20 mm 75 mm 10 mm 37.5 mm 37.5 mm

Q: The bell-crank mechanism is in equilibrium for an applied load of F₁ = 13 kN applied at A. Assume a…

A:

Q: 6. If the bolt head and the supporting bracket are made of the same material having a failure shear…

A: As per given question  Shear stress =120 mpa Factor of safety=2.5 We have to find maximum allowable…

Q: The bell-crank mechanism is in equilibrium for an applied load of F₁ = 11 kN applied at A. Assume a…

A:

Q: The tension member is fastened together using two bolts, one on each side of the member as shown.…

A: Given data: Diameter of bolt, d = 0.3 in. Shear stress, τ = 12 ksi Normal stress, σ= 20 ksi The free…

Q: Determine the elongation of the bar in Problem when both the load P and the supports are removed.

A: Given data Length of the bar AB LAB = 5 ft To determine elongation of the bar when both the load P…

Q: The 10-mm-diameter steel bolt is surrounded by a bronze sleeve. The outer diameter of this sleeve is…

A: Given data: *The diameter of the steel bolt is ds=10 mm. *The outer diameter of the sleeve is db=20…

Q: If the allowable tensile stress for the bar is (o,) allow = 21 ksi, and the allowable shear stress…

A:

Q: The bell-crank mechanism is in equilibrium for an applied load of F₁ = 11 kN applied at A. Assume a…

A:

Q: F11-2. Determine the minimum diameter d to the nearest in. of the rod to safely support the load.…

A:

Q: Determine the allowable weight that the assembly can handle if the cable AB has a working stress of…

A:

Q: The bell-crank mechanism is in equilibrium for an applied load of F1 = 19 kN applied at A. Assume a…

A:

Q: The bell-crank mechanism is in equilibrium for an applied load of F1 = 17 kN applied at A. Assume a…

A:

Q: If the bolt head and the supporting bracket are made of the same material having a failure shear…

A: Determine the allowable shear stress.

Q: 2-A-The bar is pinned at A and supported by two aluminum rods, each having a diameter of 25 mm and a…

A:

Q: A structural member is fabricated with the cross section show below and is eccentrically loaded with…

A:

Q: The concrete post is reinforced using six steel reiforcing rods, each having a diameter of 20 mm.…

A: Given data: Diameter of each rod = d = 20 mm Applied axial load = P = 900 kN Modulus of elasticity…

Q: The bell-crank mechanism is in equilibrium for an applied load of F1 = 16 kN applied at A. Assume a…

A: Given: F1 = 16 kN  a = 330mm, b = 170mm, c = 75mm, and θ = 50° diameter =23 mm  thickness = 35 mm To…

Q: The bell-crank mechanism is in equilibrium for an applied load of F₁ = 18 kN applied at A. Assume a…

A:

Q: A C 45° B |30° D P

A:

Q: For the connection shown, determine the average shear stress in the 0.75-in.-diameter bolts if the…

A: Given: Let us consider the given data,  d=0.75P=56 kipsn=5 Where, d=Diameter P=Applied load n=Bolt…

Q: 1-55: In the structure shown, an 8 mm diameter pin is used at A, and 12-mm- diameter pins are used…

A: Given Data Pin diameter at, A= 8mm Pin diameter at, B= 12mm shear stress, τ=100 MPa Ultimate…

Q: The rigid pipe is supported by a pin at A and an A-36 guy wire BD. If the wire has a diameter of…

A: Free-body diagram of the rigid pipe is given as,     On using equilibrium of moment about A,…

Q: 8-10. The A-36-steel band is 2 in. wide and is secured around the smooth rigid cylinder. If the…

A: Given:Tension, F=400 lbthickness, t=18 inwidth=2 in

Q: B D The rods AB and CD are assumed to be pin connected at A and C. If the cable BD and CD are made…

A: Draw the free body diagram as follows.

Q: The bell-crank mechanism is in equilibrium for an applied load of F1 = 11 kN applied at A. Assume a…

A: GIVEN DATA- F1=11KN DIA. OF PIN d=29mm t=31mm WE HAVE TO FIND SHEAR STRESS IN PIN AND BEARING STRESS…

Q: A3-5. The soft-ride suspension system of the mountain bike is pinned at C and supported by the shock…

A:

Q: The tension member is fastened together using two bolts, one on each side of the member as shown.…

A: Please find the answer below

Q: For the connection shown, determine the average shear stress in the 0.75-in.-diameter bolts if the…

A: Given data: P=64 kips diameter of bolt (d)= 0.75 in.

Q: The 65 kg tag is supported by cables AB and BC, as shown in the image, which have diameters of 1.5…

A:

Q: Q1/ The yoke-and-rod connection is subjected to the load shown below. Determine to the nearest one…

A: Given data,Normal failure stress δN=400 MPaShear failure stress δS = 240 MPaFs)N = 2 ; Fs)S =…

Q: A-36 guy wire AB. If the wire has a diameter of 0.2 in 337. The rigid pipe is supported by a pin at…

A:

Q: The bell-crank mechanism is in equilibrium for an applied load of F₁ = 11 KN applied at A. Assume…

A: Solution - given data -F1 =11KNθ =40°a =300 mmb =120 mmc =75 mm

Q: Q1/ A bracket is supported by means of 4 rivets of the same size. Design the 1.11. Alalka diameter…

A:

Q: The bell-crank mechanism is in equilibrium for an applied load of F₁ = 12 kN applied at A. Assume a…

A:

Q: The rigid beam is supported by a pin at C and an A-36 steel guy wire AB. If the wire has a diameter…

A: Draw the schematic diagram for the triangle BB’C system. Determine the angle with the help of…

Q: The rigid pipe is supported by a pin at A and an A-36 steel guy wire BD. If the wire has a diameter…

A: Given data: The diameter of the wire, d =0.25 in. Load acting on point C, P = 600 lb. For A-36…

Q: Determine the maximum allowable load P that can be safely supported by the frame if t = 1.25 in. and…

A: Given data as per the question t=1.25 in b=3.5 in normal failure stress of σfail = 6 ksi Shear…

Q: The connection is made using a bolt and nut and two washers. If the allowable bearing stress of the…

A: Given data: The allowable bearing stress of the washers on the boards, (σb)allow = 2 ksi. The…

Q: The bell-crank mechanism is in equilibrium for an applied load of F₁ = 13 kN applied at A. Assume a…

A: Given: Let us consider the given data, F1=13 kN=13×103Na=300 mmb=190 mmc=90 mmθ=35°d=31 mmt=26 mm To…

Q: The bell-crank mechanism is in equilibrium for an applied load of F1 = 11 kN applied at A. Assume a…

A: F1= 11 kN= 11000 N a= 250 mm b= 100 mm c= 90 mm θ= 40∘ Diameter, d= 29 mm Thickness, t= 31 mm   To…

Q: What is the maximum possible value of theclamping force C in the jaws of the pliers shown inthe…

A: Given; The diameter of the pin = 5 mm The ultimate shear stress = 340 MPa The factor of safety = 3

Q: Determine the minimum diameter d to the nearest 18 in. of the rod to safely support the load. The…

A: Gven: σ=22 ksiτ=10 ksi

Q: The bell-crank mechanism is in equilibrium for an applied load of F1 = 12 kN applied at A. Assume a…

A:

Q: A 100-mm-long rod has a diameter of 15 mm. If an axial tensile load of 10 kN is applied to it,…

A:

Q: F7-23. If the bolt head and the supporting bracket are made of the same material having a failure…

A: Given: Failure shear stress material of the screw is τfail=120MPa and factor of safety is N=2.5 The…

Q: the right-angle bar is supported by a pin at B and a roller at C. what is the maximum safe value of…

A: Shear stress is a force that tends to distort a material by causing it to slide along a plane or…

Q: Q1 (DÖÇ-1) In the given structure, the link BD has rectangular cross section of 18 mm × 8 mm, the…

A: Given: Rectangular cross-section = 18×8Diameter of pin at C (DC)=6mmDiameter of pin at B and D…

Q: Six nails are used to hold the hanger at A against the column. Determine the minimum required…

A: given Six nails are used to hold the hanger at A against the column.diameter of each nail to the…

Q: The right-angle bar is supported by a pin at B and a roller at C. what is the maximum safe value of…

A:

Q: The bell-crank mechanism is in equilibrium for an applied load of F₁ = 17 kN applied at A. Assume a…

A: