2.23 WP A gas contained within a piston-cylinder assembly under-goes three processes in scries:Process 1-2: Constant volume from p = 1 bar, V₁ = 4 m³ to state2, where p₂ = 2 bar.Process 2-3: Compression to V₁ = 2 m³, during which the pres-sure-volume relationship is pV = constant.Process 3-4: Constant pressure to state 4, where V₁ = 1 m³.Sketch the processes in series on p-V coordinates and evaluate thework for cach process, in kJ.

GivenProcess 1-2constant voulme processP1=1barV1=4m3P2=2 barProcess 2-3PV = constantV3=2m3Process…

2.23 WP A gas contained within a piston-cylinder asseml goes three processes in scries: Process 1-2: Constant volume from p₁ = 1 bar, V₁ = 4 2, where p₂ = 2 bar. Process 2-3: Compression to V, = 2 m³, during which sure-volume relationship is pV = constant. Process 3 4: Constant pressure to state 4, where V.

2.23 WP A gas contained within a piston-cylinder asseml goes three processes in scries: Process 1-2: Constant volume from p₁ = 1 bar, V₁ = 4 2, where p₂ = 2 bar. Process 2-3: Compression to V, = 2 m³, during which sure-volume relationship is pV = constant. Process 3 4: Constant pressure to state 4, where V.

Refrigeration and Air Conditioning Technology (MindTap Course List)

8th Edition

ISBN:9781305578296

Author:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson

Publisher:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson

Chapter2: Matter And Energy

Section: Chapter Questions

Problem 14RQ: Four pounds of a gas occupy 10 ft3. What would be itsdensity and specific gravity?

See similar textbooks

Similar questions

A town has a 1.4-million-gallon storage capacity water tower. If the density of water is 62.4 lb/ft3 and local acceleration of gravity is 32.1 ft/s2, what is the force, in lbf, the structural base must provide to support the water in the tower?
Question #1 a) The absolute pressure inside a tank is 0.13bar, and the surrounding atmospheric pressure is 98 kPa. A Bourdon gage is mounted in the tank wall to measure the pressure, in kPa? Is this a vacuum or gage reading? b) (967)kJ of heat is transferred from the system to the surroundings when a closed system of mass (28)kg undergoes a process. During the process, 200kJ work is done on the system. If the initial specific internal energy of the system is 300 kJ/kg, Describe the process and determine the final specific internal energy, in kJ/kg? Neglect changes in kinetic and potential energy.
Which of the following is intensive property heat: work, internal energy, specific heat, heat capacity, pressure
Given the lifting table shown below, The diameter of the plunger DP 20 cm. The ram diameter DR 60 cm , The efficiency is 100 %, The stroke of the plunger is 30 cm. The ram has to raise a load F2 = 20 kN. Find: a) The force F1 exerted on the plunger b) the number of strokes needed to raise the load given above by a distance of 10 cm . c) the volume of oil pumped if the load moves by 30 cm (using plunger force given in a ) d) What will be the new diameter of the ram piston if the new load force is 16 times the force exerted in the plunger the diameter of the plunger is kept to 20cm. (please check the picture carefully).
Volume of the rigid tank is always ..... its specific volume A)Equal to B)Greater than C)None of these D)Less than
In a hydraulic system, a piston with a cross-sectional area of 21 square centimeters pushes on an incompressible liquid with a force of 38 newtons. The far end of the hydraulic pipe connects to a second piston with a cross-sectional surface area of 100 square centimeters. What is the force on the second piston?
As shown in the figure below, air is contained in a vertical piston–cylinder assembly such that the piston is in static equilibrium. The atmosphere exerts a pressure of 14.7 lbf/in.2 on top of the 4-in.-diameter piston. The absolute pressure of the air inside the cylinder is 16 lbf/in.2. The local acceleration of gravity is g = 32.2 ft/s2. Determine (a) the mass of the piston, in lb, and (b) the gage pressure of the air in the cylinder, in psig.
Given the lifting table shown below , The diameter of the plunger DP 8 cm.The ram diameter DR 48 cm , The efficiency is 100 %, The stroke of the plunger is 18 cm. The ram has to raise a load F2 = 2 kN. Find : a) the force F1 exerted on the plunger b) the number of strokes needed to raise the load given above by a distance of 10 cm c) the volume of oil pumped if the load moves by 20 cm ( using plunger force in a ) d) What will be the new diameter of the ram piston if the new load force is 16 times the force exerted in the plunger the diameter of the plunger is kept to 8cm .
A-3.2. Suppose a large tank of water with a temperature of just over 0 Cwe put in a 100 g ice cube. When the ice melts, it absorbs 33 kJ of heat. What is theentropy change of a) (ice) system, b) environment (water tank)?
A manometer consists of a U-shaped tube containing a liquid. One side is connected to the apparatus and the other is open to the atmosphere. The pressure p inside the apparatus is given p = pex + ρgh, where pex is the external pressure, ρ is the mass density of the liquid in the tube, g = 9.806 m s−2 is the acceleration of free fall, and h is the difference in heights of the liquid in the two sides of the tube. (The quantity ρgh is the hydrostatic pressure exerted by a column of liquid.) (i) Suppose the liquid in a manometer is mercury, the external pressure is 760 Torr, and the open side is 10.0 cm higher than the side connected to the apparatus. What is the pressure in the apparatus? The mass density of mercury at 25 °C is 13.55 g cm−3. (ii) In an attempt to determine an accurate value of the gas constant, R, a student heated a container of volume 20.000 dm3 filled with 0.251 32 g of helium gas to 500 °C and measured the pressure as 206.402 cm in a manometer filled with water at 25…
THERMODYNAMICS UPVOTE WILL BE GIVEN. PLEASE WRITE THE COMPLETE SOLUTIONS. NO LONG EXPLANATION NEEDED. BOX THE FINAL ANSWER AND USE 3 DECIMAL PLACES. DRAW PV-TS Diagrams. A scuba tank contains 1.5 kg of air. The air in the tank is initially at 15°C. The tank is left near an engine exhaust line, and the tank's pressure doubles. Determine (a) the final temperature; (b) the change in internal energy; (c) the heat added. (d) ΔS. please see the image attached for the constants
solve. heat transfer