2. Draw the influence lines for the support reactions and bending moment and for the shear and bending moment at section 1-1 of the beam shown in figure.

Q: A rough pipe of 0.5 m diameter, 300 m length and roughness height of 0.25 mm, carries water…

A: First we summarise the given data : Diameter of pipe = 0.5 m Length = 300 m Height = 0.25 mm…

Q: 500 N a P O a = 15.150 O a = 48.150 O a = 37.150 O a = 29.150 O a = 53.150 10 cm N=0 (@pt of…

A:

Q: 10 kN/m -5 m OB 15 KN -5 m- El = constant

A:

Q: A hollow cast-iron cylinder 4m long, with 300mm outer diameter, and thickness of metal 50 mm is…

A: Given : Length of cast iron cylinder = 4 m Outer diameter = 300 mm Thickness of metal = 50 mm Stress…

Q: SN/m пив TH с 2m 5 N/m -1.5- m 5 N.m

A: Given,  Moment = 5 N-m UDL = 5 N/m Uvl = 5 N/m Length of beam = 5.5 m

Q: : Find maximum factored uniformly distributed load "Wu" that can be supported?, where fe'=30 Mpa and…

A:

Q: Water is flowing under a sluice gate in a 30-ft wide rectangular channel. You observed a hydraulic…

A:

Q: 3. A square foundation is constructed in a soil deposit as shown in the figure below. Assume that…

A: Formula to calculate the ultimate bearing capacity of footing is given by qu = C'Nc Fcs Fcd Fci + q…

Q: What do the SPT and CPT stand for in subsurface exploration? Briefly describe theprocedure of SPT.

A: SPT and CPT are more frequent field test to determine the soil parameter.

Q: Use the manning's equation above to find the streamflow rate (Q) under the following conditions:

A: This question is from Open Channel Flow.

Q: H.W.13: For a simply supported beam with span 6.0 m, determine the area of steel required to…

A: Answer  We are given Beam span L = 6 m Width b  = 350 mm Total height h = 550 mm Service dead load…

Q: Use the design values for the coefficient C, from Table 8.3 unless stated otherwise. Use either of…

A: The given data is shown below: Flowrate=1.5 ft3/sLength of pipe=550 ftDiameter of pipe=6 in.

Q: A compound shaft consists of brass segment (1) and aluminum segment (2). Segment (1) is a solid…

A:

Q: A central beam BD is joined at hinges to two cantilever beams AB and DE. All beams have the cross…

A: Given : Allowable deflection at C = 2.1 mm E = 200 GPa This is a problem of Strength of materials…

Q: 1. Give the health and environmental effects of carbon monoxide, nitrogen dioxide, sulfur dioxide,…

A: Air pollution is contamination of the air (Indoor / Outdoor) due to the presence of any chemical,…

Q: For a certain loading condition, a saturated clay layer undergoes 40% consolidation in a period of…

A: Given- U = 40% consolidation, time t =160 days, Additional time required for further 10%…

Q: 1,0 m w G 4 m (ININININININI I DRY BARK CLAY | VINININININININININIK TIKININK y=18 kN/m³ PVP Y... Sa…

A:

Q: Q2 Use the Müller-Breslau principle to sketch the influence lines for the vertical reaction at A,…

A:

Q: 8. The national ambient air quality standard for sulfur dioxide is 80 ug m-³. Assuming an amount of…

A: Given  National ambient air quality standard for sulfur dioxide = 80 ×10-3 mg/m3  Amount of air…

Q: Using linear interpolation determine the DBTT of a given steel with the following Charpy tests…

A: The given data is shown below:

Q: What is the Demand-to-Capacity ratio of the W100x19.3 A36 Beam? Assume the is fully laterally…

A: Answer  Let us first calculate Moment demand 'Mu' for the given load on beam For simply supported…

Q: RAH A 60⁰ RAV 500 N E 60° 3m 60⁰ RAV = 106.2 N O O RAV = 201.8 N O RAV = 365.72 N RAV = 123.5 N C D…

A:

Q: 4. Use the manning's equation above to find the streamflow rate (Q) under the following conditions:…

A: Manning's Equation: Manning's equation is used to determine the velocity of the flow of the water…

Q: Determine the amount of coagulant required per day (kg/day). • Assume that the optimum dosage of…

A: The optimum dosage of alum = 25 mg/LDensity of alum = 600 kg/m3 Power, P = 1736.3 watt Velocity…

Q: The headwater elevation (HWE) and tailwater (TWE) depths are 4 m and 3.5 m measured above the…

A:

Q: Column ABC has a uniform rectangular cross section with b = 12 mm and d = 22 mm. The midpoint C of…

A: Given : b = 12 mm d = 22 mm Centric load P = 3.7 kN FOS = 3.3 E = 200 GPa This is a problem of…

Q: -5 m- 15 kN/m 5 m- El = constant

A:

Q: The following observations were made during a tensile test on a mild steel specimen 40 mm in…

A: Given data,  Yield load =161 KN  Maximum load = 242 KN  Length of specimen at fracture = 249 mm…

Q: Solve the reaction of shear and moment.   P1= 35   P2=40   P3=30   P4=30   WI=45

A:

Q: Let P = [P] N. m) Determine the magnitude FA of the reaction at pin A. n) Determine the magnitude FB…

A:

Q: Prob. 2. For the rigid frame loaded as shown, determine the reaction components using either the…

A:

Q: Fig subjected shows a brass bar having cross-sectional area of 1000 mm to axial force. Find the…

A: Given data : Cross sectional area = 1000 mm2 Modulus of elasticity of brass = 100 GN/m2 This is a…

Q: 1,0 m * 4 m * 5 m TINININININININ NINI NININIK Dry bark clay y =18 kN/m³ PVP V I 1 I I Sa Ysat =15…

A:

Q: The headwater elevation (HWE) and tailwater (TWE) depths are 4 m and 3.5 m measured above the…

A:

Q: A 32-mm diameter by 3.5-m long steel rod (1) is stress free after being attached to rigid supports…

A: Given data in question  Diameter 32mm Length 3.5 m Elasticity modulus 200 GPa Coefficient of thermal…

Q: HW-4/ For the girder floor beam system shown, find the maximum bending moment at section (1) of…

A:

Q: in the carrying 2,000 mg/L of salts. The salts quickly become uniformly distrib river. A…

A:

Q: Fig. shows a steel bar 900 mm long; its two ends are 40 mm and 30 mm in diameter, the length of each…

A: Given data : Length of steel bar = 900 mm Length of each rod = 200 mm Applied tensile load = 15 KN E…

Q: Situation 6. A simply supported beam loaded by a moment, 8kN.m. clockwise at its left end. The beam…

A: Given: A simply supported beam of 7m span  8KN-m clockwise at left end  EI = 280KN-m²  Required:…

Q: Natural Channels conditions: Gravel beds, straight Gravel beds plus large boulders Earth, straight,…

A: Given data: Top width, B=500 m River depth, y=2 m Bed slope, S=0.01 mm For gravel beds, straight, n=…

Q: 5.) A reinforced concrete The bars cover 1. 2. one greater Compute cantilever beam considered Than…

A:

Q: Use the VIRTUAL WORK method. a.) determine the vertical displacement of joint A. Each bar is made…

A: Given: Required: Vertical displacement of joint A  And why solving reactions of support is not…

Q: W₂=2rad/s A V₂ 3" 8 B Figure 1 TO INFINITY 90° TO INFINITY V F

A:

Q: data for an clay sample are as follows: The laboratory consolidation undisturbed e. e₁ = 1.00, ₁ =…

A:

Q: ● ● Filtration ● ● Assume flow of the filter is V₁ = 7 m³/h·m². Calculate the total area of the…

A:

Q: HW-3/ For the beam shown, find the maximum bending moment at point (c) due to a single concentrated…

A:

Q: -5 @ 3m-15m- C F H J K ML boo I A 4@4m=16m B D G E 60 kips A For the truss shown, what is the force…

A:

Q: 6 ft 2.5 ft O2.93 kips O 4.54 kips O4.84 kips (1) B 3 ft P 8 ft 1.5 ft (2)

A:

Q: Fig shows the bar subjected to a tensile load of 50 kN find: (i) the diameter of the middle portion…

A:

Q: If u = xy + 2y³x. v = -0.5y² + 6x³2 and w = 5y²x - y³z + x, then for a steady and incompressible…

A: Given- Velocity components- u=xy+λy3x,v=-0.5y2+6x3z,w=5y2x-y3z+x, Flow is steady and incompressible,…

Influence Lines

The graphs that show the variation of a function at a specific point on a beam or truss due to a unit load placed at any point along the structure are known as influence lines in engineering. Some common functions that are studied with influence lines are shear, moment, and deflection. In designing beams and trusses, it is important to use influence lines in structures where loads would move along their span such as bridges, crane rails, conveyor belts, floor girders, etc. The influence lines help to study where a load will create the maximum effect for any of the functions.