2. If the allowable shear stress for each of the steel pins at A and B is tpe 6.5 ksi and the allowable normal stress for bar CB is Operm 10 ksi, determine the diameter of the pins at A and B and that of the square bar CB. Pin A is in double shear while Pin B is in single shear. Ignore points D and E. (^ )

2. If the allowable shear stress for each of the steel pins at A and B is tpe 6.5 ksi and the allowable normal stress for bar CB is Operm 10 ksi, determine the diameter of the pins at A and B and that of the square bar CB. Pin A is in double shear while Pin B is in single shear. Ignore points D and E. (^ )

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter7: Analysis Of Stress And Strain

Section: Chapter Questions

Problem 7.2.12P: Solve the preceding problem if the norm al and shear stresses acting on the element are sx = 2100...

See similar textbooks

Similar questions

.4 The stresses on an clement arc known to be sx= 120 MPa, sy= 100 MPa, and txy= 75 MPa. Find the stresses on an inclined section through the element at an angle ? = 45°.
A thin-walled rectangular tube has uniform thickness t and dimensions a x b to the median line of the cross section (see figure). How does the shear stress in the tube vary with the ratio = a/b if the total length Lmof the median line of the cross section and the torque T remain constant? From your results, show that the shear stress is smallest when the tube is square (ß = 1).
Solve the preceding problem if the norm al and shear stresses acting on the element are sx = 2100 kPa, sy= 300 kPa, and txy= -560 kPa, and the seam is oriented at an angle of 22.5° to the clement.
A tie-down on the deck of a sailboat consists of a bent bar boiled at both ends, as shown in the figure. The diameter dBof the bar is 1/4 in., the diameter D Wof the washers is 7/8 in., and the thickness is of the fiberglass deck is 3/8 in. If the allowable shear stress in the fiberglass is 300 psi, and the allowable bearing pressure between the washer and the fiberglass is 550 psi, what is the allowable load P allowon the tie-down?
A pole is fixed at the base and is subjected to a linearly varying distributed force with maximum intensity of q0and an axial compressive load P = 20 kips at the top (see figure). The pole has a circular cross section with an outer diameter of 5 in. and an inner diameter of 4.5 in. Find the normal stresses on the surface of the pole at the base at locations A and B.
Two forces, each of magnitude P, are applied to the wrench. The diameter of the steel shaft AB is 17 mm. Determine the allowable value of P if the shear stress in the shaft is not to exceed 134 MPa. Use G = 80 GPa for steel.
Compute the maximum vertical force F that can be applied at A, if the shearing stress in the pin at O and the axial stress in rod BD are limited to 4000 psi and 1000 psi, respectively. The diameters are 0.25 inch for the pin, and 0.5 inch for the rod. Assume single shear for the pin. Answer: F = ___________________
A shaft composed of three segments and fastened to rigid supports. Determine the maximum shear stress developed in each segment. (Please don't skip any mathematical step and please show all the working)
For the connection shown, the bolt diameter is d = 30 mm. The average shear stress in the bolts must be limited to 160 MPa. Determine the maximum load P that may be applied to the connection based on the shear strength of the bolts.
A simple truss is subjected to a vertical load F = 500 lb.Determine the minimum diameter of the pin at C if theallowable shear stress on the pin is 20 psi.Answers: d =___________________
The drive shaft AB of an automobile is made of a steel having allowable shear stress of tallow = 8 ksi. If the outer diameter of the shaft is 2.5 in. and the engine delivers 200 hp to the shaft when it is turning at 1140 rev>min, determine the minimum required thickness of the shaft’s wall.
The cross-sectional area of bar ABCD is 600 mm2. Determine the maximum normal stress in the bar.