (II) above
Given the capacitance of four capacitors Ca= 30 µF, Cb = 20 µF, Cc = 40 µF and Cd = 10 µF. If Cb and Cc are connected in parallel and the parallel combination is connected in series with Ca and the combination is further connected in parallel with Cd, calculate (a) the equivalent capacitance (b) the voltage across each capacitor if the circuit is supplied by 240 volts DC source (c) the charge on each capacitor.
Can you please help with this question? The triangular voltage pulse shown below is applied to a 200 mF capacitor. a) Write the expressions thatdescribe vc(t) in the five time intervals t < 0, 0 ≤ t ≤ 2 , 2 ≤ t ≤ 6, 6 ≤ t ≤ 8, and t > 8. b) Derive theexpressions for the capacitor current, power, and energy for the time intervals in part (a).
An electrical circuit contains a resistance R ohms and a capacitor C farads which initially holds acharge Q coulombs. The rate of discharge of the capacitor is given by the equation dQ/dt + Q/RC =0where t is the time in seconds. If R = 80,000 ohms and C = 0·3x 10^-6 farads and also Q = 0·0015coulombs initially, find the equation connecting Q and t. Find Q when t = 0·02 seconds and also twhen Q = 0·001 coulombs
. A 47,000 µF capacitor, initially charged to 100 V, is discharged by a steady current of 1 mA. How long does it take to discharge the capacitor to 0 V? a. Is this discharge time long or slow? Explain
Q1 (True/False): A) The current through the capacitor is inversely proportional to the derivative of the voltage across it: Is it true or false? B) In a typical electronic circuit the capacitor blocks DC and couplest he AC to the next stage of the circuit: Is it true or false? C) The more the value of the stray capacitance , the better it is: Is it true or false?
a.)If the current through a 1-mH inductor is i(t) = 20 cos 100t mA, find the terminal voltage and the energy stored. b.)The terminal voltage of a 2-H inductor is v = 10(1 – t ) V. Find the current flowing through it at t = 4 s and the energy stored in it at t = 4 s. Assume i(0)=2A.