2. When a cylindrical body is subjected to uniaxial tensile force, which types of stresses areformed within the body? Show the locations of stresses on an appropriate sketch.3. (a) If you were designing a metallic tool to be used at very low temperatures (negativetemperatures), which material class would be the best option?(b) If you wanted to increase the strength of that tool for that very low temperature, whichstrengthening method would be the best option? Briefly explain your answer.

Answered: Image /qna-images/answer/b110c0ca-eeba-48b5-b2e8-3616278911f6.jpg

Answered: 2. When a cylindrical body is subjected…

2. When a cylindrical body is subjected to uniaxial tensile force, which types of stresses are formed within the body? Show the locations of stresses on an appropriate sketch.

Steel Design (Activate Learning with these NEW titles from Engineering!)

6th Edition

ISBN:9781337094740

Author:Segui, William T.

Publisher:Segui, William T.

Chapter1: Introduction

Section: Chapter Questions

Problem 1.5.2P: A tensile test was performed on a metal specimen having a circular cross section with a diameter of...

See similar textbooks

Similar questions

The data in Table 1.5.3 were obtained from a tensile test of a metal specimen with a rectangular cross section of 0.2011in.2 in area and a gage length (the length over which the elongation is measured) of 2.000 inches. The specimen was not loaded to failure. a. Generate a table of stress and strain values. b. Plot these values and draw a best-fit line to obtain a stress-strain curve. c. Determine the modulus of elasticity from the slope of the linear portion of the curve. d. Estimate the value of the proportional limit. e. Use the 0.2 offset method to determine the yield stress.
The results of a tensile test are shown in Table 1.5.2. The test was performed on a metal specimen with a circular cross section. The diameter was 3 8 inch and the gage length (The length over which the elongation is measured) was 2 inches. a. Use the data in Table 1.5.2 to produce a table of stress and strain values. b. Plot the stress-strain data and draw a best-fit curve. c. Compute the, modulus of elasticity from the initial slope of the curve. d. Estimate the yield stress.
Compare the engineering and true secant elastic moduli for the natural rubber in Example Problem 6.2 at an engineering strain of 6.0. Assume that the deformation is all elastic.
A tensile test was performed on a metal specimen having a circular cross section with a diameter 0. 510 inch. For each increment of load applied, the strain was directly determined by means of a strain gage attached to the specimen. The results are, shown in Table: 1.5.1. a. Prepare a table of stress and strain. b. Plot these data to obtain a stress-strain curve. Do not connect the data points; draw a best-fit straight line through them. c. Determine the modulus of elasticity as the slope of the best-fit line.
A tensile test was performed on a metal specimen having a circular cross section with a diameter of 1 2 inch. The gage length (the length over which the elongation is measured) is 2 inches. For a load 13.5 kips, the elongation was 4.6610 3 inches. If the load is assumed to be within the linear elastic rang: of the material, determine the modulus of elasticity.
A part’s maximum Von Mises stress and materials are given below. Determine for each of these conditions whether the part is safe or not. Material: Steel, Von Mises Stress: 31000 psi, Static Loading, Ultimate Strength = 80000 psi Material: Polystyrene, Von Mises Stress: 42000 psi, Static Loading, Ultimate Strength = 7500 psi Material: Aluminum, Von Mises Stress: 62000 psi, Repeated Loading, Ultimate Strength = 30000 psi Please clearly show all calculations and reasoning in your computation.
STRENGTH OF MATERIALS. Please show the complete solutions. NO LONG EXPLANATION NEEDED! Rate will be given. Answer ASAP! Please answer all. MULTIPLE CHOICE: CHOOSE THE CORRECT ANSWER 1. Using MOHR CIRCLE from the given stresses on two perpendicular planes what is the normal stress on plane a-a? a. 75 MPa b. 150 MPa c. 125 MPa d. 100 MPa
The information in the photo attached shows elastic properties of a human tibula bone. If you were to take a small cuboidal cross section of the tibula bone and apply the ultimate shear stress, what would be the resulting strain? (a) 1.0 % (b) 6.7 % (c) 10 % (d) 15 % (e) None of the above.
A steel bar 25cm long of rectangular cross section 25mm by 50mm is subjected to a uniform tensile stress of 200N/m^2 along it's length.find the changes in dimension.E=205000N/mm^2, poison ratio=0.3
A cylindrical rod AB has a length ? = 80 cm and a diameterof ? = 2 cm. The modulus of elasticity is ? = 200 GPa andyield strength is ?? = 300 MPa. The stress-strain diagram ofthe rod is shown in the left figure. A force ? = 100 kN isapplied to the bar and then fully removed (right figure).Determine the permanent set in the rod.
Defferentiate the following terms; 1.Resilience and proof resilience 2.proof resilience and modulus of resilience B)A solid beam ABC circular in section has varying sections.portion AB is 6m in length and diameter of 250mm while portion BC is 2m in length and section diameter of 100mm.The beam is subjected to a sudden tensile load.if the maximum stress induced is 400MN/m^2.Determine the strain energy stored in the beam.Take E=200GN/m^2
Calculate the plane stresses involved where two pieces of steel are welded together. Our sign convention defines forces causing the object to be in tension positive and forces causing the object to be in compression negative. As we can see from the picture our σx = −4.5MPa and σy = 10MPa. Steel has an average Young’s modulus of elasticity of E = 200 GPa and an average Poisson’s ratio of ν = .285 Because it is not defined we will assume that initially there is no shear stress, τxy = 0. Solve only for: Compression in the x-direction(deformation along the weld)=(-Blank 4)? x 10^-5