2. The hinged component shown in Fig. 2 is used to activate a latching device for securing a large trailer body to its undercarriage. If a tension T = 400 N is required in the horizontal control rod to trip the plunger against which the component acts at C, estimate the force supported by the pin at A. [Ans - 458 N ]

2. The hinged component shown in Fig. 2 is used to activate a latching device for securing a large trailer body to its undercarriage. If a tension T = 400 N is required in the horizontal control rod to trip the plunger against which the component acts at C, estimate the force supported by the pin at A. [Ans - 458 N ]

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter10: Virtual Work And Potential Energy

Section: Chapter Questions

Problem 10.62P: The bar ABC is supported by three identical, ideal springs. Note that the springs are always...

See similar textbooks

Similar questions

A uniform horizontal pipe weighing 10 kg and 1.5 m long is used as a lever. If you need to balance two objects (one on each end), where should the fulcrum be placed? The objects weigh 25 kg and 52 kg. What is the reaction force exerted by the support on the pipe? Draw the complete diagram to describe your final answer (include the lengths).
A ball of mass mand radius Rrests at the edge of a step barrier of height has shown in thefigure. There is a horizontal force Tapplied to the ball from its top through a string wrapped around the ball to lift it above the barrier as shown in the figure. What is the minimum tension required to begin to lift the ball off the ground? (g = 9.8 m/s2, m = 1 kg, R = 0.5 m, h = 0.2 m).
Gate AB retains water as shown in the figure. The gate is supported every 2 m (perpendicular to the plane of view) by member BC, which is attached to a 2000 kg mass at point C. What minimum static coefficient of friction μs, along the contact surface between the mass and its base, is needed for the gatestructure to be in equilibrium? There are pins at pointsA, B, andC.
The front view of a Zenith CH 750 Cruzer airplane named "Mapanikwa" is shown in the figure below. The wing AE is supported by the lift strut BC and is connected to the fuselage by a lug attachment at point A that may be idealized as a pin. The lift strut is a two-force member in equilibrium and is also pin-connected at points B and C. The vertical distance from the pin at A to the pin at C is 1.2 meters. A 1,500 lb upward force caused by the lift generated by the wing is acting at point D. If point B is equidistant from the pin at A and the wing tip E, and if the distance X is equal to 0.5 meters, determine the force supported by the pin at A.
Question If you used an ideal pulley of the type shown in picture (a) to support a car engine of mass 145 kg , (a) What would be the tension in the rope? (b) What force must the ceiling supply, assuming you pull straight down on the rope? The pulleys system mass is 5.50 kg
The corener of a sheet with mass 3kg hangs at the centre of a 30 m long clothing line whose ends are fastenend to poles 18 m apart. Draw a vector diagram and determine the tension in each portion of the clothing line. ***Diagram attached.
The mechanism shown consists of a crank (bar AB), a connecting rod (bar BC) and the piston C that slides on the smooth surface (without friction). The combustion of gasoline produces a force P on the piston and this is kept in equilibrium with the moment M applied in A. The length of the crank is 116 mm, the length of the connecting rod is 183 mm, the force P is 710 N and the angle theta is 0.56 radians. Determine the value of M in Nm.
A 30kg mass is tied to a uniform rod whose mass and length are 80-kg and 8-m, as shown below. The rod is attached to the floor via a hinge and makes an angle of 70° relative to the ground; a massless string is also attached to the rod at the ¼ point of the rod and makes an angle of 20° relative to the horizontal. What tension must be provided by the rope so that the system remains in stationary? If at some point the string breaks, what will be the angular acceleration of the system the instant that the string breaks?
In order to burgle a local McDonald's, the Hamburglar must climb onto the roof. To do this, a ladder of length 3.31 m and mass 21.2 kg is placed leaning against a vertical wall, as shown in the image below. There is negligible friction between the ladder and the wall, but the same is not true for the ladder and the ground: us ≠ 0 between those two surfaces. Even with that friction, the ladder will start slipping if the angle ø ladder makes relative to the ground is less than 71.0°. Assuming the ladder is uniform (so that its center of gravity is located at its geometric center), what must be the maximum static frictional force (in N) that exists between the bottom of the ladder and the ground? Explain how you solved the problem involving a ladder leaning against a wall. Be sure to state what your known and unknown quantities are, what concepts were applied, and what equations were used!
A uniform ladder, 4.8 m long and weighing 220 N, rests against a smooth vertical wall. By taking moments about lower end of the ladder, which is 1.5 m from the wall, calculate the horizontal reaction of the wall on the ladder. Take the weight of the ladder as acting at its mid-point. Also, find the magnitude and direction of the reaction at the floor.Note: Show a free-body-diagram and all your workings.
Two weights, A and C, are fixed to a bar, B. Their masses are: A = 60 kg, B = 230 kg,C = 45 kg. B is, in turn, connected to a fixed vertical post by a hinge and a support cableD. The geometry of the system is shown at right. Treat weights A and C as point masses a)What is the tension in support cable D? Be sure to include a detailed freebody diagram to accompany your analysis.b) What is the magnitude of the force provided by the hinge?c) What is the moment of inertia of the A + B + C as a rigid system, for rotationabout the hinge? For analysis, break the beam into a short piece to the left of thehinge, and a separate longer piece to the right of the hinge. If the support cable D on should break,d) what is the angular acceleration of the beam and weights at the moment the cable breaks?e) what is the magnitude of the linear acceleration experienced by each of the weights, A and C, at moment the cable breaks?
The quadriceps tendon attaches to the tibia at a 30° angle 4 cm from the joint center at the knee. When an 80 N weight is attached to the ankle 28 cm from the knee joint, how much force is required of the quadriceps to maintain the leg in a horizontal position? When the subject mass is 75 kg, what is the magnitude and direction of the reaction force exerted by the femur on the tibia? (Utilize “Foot and leg” in the included chart to obtain weight of the lower leg and location of COM. Neglect the action of other muscles.)