2. Explain some difference between when to be impedance matching and when there is no impedance matching.

Q: )Determine Zi, Zo, and Av for the network

A:

Q: 4. State the advantages and disadvantages of the three types of amplitude modulation.

A: As per Bartleby guidelines we are allowed to solve only one question, please ask the rest again. The…

Q: For chemicals used in the manufacturing of pahrmaceutical drugs, contamination may occur if a level…

A: Level sensor : level sensor are the device which used to detect level of liquid . Chemical in…

Q: Determine VR1, VR2, VD1, VD2, Vo, I

A: Determine voltage across the resistances VR1, VR2, and diodes VD1, VD2, output voltage Vo, and…

Q: Q52) Use shifting graph to sketch a) y = |(x – 3)2 – 2| b) y = -1+ 5cos (x -)

A: Q52) a)

Q: Calculate the steady-state errors for Types 0, 1 and 2 if the ramp input is applied to the system…

A: In this question we need to find a steady-state errors for Types 0, 1 and 2 if the ramp input is…

Q: Determine vo(t)

A:

Q: Choose the correct Answer: type of a connector is semi precision and provides excellent performance…

A: To analyse the given question

Q: (2BF)16 is between(----------)16 and (--- ----)16-

A: Here the given expression in hexadecimal is Now, first convert this number into decimal number.

Q: mplement the sum of minterm: F(x,y,z) = Σm(1,2,6,7) with a single 1 bit 8-to-1 multiplexer.   clear…

A: To solve above problem, one should have idea about working operation of MUX circuit. MUX is a…

Q: d capacity if the cable is replaced by a coaxial cable with bandwidth (B=500kHz). Assume no and…

A:

Q: Find out what causes the transmission delay and identify the contributing variables.

A: Types of delays Processing Delay Progogation Delay Transmission Delay Queuing Delay

Q: Fill in the blanks with the most convenient answer: The main problem with .... s that control…

A:

Q: For a type-1 system with input ramp signal, the value of steady state error is 0.23.  The value of…

A:

Q: 3. Why this bridge is suited for measurement of high Q ?

A:

Q: B3 Explain the working of the Differential Transformer with transfer characteristics and write the…

A: A Linear Variable Differential Transformer, or LVDT for short, is an electromechanical position…

Q: 4. Two resistors, 25 kN and 75 kN are at room temperature (290 K). For a bandwidth of 80 kHz,…

A:

Q: What are some common methods of impedance matching in audio systems?

A: Explanation: some common techniques of impedance matching in audio systems are 1. Maximum power…

Q: For a twisted pair cable the attenuation measured is 5 dB and the Attenuation to cross talk ration…

A:

Q: USEFUL FORMULA 44 AVE

A: FIND: Forward resistance of given graph

Q: What is the difference between Kirchhoff’s and Nodal analysis.

A: In this question we will find difference between Kirchhoff’s and Nodal analysis....

Q: Loading effect causes inaccuracy in measurement can be avoided by using appropriate instruments or…

A: Accuracy:  It is the degree of closeness between different measured values for a common input value.…

Q: State and prove Baye's theorem

A:

Q: 3- Draw the Experimental setup of the short – circuit Test.

A: The  short circuit test meant for the LV side ( Low voltage side).  The experimental set up can be…

Q: (b) Define Histogram and Frequency Polygons. Write down about the different types of frequency…

A: This question is related to networks.

Q: Variation of which of the following parameter is not consider as power quality problem for industry?…

A: We know that , the power quality parameters described are power, frequency, magnitude of the supply…

Q: Put a true for the correct phrase and a false infront of the wrong phrase, and thencorrect the…

A: Given: Put a true for the correct phrase and a false infront of the wrong phrase, and then correct…

Q: In the given circuit, i(∞) is

A: In this question,  Find the current in the inductor after long time,  Inductor act as short circuit…

Q: Define wy higher on-ofp 1- off ralio. on- Sevies JEFT has ratio compared to shunt as JEFT?

A:

Q: are connect

A: The inverter is a logic gate which invert the input to the output. When the input 0 is given to the…

Q: determine Itotal

A:

Q: Draw the block diagram of sequence detection of 11001.. Showing the inputs and outputs.. Note: "…

A: Block diagram of sequence detection of 11001:

Q: What is meant by impedance matching? Why is impedance matching needed?

A:

Q: (A) Source entropy (B) Joint entropy (C) Receiver entropy

A: Since, we only answer up to 3 sub-parts, we'll answer the first 3.Please resubmit the question and…

Q: y how to covert impedance

A:

Q: Impedance plane is important in ECT, by using diagram briefly explain impedance plane.

A:

Q: A)- Why need Modulation:-

A: In this question we discuss why we need modulation

Q: 1. The load flow data for the sample power system are given below. The voltage magnitude at bus 2 is…

A:

Q: Explain how you would determine the primary and secondary constants of transmission by impedance…

A: The primary and secondary constant of transmission line: A transmission line is a conductive means…

Q: Calculate Theoretical Impedance by formula Z

A: Determine the Theoretical Impedance by formula Z Impedance Z= √(R2 +(XL -Xc)2

Q: Write the nonlinear function to find the ω(lowercase omega) that results in an equivalent impedance…

A: write the equivalent resistance about AB,…

Q: write a loop analysis matrix equations in standard form necessary to solve for any quantity label…

A:

Q: Given the follouin bollowing system, determine the steudy shate error, es, for the hig hest order…

A: The block diagram of a close loop control system is shown. The transfer function for a PID…

Q: Find the general solution with the "Change of Parameters" method.

A: let y=θm y'=mθm-1y"=m(m-1)θm-1 Putting in equation we get,…

Q: Given that for a discrete tine signal a [n a [n] a[o] =5, a[1]=1, a[2]= -3 aL31-1 and for al/ the…

A:

Q: For he circuit shown in the figure below, find Z-Parameters?

A: Circuit diagram is given as ; Circuit can be split into two parts ; And,

Q: The noise level measured at a particular location in a factory with a noisy machine operating nearby…

A: Given parameters are: The noise level measured at a particular location in a factory with a noisy…

Coulomb’s Law

Coulomb's law states that the attraction or repulsion force between two charged things is proportional to the product of their charges and inversely proportional to the square of their distance. It has an effect along the line that connects the two-point charges.