2. Design a full wave rectifier for a regulator that delivers 100W electrical power to a white off-the-shelf LED. Per datasheet, the LED requires 33V and draws 3A current. You are required to limit the ripple voltage to less than 20% of average DC voltage of the output. Assume all diodes have Von=0.7V and negligible off current. a. Draw the circuit diagram. b. Determine the voltage of transformer and capacitance of the filter

2. Design a full wave rectifier for a regulator that delivers 100W electrical power to a white off-the-shelf LED. Per datasheet, the LED requires 33V and draws 3A current. You are required to limit the ripple voltage to less than 20% of average DC voltage of the output. Assume all diodes have Von=0.7V and negligible off current. a. Draw the circuit diagram. b. Determine the voltage of transformer and capacitance of the filter

Electric Motor Control

10th Edition

ISBN:9781133702818

Author:Herman

Publisher:Herman

Chapter59: Motor Startup And Troubleshooting Basics

Section: Chapter Questions

Problem 12SQ: How is a solid-state diode tested? Explain.

See similar textbooks

Similar questions

What is the difference between a diode and rectifier?
How is a solid-state diode tested? Explain.
What is CEMF?
In a center-tapped full wave rectifier circuit utilizing ideal diodes, if the primary voltage is 160Vpeak, the turns ratio is 8:1 and the load resistance is 860 ohms, what is the rectified dc voltage at the output? express answer in volts
The full-wave rectiﬁer ias shown is operating at a frequency of 60 Hz, and the rms value of the transformer output voltage is 18 V. (a) What is the value of the dc output voltage if the diode voltage drop is 1 V? (b) What is the minimum value of C required to maintain the ripple voltage to less than 0.25 V if R = 0.5 Ω? (c) What is the PIV rating of the diode in this circuit? (d) What is the surge current when power is ﬁrst applied? (e) What is the amplitude of the repetitive current in the diode?
3.4 PRE-LABORATORY QUESTIONS 1. What is a rectifier? 2. How does a diode act as a rectifier? 3. What is the significance of PIV? What is the condition imposed on PIV? 4. What is meant by regulation? 5. What is meant by time constant? 6. What is meant by ripple factor?
Determine the peak output voltage for the bridge rectifier in this figure. Assuming the practical model, what PIV rating is required for the diode? The transformer is specified to have a 12 Vrms secondary voltage for the standard 110 V across the primary.
What is the PIV rating of each silicon diode in volts for a bridge type rectifier where the voltage in the secondary transformer is 100V peak? Assume 2.2K ohms load.
A three-phase, half-wave uncontrolled rectifier is fed from an ideal three-phase voltage source of 380V, 50 Hz. The load is resistive with R=15 2. Calculate: (a) The average output voltage and average load current of the rectifier. (b) The d.c. and a.c. power dissipations in the load. (c) The diode ratings. (d) What is the lowest ripple frequency of the output voltage waveform?
1N4001, 1N4002, 1N4003, 1N4004, 1N4005, 1N4006 and 1N4007 For any of the diodes, describe with the aid of diagrams/illustrations its applications in an AC to DC Bridge rectifier power supply circuit. For your circuit show and describe how you are going to smooth out the ripple voltage that will be present.
Assume the input signal to a rectifier circuit has a peak value of VM = 12 V and is at a frequency of 60 Hz. Assume the output load resistance is R = 2 k and the ripple voltage is to be limited to Vr = 0.4 V. Determine the capacitance required to yield this specification for a (a) full-wave rectifier and (b) half-wave rectifier.
The secondary input voltage to a single phase diode bridge rectifier is 50V, 50Hz, and the load can be replaced by a resistance of value 20ohms (a) Sketch a well labelled circuit of the converter described above. (b) Sketch the waveforms for the input voltage, output voltage, output current, and output current (c) Derive an equation for average output voltage and calculate for output dc voltage (d) Calculate the ripple factor of the output voltage (e) Transformer utilization factor (h) How can the ripple be improved