8-22. The cylinder is confined by the brake, where 4, 0.4. Determine the required compression in the spring in order to resist a torque of 800 N m on the cylinder. The spring has a stiffness of k = 3 MN/m and an unstretched length of 60 mm. End C of member ABC %3D slides freely along the smooth vertical guide. Problem 8-22 B 250 mm 400 mm 200 mm

8-22. The cylinder is confined by the brake, where 4, 0.4. Determine the required compression in the spring in order to resist a torque of 800 N m on the cylinder. The spring has a stiffness of k = 3 MN/m and an unstretched length of 60 mm. End C of member ABC %3D slides freely along the smooth vertical guide. Problem 8-22 B 250 mm 400 mm 200 mm

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter1: Tension, Compression, And Shear

Section: Chapter Questions

Problem 1.9.18P: The piston in an engine is attached to a connecting rod AB, which in turn is connected to a crank...

See similar textbooks

Similar questions

A damper square mat is supporting a dead load weight of8 kN. Helical springs will be used to support the loadlocated at all corners with shearing stress of 120.6 Mpaat 20 turns. The spring has a deformation of 98.7 mmwith a mean radius of 80 mm. Design the minimumdiameter of the wire to support a load. Use G = 83 Gpa.
The torsional assembly consists of solid 1.6 in. diameter aluminum [G = 4,000 ksi] segments (1) and (3) and a central solid 2.0 in. diameter bronze [G = 6,500 ksi] segment (2). Segment lengths are L1 = L3 = 32 in. and L2 = 66 in. Concentrated torques of TB = 2T0 and TC = T0 are applied to the assembly at B and C, respectively. If the rotation angle at joint B must not exceed 3.0°, determine:(a) the maximum magnitude of T0 that may be applied to the assembly.(b) the maximum shear stress magnitude in aluminum segments (1) and (3).(c) the maximum shear stress magnitude in bronze segment (2).
Determine to the nearest millimeter the minimum diameter of the solid shaft if it is subjected to the gear loading. The bearings at A and B exert force components only in the y and z directions on the shaft. Base the design on the maximum distortion energy theory of failure with sallow = 150 MPa.
A load P is supported by two springs arranged in series. The upper spring has 20 turns of 19 mm diameter wire on a mean diameter of 150 mm. The lower spring consists of 15 turns of 12 mm diameter wire on a mead diameter of 125 mm. Determine the spring index of the lower spring in MPa if the total deformation is 76 mm and G of 83 GPa.
The aluminum alloy [G = 4000 ksi] pipe is fixed to the wall support at C. The bolt holes in the flange at A were supposed to align with mating holes in the wall support; however, an angular misaligment of 4° was found to exist. To connect the pipe to its supports, a temporary installation torque T'B must be applied to B to align flange A with the mating holes in the wall support. The outside diameter of the pipe is 5.5625 in. and its wall thickness is 0.258 in. The segment lengths are L1= 16 ft and L2 = 24 ft. a) Determine the temportary installation torque T'B that must be applied to B to align the bolt holes at A b) Determine the maximum shear stress τinitial in the pipe after the bolts are connected and the temporary installation torque at B removed c)Determine the magnitude of the maximum shear stress in segment (1) and (2) if an external torque TB= 150 kip-in. is applied at B after the bolts are connected
When drilling a well at a constant angular velocity, the bottom end of the drill pipe encounters a torsional resistance TA. Also, soil along the sides of the pipe creates a distributed frictional torque along its length, varying uniformly from zero at the surface B to tA at A. Determine the minimum torque TB that must be supplied by the drive unit to overcome the resisting torques, and calculate the maximum shear stress in the pipe. The pipe has an outer radius ro and an inner radius ri.
6-26. The loading on a control torque tube for an aileron of an airplane may be idealized by a uniformly varying torque Tx = kx in-lb/in, where k is a constant(see the figure). Determine the angle of twist of the free end. Assume IpG to be constant.
the solid steel sheft DF has a diameter of 25 mm and is supported by smooth bearings at D and E. It is coupled to a motor at F. which delivers 12kw of bower to the shift while turning at 50 rev/s if gears A ,B and C remove 3kw,4kw,5kw respectively . determine the maximum shear stress developed in the shift within Regions CF and BC. the shaft is free to turn in its support bearings D and F
The figure shows an internal rim-type brake having an inside rim diameter of 11in and a dimension R of 3.5 in. The shoes have a face width of 1.25 in. Find the braking torque and the maximum pressure for each shoe if the actuating force is 205 Ibf, the drum rotation is counterclockwise, and f=0.32. The maximum pressure on the right-hand shoe parp is [ 16.99] @ psi. The maximum pressure on the left-hand shoe pa| H is [100.813 | @ psi. The torque on the right-hand shoe Tgis [ .056 | @ kipin. The torque on the left-hand shoe T is [ .332| @ kipin. Total braking torque Tiotal s [-3887] @ Kip-in.
The journal bearings at A and B exert only x and z components of force on the shaft. Determine the shaft’s diameter to the nearest millimeter so that it can resist the loadings. Use the maximum distortion energy theory of failure with sallow = 200 MPa.
The corediameter of the double start square threaded screw having a pitch of 12mm is 50 mm. A load of 18kN is lifted through a distance of 180mm. Find the work done(in Joule)in lifting the loadand the efficiency of the screw, when 1. The load rotates with the screw, and 2. The load rests on the loose head which does not rotate with the screw. The external and internal diameter of the bearing surface of the loose head are 60 mm and 10 mmrespectively. The coefficient of friction for the screw is 0.11,whilefor the bearing surface is 0.13.
A square thread jackscrew has a 2 threads per inch. It is to lift 15tons. The friction radius of the collar is 1 in. The coefficient offriction between the threads of the screw and base is 0.15, thatbetween the screw and the collar is 0.13. Determine:a. The diameter of the root of the screw if theallowable stress in compression is 6 000 psi.b. The torque required to turn the screw.c. The pull required at the end of a 5 ft bar raises theload.d. The twisting moment exerted at the root of thethreads.e. The power output of the screw if it is turning at 60rpm.f. The power input of the screw.g. The efficiency of the screw and collar