021/pluginfile.php/680076/mod_resource/content/1/EENG3230_2022.pdf 4- Question 3 Two blocks, A and B, of mass m and 3m respectively, are connected through a cable and a pulley (see figure 3.1). Block A is also attached to a spring, which is fixed to the ground and has a spring constant k = 50 N/m. Block B is on an inclined plane forming an angle of 30 degrees with the horizontal line. Block B is released from rest with no slack in the cable and with the spring not being stretched or compressed. Assign to m the value in kg of your body weight, then (a) calculate the distance covered by block B once it stops for the first time; assume that there is no friction. (b) assume a kinetic friction force F = 5 N acts on block B and calculate the distance covered by block B once it stops for the first time. State any assumptions and comment on your solutions. B 3m m H 30° or

021/pluginfile.php/680076/mod_resource/content/1/EENG3230_2022.pdf 4- Question 3 Two blocks, A and B, of mass m and 3m respectively, are connected through a cable and a pulley (see figure 3.1). Block A is also attached to a spring, which is fixed to the ground and has a spring constant k = 50 N/m. Block B is on an inclined plane forming an angle of 30 degrees with the horizontal line. Block B is released from rest with no slack in the cable and with the spring not being stretched or compressed. Assign to m the value in kg of your body weight, then (a) calculate the distance covered by block B once it stops for the first time; assume that there is no friction. (b) assume a kinetic friction force F = 5 N acts on block B and calculate the distance covered by block B once it stops for the first time. State any assumptions and comment on your solutions. B 3m m H 30° or

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A 30kg mass is tied to a uniform rod whose mass and length are 80-kg and 8-m, as shown below. The rod is attached to the floor via a hinge and makes an angle of 70° relative to the ground; a massless string is also attached to the rod at the ¼ point of the rod and makes an angle of 20° relative to the horizontal. What tension must be provided by the rope so that the system remains in stationary? If at some point the string breaks, what will be the angular acceleration of the system the instant that the string breaks?
Under some circumstances, when two parallel springswith constants k1 and k2 support a single mass, theeffective spring constant of the system is given byk 4k1k2/(k1 + k2). A mass weighing 20 pounds stretchesone spring 6 inches and another spring 2 inches. Thesprings are first attached to a common rigid supportand then to a metal plate. As the figure illustrates(see image), the mass is attached to the center of the plate in the distributiondouble spring. Determine the constant of theeffective spring for this system. find the equationof motion if the mass is initially released fromequilibrium position with downward speed of2 ft/sec.
A 68 kg mass is supported by the three springs as shown. The initial displacement is 15 cm downward from the static equilibrium position. No external forces act on the mass after it is released. The equivalent spring constant is 5600 N/m. What is the static deflection of the mass? [Don't copy from other site]
A worker places an aluminum ladder on a horizontal concrete slab against a vertical wooden wall at 30 degrees from the vertical. The ladder has length L=5m and m=30 kg. The ladder’s CM is at a third of the length up. Worker Bob has mass M=90 kg and intends to climb up the ladder. Simultaneously, worker Charlie has mass M=90 kg and operates a rope through a single pulley to hoist a pail of mass m=30 kg. The axle of the pulley is anchored to the ladder at A=0.3 m along the ladder from the top point. Charlie is pulling the rope down with enough force to hoist the pail at uniform velocity. The mass of the pulley and rope are negligible. The friction in the pulley axle is negligible. The ladder is equipped with rubber booties and a rubber top. The kinetic friction coefficients are: rubber on dry concrete 0.9, rubber on dry wood 0.9, aluminum on wet concrete 0.2, aluminum on wet wood 0.2. b) Repeated use has deteriorated the rubber coating of the ladder, exposing the aluminum under it. In…
A worker places an aluminum ladder on a horizontal concrete slab against a vertical wooden wall at 30 degrees from the vertical. The ladder has length L=5m and m=30 kg. The ladder’s CM is at a third of the length up. Worker Bob has mass M=90 kg and intends to climb up the ladder. Simultaneously, worker Charlie has mass M=90 kg and operates a rope through a single pulley to hoist a pail of mass m=30 kg. The axle of the pulley is anchored to the ladder at A=0.3 m along the ladder from the top point. Charlie is pulling the rope down with enough force to hoist the pail at uniform velocity. The mass of the pulley and rope are negligible. The friction in the pulley axle is negligible. The ladder is equipped with rubber booties and a rubber top. The kinetic friction coefficients are: rubber on dry concrete 0.9, rubber on dry wood 0.9, aluminum on wet concrete 0.2, aluminum on wet wood 0.2. c) Alarmed by the unsafety of the worn-out ladder in wet conditions, Bob decides to “stabilize” it by…
A worker places an aluminum ladder on a horizontal concrete slab against a vertical wooden wall at 30 degrees from the vertical. The ladder has length L=5m and m=30 kg. The ladder’s CM is at a third of the length up. Worker Bob has mass M=90 kg and intends to climb up the ladder. Simultaneously, worker Charlie has mass M=90 kg and operates a rope through a single pulley to hoist a pail of mass m=30 kg. The axle of the pulley is anchored to the ladder at A=0.3 m along the ladder from the top point. Charlie is pulling the rope down with enough force to hoist the pail at uniform velocity. The mass of the pulley and rope are negligible. The friction in the pulley axle is negligible. The ladder is equipped with rubber booties and a rubber top. The kinetic friction coefficients are: rubber on dry concrete 0.9, rubber on dry wood 0.9, aluminum on wet concrete 0.2, aluminum on wet wood 0.2. Still disappointed with the ladder performance, Bob takes four old rubber boots, cuts off the tops and…
A worker places an aluminum ladder on a horizontal concrete slab against a vertical wooden wall at 30 degrees from the vertical. The ladder has length L=5m and m=30 kg. The ladder’s CM is at a third of the length up. Worker Bob has mass M=90 kg and intends to climb up the ladder. Simultaneously, worker Charlie has mass M=90 kg and operates a rope through a single pulley to hoist a pail of mass m=30 kg. The axle of the pulley is anchored to the ladder at A=0.3 m along the ladder from the top point. Charlie is pulling the rope down with enough force to hoist the pail at uniform velocity. The mass of the pulley and rope are negligible. The friction in the pulley axle is negligible. The ladder is equipped with rubber booties and a rubber top. The kinetic friction coefficients are: rubber on dry concrete 0.9, rubber on dry wood 0.9, aluminum on wet concrete 0.2, aluminum on wet wood 0.2. a) Calculate the safety limit in terms of maximal height off the ground that Bob can reach climbing up…
Dynamics of rigid bodies Problem 2
Figure below shows a mass-spring model of the type used to design packaging systems and vehicle suspensions, for example. The springs exert a force that is proportional to their compression, and the proportionality constant is the spring constant k. The two side springs provide additional resistance if the weight W is too heavy for the center spring. When the weight W is gently placed, it moves through a distance x before coming to rest. From statics, the weight force must balance the spring forces at this new position. (if x=d) These relations can be used to generate the plot of x versus W. (a) The following values are given: k1=104 N/m; k2 = 1.5 *104 N/m; d =0.1 m. Create a function that computes the distance x, using the input parameter W; Then, test your function for the following two cases, using the values: W=500 N W=2000 N. (b) Create another script and use your function to plot x versus W for 0 < W < 3000 N for the values of k1, k2, and d given in part a.
Using the figure below for a mass-spring system and given that R2 = 2R1, derive the equation of motion for the system in terms of x. Assume that the pulleys are massless, and the answer should be a differential equation that must include x, f, and their (high-order)derivatives.
● Weight of forearm = 1.6kg ● Center of mass (COM) = 18cm from elbow ● Weight of load held: 15 kg ● Forearm length: 36cm a) What is the force of the forearm (in N)? b) In what direction is the force of the force of the forearm? Positive or negative c) Demonstrate how you found the force of the forearm d) What is the force of the load (in N)? e) In what direction is the force of the load? F) Demonstrate how you found the force of the load
The figure shows the Russel fracture traction device and a mechanical model of the leg. The leg is held in balance in the position indicated by the two weights attached to the two cables. The combined weight of the leg and the cast is W=210 N. The horizontal distance between points A and B where the cables are attached to the leg is L=100 cm and the vertical distance is d=6 cm. Point C is the center of gravity of the cast and leg at three quarters of the L measured from point A (3L/4= 75 cm). The angle that cable 2 makes with the horizontal is measured as β=33°. Accordingly, in order for the leg to remain in balance in the shown position; a) Find the tensile force T1 in cable 1. (Write your result in N) b) Find the tensile force T2 in cable 2. (Write your result in N) c) Find the angle α of cable 1 with the horizontal.