A couple is applied to the beam as shown. What is the magnitude?

Q: Q2 A beam of 4-m span is in the form of a cross bar as shown in Fig. (2) It carries a uniformly…

A:

Q: Q.5 (20%) Determine the reactions in C on member BCD as shown in figure? 6 m 4 m D 2 m 300 kN

A: Detailed explanation and solution of the above problem uploaded in below pictures.

Q: In a certain locality the drybulb temperature is 35 C & the relative humidity is 70 %. At normal…

A: Given question is

Q: The gravity acceleration at a certain level is 9.78 m/s². This accelartion varies by 8.28 x 104 m/s²…

A: Given data: g=9.78 m/s2 Need to determine the weight of the object and height of the required point.

Q: Q3- For the truss shown in Figure (3), determine the forces in members BK, CD and DK. 20 KN 40 KN 20…

A:

Q: A steam pipe line of 150/160 mm in diameter is covered with layer of heat insulating material of…

A: Write the given data. d1=150 mm, r1=75 mmd2=160 mm, r2=80 mmd3=160+2×100=360 mm, r3=180 mmk=50…

Q: Q5: The gas CO₂ is diffusing at steady state through a tube 20 cm long having a diameter of 1cm at…

A: Given: The length of tube, L = 20 cm The diameter of tube, d = 1 cm The temperature, T = 350 K The…

Q: B/ Determine the resultant of the force system shown in Figure (IB) and show it on a sketch with…

A:

Q: At what angle @must the 430-Ib force be applied in order that the resultant R of the two forces have…

A:

Q: 2. (a) Replace the force system acting on the post by a resultant force and (b) couple moment at…

A: Given P = 260 lb M = 500 lb Force at point = 50 lb To find Replacement force Moment at point O…

Q: A closed vertical cylindrical vessel, 1.75 m in diameter and 3.5 m high is 75% full of oil (SG=0.8)…

A: given; diameter ofcylinder(d)=1.75mradius of cylinder(r)=1.75m2…

Q: Find the Diameter of the shaft

A:

Q: Weather radar provides information on the intensity as well as the total amount of precipitation.…

A: Given Data Reflective value at which the value need to calculate is: RV=47 dBZ The amount of time…

Q: 5. A transmission tower is held by three guy wires attached to a pin at A and anchored by bolts at…

A: Given: The tension in wire AB, TBA = 110 lb

Q: 1. Yilt) Ki M fit) # M₂ Yalt) K₂ Fr B2

A: Given,

Q: ) In cooling tower below, derive the given equations based on the system boundary below (neglect…

A:

Q: Data: Hp2,3 = 2 m; A3 = 20 cm²; A₂ = 1 cm²; Hp0,1 = 0.8 m; NB= 74%(pump efficiency) To determine:…

A:

Q: A prototype submarine moves at velocity V, in fresh water at 20 °C, at a 2-m depth, where ambient…

A: Given    Depth, h = 2 m Pressure, P = 128 kPa Cavitation number, Ca = 0.25 Find   Velocity, v

Q: 6. A force P of magnitude 330 lb acts on the frame shown at point E. (a) Determine the rectangular…

A:

Q: Q.6 Determine the force in members ac,be,ce,ei & gh of truss shown in figure 3m + 3m 4m h 11 g + 4m…

A: GIVEN DATA - A PLANE TRUSS GIVEM WE HAVE TO FIND FORCES IN GIVEN MEMBER CONCEPT USED-METHOD OF JOINT

Q: Q: Draw the shear force and bending moment diagram for the beam shown in Fig. and find maximum shear…

A: Given: To Find:  1) Shear Force and Bending Moment Diagram 2) Maximum shear force and bending…

Q: What are the two main types of characterization of smart materials? Using as few words as possible,…

A: There are two main types of characterization of smart materials are given as under,

Q: Q1: Find the Diameter of the shaft made of A cold-drawn steel. Assume that ultimate stress is 370…

A: Given: The ultimate stress = 370 MPa The factor of safety, n = 3 The tension in the loose side, T2 =…

Q: Find Ratio of specific heats of CO2 at 825K and NO2 at 825K.

A: To determine:- Ratio of specific heats of CO2 and NO2 at  825 K

Q: Explain about availability in thermodynamics in detail.. like formulas and when it's applicable and…

A:

Q: " 12 13 30° F₂= 200 N 5 F3 = 260 N the magnitude of the resultant force acting on the bracket is to…

A: Write the algebraic sum of forces in x-direction.…

Q: Determine the components of the force F perpendicular and parallel to the post.

A:

Q: Q3) Compute the horizontal and vertical components of the water pressure acting on the face of…

A: Given data: ● The included angle of tainter gate AB:  θ = 72° ● The radius of the sector of the…

Q: Q6: Design a cast iron piston for a single acting four stroke engine for the following data: Maximum…

A: Given: Maximum gas pressure→P=5MPa Cylinder bore→D=100 mm=0.10 m So the area of…

Q: Q2) A cylindrical body of length 0.9 m and of sp.gr = 0.7 is floating in water as shown in fig.2.…

A:

Q: Using the equations for the Barometric Law and temperature decrease from adiabatic expansion (found…

A: Given Data h=5km T=288K γ=1.4 Using the Barometric Law as Follows

Q: Two reversible cycles are in series, each process doing the same net work, Wcycle. The first cycle…

A: Given data: Higher temperature (TH)=1000°RLower temperature (TL)=400°R Need to determine the…

Q: In a diesel cycle, what is the expansion ratio if the % clearance is 1/16 while the cut-off ratio is…

A: Given:-  In a diesel cycle,  % clearance (c) = 1/16 Cut-off ratio = 2.7 To Find:-  Expansion ratio…

Q: The geared system shown in Figure P3.19 represents an elevator system. The motor has an inertia I,…

A:

Q: Q3- For the truss shown in Figure (3), determine the forces in members BK, CD and DK. 20 KN 8 Dimine…

A:

Q: Are surface-hardened parts always case-hardened by carburizing?

A: The case hardening is a process in that a thin layer of surface is hardened. This thin layer is…

Q: Calculate the magnitude and location of the resultant of uplift pressure. 1. Magnitude = KN use 3…

A: We can answer up to 3 subparts so we will answer first 3. Please resubmit the question by specifying…

Q: A piston cylinder containing air receives 3.892kw heat at constant temperature, and an initial…

A:

Q: Radiation heat transfer occurs in an object that should place in vacuum space. (True or False) False…

A: Radiation Heat transfer doesn't require any medium. It can happen in vacuum too.

Q: Direction: Solve the following problems neatly and systematically and include free body diagrams.…

A:

Q: At 68 ̊F water has a dynamic viscosity of about 2.11 x 10^-5 lb-s / ft^2, solve the kinematic…

A:

Q: SITUATION C. A closed vertical cylindrical vessel, 1.75 m in diameter and 3.5 m high is 75% full of…

A:

Q: A A moment diagrams. Neglect the weight of the beam. Wo L Problem 1 L Problem 3 A B Wo 2 m B Co -80…

A:

Q: For the truss loaded as shown, determine the equation for the line of action of the stand-alone…

A:

Q: 2- In order to determine the effects of a force. A. magnitude of the force B. line of action. nature…

A: When a force is acting on body, it effects the body as if the body is at rest than body start moving…

Q: Given oil, S=0.82 find: Specific weight in lbs/ft^3 Density in slug/ft^3

A:

Q: In air pipline, the flow has the following conditions at section 1: 25C. 1.8 bar, 15 m/s velocity,…

A:

Q: The outer surface of an oil heater at a uniform temperature of 100°C is to be filled with straight…

A:

Q: Four people are attempting to move a stage platform across the floor. If they exert the horizontal…

A:

Q: What is the control plane's principal function?

A: Introduction: In a network there are various planes have different works. Every plane or part of…