2. Draw the Free Body Diagram (FBD), Shear (V) Diagram and Moment Diagram (M). You should end up with the three Diagrams stacked. Make sure you calculate the maximum and minimum values for both Shear (V) and Moment (M), and label those points on your diagrams. Show distances on the X-axis at which Shear (V) and Moment (M) switch from positive to negative o negative to positive. 20 KN

2. Draw the Free Body Diagram (FBD), Shear (V) Diagram and Moment Diagram (M). You should end up with the three Diagrams stacked. Make sure you calculate the maximum and minimum values for both Shear (V) and Moment (M), and label those points on your diagrams. Show distances on the X-axis at which Shear (V) and Moment (M) switch from positive to negative o negative to positive. 20 KN

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter6: Beams And Cables

Section: Chapter Questions

Problem 6.42P: For the beam AB shown in Cases 1 and 2, derive and plot expressions for the shear force and bending...

See similar textbooks

Similar questions

Determine the Vmax and Mmax. Draw the shear and moment diagram of the loaded beam shown in the figure.
show the calculations for the Shear Body Diagram and Bending Moment Diagram.
From the given figures below, draw the shear and moment diagram of the beam.
Draw shear and moment diagram. Assuming x=0 from A side to x= 3 at B . ( explain in details)
Develop the Shear force and Bending moment calculations and draw the Shear force and Bending moment diagrams
When loads and moments are applied to the cantilever beam as shown in the picture below, draw the shear and bending moment lines.
A gantry crane of weight W=100 Kg moves across a bridge with the length I=5 m. The front axle of the crane (which is nearer end A) carries 3/4W whereas the rear axle (nearer end B) carries 1/4 W. The distance of the axles is b = 1/20. Determine the maximum value of the bending moment and enter your answer in N-m units.. Remember to also show all your work (FBDs, calculation steps, etc on the handworked file) HINT: Determine the shear and bending moment equations along the beam. Assume only concentrated loads at the front and rear axles.
Draw the shear-force and bending-moment diagram for the beam shown. Assume the upward reaction provided by the ground to be uniformly distributed. Let a = 5.0 ft, b = 3.4 ft, P = 25 kips, and w = 1.1 kips/ft. Label all significant points on each diagram. Determine the maximum value of (a) the internal shear force and (b) the internal bending moment.Note that answers may be positive or negative. Here, "maximum" refers to the largest magnitude value, but you should enter your shear force and bending moment with the correct sign, using the sign convention presented in Section 7.2 of the textbook. If the magnitudes of the largest positive and largest negative values are the same, enter a positive number.
A simply supported beam, 50mm wide by 100mm high and 300 mm long is subjected to a concentrated load of 3000 N at a point 100 mm from one of the supports. Draw the shear force and bending moment diagrams for the beam.
Draw the Shear Force Diagram (SFD) and Bending Moment Diagram (BMD) for a loaded simply supported beam shown below. 1KN 4KN
I need help drawing the shear and moment diagrams. And also calculating the values of the shear force and bending moment at midbeam. the correct answer is given in the diagram but I don't know how to solve for it.
Draw the Shear and Moment Diagram of the figure shown