2. In a two ram hydraulic steering gear the diameter of the rams is 280mm,diameter of the rudder stock is 350mm,distance from rudder stock center to center line of rams is 860mm and the maximum angle is 35 degrees. Find the pressure to limit the shearing stress to 77MPa

2. In a two ram hydraulic steering gear the diameter of the rams is 280mm,diameter of the rudder stock is 350mm,distance from rudder stock center to center line of rams is 860mm and the maximum angle is 35 degrees. Find the pressure to limit the shearing stress to 77MPa

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Related questions

Q: A steel rod with a cross-sectional area of 0.25in .^ 2 is stretched between two fixed points. The…

A: GivenArea of cross section A=0.25 in2The tensile load at 70oF is =1200 lbthe stress at 0oF…

Q: FIGURE 4.13 Figure for Problems 4-3 and 4-4. 4-3 Shown in Fig. 4.13 is a vertical-walled storage…

A: (a) Volume stored is calculated as: V=Net volume flow rate ×TimeA×h(t)=(q0-qout)th(t)=(q0-qout)tA…

Q: 5.111 A window awning is fabricated from sheet metal with a uniform thickness. Locate the center of…

A: Divide the given window into the different parts as shown in the figure below :

Q: Using the equation Kica, plot the fracture stress (MPa) for aluminum alloy 7075-T651 versus surface…

Q: 3. For the canal gate shown, sketch the pressure distributions applied to it. Sketch the resultant…

Q: Which of the followings is NOT correct: Fatigue limit is just for ferrous materials (such as steel)…

A: The fatigue limit is defined as the value of stress below which the fatigue failure does not take…

Q: A boiler is being fed by a conical tank seen in the figure. The piping between tanks is through a…

Q: A student wants to launch a golf ball into a 3rd floor window, located 7m above ground level. The…

Q: ma 1- A LOAD CELL IS SCALED 4.20mA = 0-20,000 LB WHAT IS THE WEIGHT AT 14.6 m A ? 11.6mA-ARA = 10.6…

Q: Give the required I, for a simply supported beam 20' long with a uniformly distributed total service…

A: Given data Length = 20' Load = 800(lb/ft) Find the required moment of inertia

Q: Air contained in a piston-cylinder assembly undergoes the power cycle shown in the figure below. n =…

A: According to the given data P1=4.5bar P2=1.2bar v1=v3=1m3/kg v2=3.75m3/kg We need to find Thermal…

Q: Steel shaft AD (G = 80 GPa) is subjected to torsional loads at sections B and D, as shown in the…

A: To Find : The amount of torque T D φ C added at D that would make the rotation at C equal to zero,…

Q: The water in a tank is pressurized by air and the pressure is measured by a multifluid manometer as…

A: Givenh1=0.2mh2=0.3mh3=0.4mρw=1000 kg/m3ρo=850 kg/m3ρhg=13600 kg/m3

Q: A pump is to deliver 80 gpm of water having specific volume of 1.0164x10-3 m3/kg at a temperature of…

A: According to the given data Discharge (Q) = 80 GPM = 0.1337×8060 =0.1783 ft3s =308.045 in3s At T =…

Q: For the machine element shown, locate the y coordinate of the center of gravity. Given: /= 1.5 in. 4…

A: The radius to small circle is r=1.5 in

Q: The system shown below is subject to a sinusoidal base excitation with an amplitude of Y and…

A: Given: Here is the given data, M=10 kgc=472 N·smK1=17 kNmK2=3K1 kNm=51 kNmΩ=300 rpm To find: The…

Q: Note: m = 5 kg Solve the transfer function T(s) = x2/F(s) if b1 = 2, b2 = 4, K1= 5 and k2 = 7 k₁ ww…

A: The values are m=5 kg, b1=2, b2=4, k1=5, k2=7

Q: A 240-kip concentric load P is applied to the granite block shown. 6. 6 m. Determine the resulting…

Q: A statically determinate three-hinged arch is shown below, L = 1.5 m and P = 3 kN. Compute the…

A: (a) Draw the free-body diagram of the beam.

Q: A bar with varying cross section is subjected to various forces as shown below. Compute: a) Stresses…

A: Given Data- E=2.1*10^5 N/mm2 P1=17KN , P3=38KN , P4=21KN We have to find a) stress in each section…

Q: 13-13. An L-2 steel link in a forging machine is pin connected to the forks at its ends as shown.…

A: Given: An L-2 steel link in a forging machine is pin connected to the forks at its ends as shown.…

Q: Steam enters a turbine with a mass flow rate of 15 kg/s at 500°C and 8 MPa. 30% of the steam is…

A: Steam turbine is adiabatic Mass flow rate = 15 kg/s T1= 500°C P1= 8 MPa steam is removed from the…

Q: 4. Determine the maximum normal stress developed in a bar when it is subjected to an axial load of P…

Q: 4. The F-shaped assembly is welded to collar A that fits frictionlessly on the vertical pin that is…

Q: a. Determine the diffusion coefficient for zinc diffusing into copper at 200°C. b. Create a plot…

Q: A single crystal is oriented such that the normal to the slip plane is at an angle of 65°. Three…

A: The given information in the problem is shown in the following attached image:

Q: A heater coil is completely immersed in an oil bath that is insulated on all sides except for the…

A: a) Here's a schematic of the system: Heat transfer rates: Heat transfer from the coil to the…

Q: A vector field S is expressed in rectangular coordinates as: 76 (x − 1)² + (y − 2)² + (z + 1)² S=…

A: Given: S=76x-12+y-22+z+12x-1i+y-2j+Z+1k P = P=3,-1,4

Q: 1.C3 Two horizontal 5-kip forces are applied to pin B of the assembly shown. Each of the three pins…

A: Given: To find: Program to find normal, shear, bearing stresses Permissible diameter

Q: rque Problem diagram below shows the lower leg being held in a stationary. The torque ng to turn the…

A: Angle made with horizontal = 50° Weight of leg WL = 90 N Weight of barbel Wb = 120 N Quadriceps…

Q: *4-104. Replace the force system acting on the post by a resultant force and couple moment at point…

Q: Determine the volume and the surface area of the half-torus shown in the figure. VI

A: It is needed to determine the area and the volume of the half torus. Consider the diagram as shown…

Q: Using Castigliano's method, determine the deflection at point B for the beam shown below. M A a

Q: You want to stop the acceleration of the boxes in the figure above by applying an additional force…

Q: 6 kN 45° 5 kN C B A 45° 6 kN 5 kN 10 kN 0.75 m 1.50 m 1 m

A: Given data E= 200GPa Yield strength = 345 MPa Find the displacement of point B and A

Q: Problem 2: For the beam and loading shown: 1) determine the reactions at A and B, 2) draw the shear…

Q: Find the moment about point A due to the forces shown in the Figure below. HINT: Choose clockwise as…

A: According to the given data A force system is given in the question We need to find Moment about -A…

Q: The condensing pressure for a Rankine engine is 0.001325 MPavac. Calculate the following for steam…

A: “Since you have posted a question with multiple sub parts, we willprovide the solution only to the…

Q: A block and sphere are connected by a cord that passes over a pulley as shown. Neglect friction and…

Q: A fireworks shell P is launched determine the values of r and upward from point A and explodes at…

Q: A straight length of copper steam pipe 450mm long connects two components. Find the stress in the…

A: According to the given data E=103Gpa L=450mm α=1.7x10-5/°C ∆T=140°C δ=0.8mm We need to find Stress…

Q: The part view should be the same as picture. 2- The color is RGB as 0,220,100. 3- Should use the…

A: Find Draw the given object using the drawing.

Q: State Bernoulli's theorem for steady flow of an incompressible fluid. From first principles, derive…

A: Bernoilli's Theorem:- The Bernoulli principle describes how the pressure of a moving fluid relates…

Q: What is the maximum time (in hours, nearest hundredths) a glider can achieve over the ground if it…

A: Solution: Given Data: H=4011 mW=2663 NA=16.1 m2CD=0.011 + 0.026CL2ρ=1.225 kg/m3cos γ=1 To Find:…

Q: A drawbridge is being raised by a cable El. The four joint loadings shown result from the weight of…

Q: A steady, three-dimensional velocity field is given by V = (0.657 +1.73x +0.948y+as) + (2.61 +cr…

Q: A ball is thrown vertically up with a velocity of 29 m/s at the edge of a 77-m cliff. Calculate the…

Q: A tank with a concrete basin is shown in the figure and is filled with water to a height h. Openings…

A: The volume of the tank is Vwater=Vbase+wh2 Vbase=144 ft3, w=100 ft The flow rate of water…

Q: Given: N1 = 10, N2 = 20, N3 = 30, N4 = 40 J1 = 1, J2 = 2, J3 = 3, J4 = 4, J5 = 5, D1 = 1, and D2 = 2…

A: θ1sT1s

Q: Problem 5.1 When a liquid flows over a surface, the velocity may vary with position. The equation or…

Concept explainers

Power Transmission Elements

It is defined as the energy transfer from one location to another location. The energy will start moving from the energy generation source to the energy applied position to obtain the work output. From this method, a large amount of electric energy moves from the power station to various electrical substations.

Question

In a two ram hydraulic steering gear the diameter of the rams is 280mm, diameter of the rudder stock is 350mm ...

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Design of Power Transmission Elements and Power Transmission Systems

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Please solve all I give thumb up A drive system consists of single strand chain running on a 22 tooth drive sprocket at 1600 rpm. The pitch of the chain is 1/2". The driven sprocket and shaft must turn at 280 rpm. Using center distance = D + (0.5)d, find the a) required number of teeth on driven sprocket b) sprocket pitch diameters (driver and driven) c) total chain length in inches d) chain velocity in feet per minute
Two parallel shafts have an angular velocity ratio of 4 to 1 are connected by gears, the largest of which has 40 teeth. Find the number of teeth of smaller gear.
1. A pair of 20 degree full depth spur gears have module of 2.5 and to be mounted on shafts with center distance of 90mm and gear ratio of 3. Determine: a. If there is interference b. If the center distance was increased by 3mm, find the backlash produced c. length of action and contact ratio
A roller chain is to transmit 5 hp from a gearmotor to a wood-working machine, with moderate shock. The 1-in output shaft of the gearmotor turns n = 500 rpm. The 1 ¼-in. driven shaft turns 250 rpm; C »16 in. (a) Determine the size of sprockets and pitch ofchain that may be used. If a catalog is available, be sure maximum bore of sprocket is enough to fit the shafts. (b) Compute the center distance and length of chain. (c) What method should be used to supply oil to the chain?
A worm gear reducer is driven by a 1200 rpm motor. The worm has 3 threads and the gear has 45 teeth. The circular pitch of the gear is p=0.5”, the center distance is 4.5 inches, the normal pressure angle is 20 degrees, and face-width of the gear is b=1 inch. Use a coefficient of sliding friction of 0.029. Determine:a. Gear and worm diameters, and worm Lead.b. The worm gear efficiency
For a pair of standard gears, the module is m=2.5mm，pressure angle is α=20 0. ha*=1. c*=0.25. The teeth number on gear 1 is z1=22. The standard center distance is a=68.75mm. If the actual center distance is a’=69.75mm, find the working pressure angle α’=( )°
The pitch circle diameter of the smaller of the two spur wheels which mesh externally and haveinvolute teeth is 100 mm. The number of teeth are 16 and 32. The pressure angle is 20° and theaddendum is 0.32 of the circular pitch. Find the length of the path of contact of the pair of teeth.
A pair of 20 degree full depth spur gears have module of 2.5 and to be mounted on shafts with center distance of 90mm and gear ratio of 3. Find : $ if there is an interference $length of action and contact ratio $ if centher ditance was increased by 3mm, find backlash produced
A 20-teeth sprocket driving a 100 teeth sprocket with a center distance of 38 pitches. Find the chain length required to avoid the use of an offset link.
In a single-stage gear wheel system with an evolvent profile, the rotating (driveThe number of teeth of the gear is Z1=10, the number of teeth of the rotated gear is Z2=20 and the modulus is m=5 mm; The rotating gear rotates clockwise. d) Prevent undercutting, if it exists on the same shape, by enlarging the grip angle. Calculate the value of the new grip angle and compare it with the new grip angle value you obtained from the drawing.
4. A 6 pitch bevel gear has diameter of 8” while its pinion diameter is 4” with tangential force of 200lb . If pitchlinevelocity is 600ft/min. Determine length of cone, face width, working depth, total depth,and dynamic load.
a double threaded worm gear transmits 15 Hp at 1150 rpm. the pitch of the worm is 0.75" and pitch diameter is 3". the pressure angle is 14.5 degrees and coefficient of friction is 0.12. Find the worm gear efficiency