Answered: 2. Flow occurs through a sand-filled…

2. Flow occurs through a sand-filled pipe with a cross- sectional area of 60 cm?. If K is 10 cm/s and the gradient is 0.01, what is the discharge from the pipe?

Principles of Geotechnical Engineering (MindTap Course List)

9th Edition

ISBN:9781305970939

Author:Braja M. Das, Khaled Sobhan

Publisher:Braja M. Das, Khaled Sobhan

Chapter8: Seepage

Section: Chapter Questions

Problem 8.6P

See similar textbooks

Related questions

Q: tank containing water has a total of weight of 75 kg when weighed. Obtain the new reading on the…

Q: The details of a new developed area are given below: Premise Details Houses 2,000 units 2 hotels,…

A: Part A Permises Details Per Unit Water Demand Total water demand Houses 2000 units 300…

Q: The results of an experiment to evaluate the effects of a water reducer are shown in Table P6.32. d.…

A: Water reducing Admixture: Water reducing admixtures are generally added to the mix proportion in…

Q: Solve the reactions for the frame and draw the shear 22 kN/m 18m Dk- 67 kN * 5.4 m 1.8m 37 kN/m. 3.6…

Q: Q2/ choose the right answer 1. Wreckage from the plane was scattered, C) on a wide area. A) over B)…

A: Note- Hi! Thank you for the question, As per the honor code, we are allowed to answer three…

Q: Distinguish between the following terms: a. Sensitivity and detection limit b. LOQ and limit of…

A: Detection limit, as they state very well in another part of the text, is the lowest detectable level…

Q: Modern urban houses such as a terraced houses are made of high thermal mass structure. Under the hot…

A: Three factors that influence the performance of natural ventilation in terraced houses located in…

Q: the value of degree of saturation Specific gravity32.7 void ratio=0.34 water content=0.23

Q: Moment Area Method 1. Estimate the deflection at point C and the rotation at point B. EI is…

A: Given data: k is kilo pounds. E=4000 ksi I= 2000 in4.

Q: g on the x face of a stress element are ox nd Txy ange of values for the stress oy if the near…

A: σx=5900psiσy=?τxy=1950psiWe knowRadius of mohrs circle =τmax

Q: If the 5kg block is suspended from the pulley B and the sag of the cord is d 0.15 m. Draw (FBD) and…

Q: The size of a shovel is indicated by what? O a. Size of bucket, cu.ft. O b.Size of engine,…

A: Correct answer :- (c) Size of bucket , Cu.Yd Explanation:- The size of a power shovel is…

Q: determine the maximum displacement of the beam in the figure shown .

Q: em II. The figure below shows the cross-section of a thin-walled shaft subjected to a torque MT =…

A: Given:- a=200mm MT=100kN-m t=20mm G=77.2GPa allowable shear stress=200MPa To find:- a) shear stress…

Q: Solve the reactions for the frame and draw the shear & moment diagram for each member 22 kN/m 1.8 m…

Q: A half-closed clay layer is 8 m thick and it can be assumed that cv ¼ ch. Vertical sand drains 300…

A: The given data is: Clay layer thickness=8 m Sand drains diameter=300 mm sand drains spacing=3 m

Q: The measured extreme fibre strains at mid span of a simply supported beam, loaded with uniformly…

Q: Determine the value of degree of saturation Specific gravity32.7 void ratio=0.34 water content3D0.23

A: Given data : The value of water content w=0.23 The value of specific gravity G=2.7 The value of void…

Q: The grain of the wooden member forms an angle 15° with the rertical. For the state shown in Figure…

A: σx=0σy=0τxy=400psiRadius of the…

Q: 120 mm 100 mm A load P =40 kN axial load is applied to a short wooden post that is supported by a…

Q: For the beam with cross-section shown, the allowable flexural stresses for tension and compression…

A: Maximum flexural stress occurs where maximum bending moment occurs. In Postive bending moment,…

Q: Problem (7,2): The surface of an airplane wing is subjected to plane stress with normal stresses a,…

Q: 20. Determine the numerical value of the factor (A/P, 5%, 10). 7.7217 B 0.0795 c 0.1295 12.5779

A: There are different types of factors which are used to calculate the future value of the amount. For…

Q: 2. When compounded quarterly P12,000 becomes P 20,415.23 after 4 yrs. What is the nominal rate of…

A: step 1-

Q: primary treatment secondary treatment aeration tank disinfectant raw sewage secondary clarifier…

Q: SITUATION. A pressure vessel 300 mm in diameter is to be fabricated from steel plates. The vessel is…

Q: Find the value of discahrge through rectangular cross section having area 1.3 m2 and velocity of…

A: Introduction : The given question is related with fluid mechanics . In this question we are provided…

Q: 140 mm 140 mm A centric load P is applied to the granite block shown. Knowing that the resulting…

Q: 1. Calculate the design moment capacity þMn of the beam if fc 28 MPa and fy = 420 MPa 2. Check…

Q: 120 mm 100 mm A load P = 41 kN axial load is applied to a short wooden post that is supported by a…

A: Load, P = 41 KN ( axial compression) Cross sectional area, A = 120*100mm2 Determine bearing stress =…

Q: Which of the following are factors that are involved in transportation (vehicle) accidents/crashes.…

A: Vehicle accidents/crashes- It is an unfortunate mishap in which a vehicle hits a person, object or…

Q: SITUATION. The beam shown is subjected to a uniform dead load of 1.2 kN/m, a concentrated dead load…

Q: A flat circular plate lies in the horizontal (xz) plane and is supported at the three…

Q: The connected chain or chains of critical activities or zero float activities, extending from the…

Q: A solid sphere (diameter 6 mm) is rising through oil (mass density 900 kg/m3, dynamic viscosity 0.7…

Q: Let P = 6 kip-ft. 60 kips w = 4 kips/ft B. 12 kips Pkip-ft Draw the shear and bending-moment…

Q: Q.3 Select the word (advantage) or the word (disadvantage)) of the flowing expressions; Advantage…

A: in this question four statement is asked weather they are having advantage or disadvantage three…

Q: Q.3 Select the word (advantage) or the word (disadvantage)) of the flowing expressions; Advantage…

A: Given, There are multiple questions are posted in a single picture. Our aim is to Select whether…

Q: / Draw Shear and Moment Digram for this Cantilever beam show below 4 KN 4 KN/m 2 KNOM 4 m.

A: Intensity of UDL = 4 kN/m Intensity of point load = 4 kN Couple moment (M) = 2 kN-m span of beam…

Q: what does a 300 x 300 column (for three storey) should looks like. this is for the details of…

A: Detail of any rcc component of structure shows mainly the dimensions of component and detail about…

Q: What is the main working member of a grader? Oa. Moldboard O6.0perator Oc. Large tires. Oa.Engine

A: Grader is a heavy machine which used in the road construction .

Q: For the beam with cross-section shown, the allowable flexural stresses for tension and compression…

Q: 13. Determine the numerical value of the factor (A/F, 5%, 10). 0.0795 B 12.5779 A 0.1295 D 7.7217

A: Answer is A) 0.0795

Q: -1.5 m→| C В 'A 3 m

Q: 8

A: Given data- Gage Length of brass(L) = 50 mm Diameter (D) = 10 mm Tensile load (P) = 20k N Increase…

Q: A strip footing of width 3 m is founded at a depth of 2 m below the ground surface in a (c - 0) soil…

Q: smooth 2 kg collar shown in the figure is attached to a spring having a stiffness k=3 N/m and an…

A: mass of collar = 2 kg

Q: 0.2: Consider the cantilever beam subjected to the concentrated load shown below The cross section…

Q: A 2 lane highway with a grade of 6% has a posted speed limit of 50 mph and a design speed of 55mph.…

A: The stopping sight distance (SSD) : The stopping sight distance (SSD) is the minimal sight distance…

Q: 4. A manufacturer of off-road vehicles is considering the purchase of dual-axis inclinometers for…

Question

2. Flow occurs through a sand-filled pipe with a cross-
sectional area of 60 cm?. If K is 10 cm/s and the
gradient is 0.01, what is the discharge from the pipe?

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

Q1: (a) Define and explain uniform flow. How is open channel flow different from pipe flow? (b) Under what conditions the bed slope, water surface slope and the energy line slope are equal?
Consider a 20-ft wide rectangular channel with a Manning's n value of 0.03. The channel has a discharge of 200 cubic feet per second at a uniform flow (normal) depth of 2 ft. A sluice gate at the downstream end of the channel controls the flow depth just upstream of the gate to a depth z. Determine the depth z so that a hydraulic jump is formed just upstream of the gate. What is the head loss (energy loss) in the hydraulic jump?
Assume uniform flow through a half-full circular channel. a. hydraulic radius (m) b. Reynolds number c. hydraulic depth (m) d. Froude number
Water is flowing in a 5 m wide rectangular channel at a depth of 360 mm. A hydraulic jump occurs and the depth of water downstream from the jump is 1300 mm. Determine the discharge.
Water depths in the upstream and on the crest of a hump were measured and they were 1.65 m and 0.435 m. Assuming that the choking effect already occurred on the hump and energy losses are negligible, what is the specific discharge and hump height in the channel? ( Show calculations and sketch) a) 0.9 m2/s and 1 m b) 1 m2/s and 0.9 m c) 1.2 m2/s and 1 m d) 1 m2/s and 1.2 m
What will be the discharge of a closed conduit 1 m in diameter if it is ¼ full and the velocity of flow in the conduit is 10 m/s?
The incoming flow rate is 100 m3/s on a rectangular channel with: depth = 3 meters width = 4 meters Then, a hydraulic jump occurred along the way. Determine the depth at the hydraulic jump section.
Determine the velocity of flow after hydraulic jump through a 1 m wide channel if the velocity of flow before jump was 2 m/s and the depth was 0.2 m.
A trapezoidal channel of 2.0m bed width and 3:2 side slope carries a discharge of 10m3/sec with a depth of flow of 0.5m. Determine whether the flow is supercritical or subcritical. If hydraulic jump where to form. what would be its height and efficiency. Assume mannings coefficient n = 0.025
For the three-reservoir problem shown , the flow through pipe 2, from Dto B, is 3.0 CFS. a) Find the head loss in PIPE 2. b) Determine the flow in pipe 3 (in cfs) and is directed from where? c) What is the length(in feet) of pipe 1 from reservoir A?
A stream having a discharge of 280L/sec per meter width of channel has a depth after the jump of 90 cm. a. What is the velocity of water before the jump? b. What is the head lost in the jump?
Water flows in a rectangular open channel of constant width at a velocity of 0.8 m/s and 1.6 m depth. After a certain hydraulic structures the depth was measured to be 1.2 m. Calculate the flow velocity at downstream of the hydraulic structure.