If the allowable tensile stress for the bar is (o,) allow = 21 ksi, and the allowable shear stress for the pin is Tallow = 12 ksi, determine the diameter of the pin so that the load P will be a maximum. What is this load? Assume the hole in the bar has the same diameter d as the pin. Take i = in. and w = 2 in.

If the allowable tensile stress for the bar is (o,) allow = 21 ksi, and the allowable shear stress for the pin is Tallow = 12 ksi, determine the diameter of the pin so that the load P will be a maximum. What is this load? Assume the hole in the bar has the same diameter d as the pin. Take i = in. and w = 2 in.

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter11: Columns

Section: Chapter Questions

Problem 11.4.14P

See similar textbooks

Similar questions

Determine the allowable axial load Pallowfor a steel pipe column that is fixed at the base and free at the top (see figure) for each of the following lengths: L = 2,6 m, 2.8 m, 3.0 m, and 3.2 m. The column has an outside diameter d = 140 mm and wall thickness t = 7 mm, (Assumed = 200 GPa and ( y= 250 MPa.)
A steel bar has a square cross section of width b = 2.0 in. (sec figure). The bar has pinned supports at the ends and is 3.0 ft long. The axial forces acting at the end of the bar have a resultant P = 20 kips located at distance e = 0,75 in, from the center of the cross section. Also, the modulus of elasticity of the steel is 29,000 ksi. Determine the maximum compressive stress max, in the bar. If the allowable stress in the steel is 18,000 psi, what is the maximum permissible length Lmaxof the bar?
Determine the maximum permissible length Lmaxfor a steel pipe column that is fixed at the base and free at the top and must support an axial load P = 500 kN (see figure). The column has an outside diameter d = 200 mm, wall thickness; = 10 mm, E = 200 GPa, and y = 250 MPa.
A steel column (E = 30 x 103 ksi) with pinned ends is constructed of a W10 x 60 wide-flange shape (sec figure). The column is 24 ft long. The resultant of the axial loads acting on the column is a force P acting with an eccentricity n = 2.0 in. If P = 120 kips, determine the maximum compressive stress ff^ in the column. Determine the allowable load Pallowif the yield stress is ( y =42 ksi and the factor of safety with respect to yielding of the material is n = 2.5.
A steel column ( E = 30 X 103 ksi) that is fixed at the base and free at the top is constructed of a W8 x 35 wide-flange member (sec figure). The column is 9.0 ft long. The force P acting at the top of the column has an eccentricity e = 1.25 in. If P = 40 kips, what is the maximum compressive stress in the column? If the yield stress is 36 ksi and the required factor of safety with respect to yielding is 2.1, what is the allowable load Pallow?
If the allowable tensile stress for the bar is 1st2allow = 21 ksi, and the allowable shear stress for the pin is tallow = 12 ksi, determine the diameter of the pin so that the load P will be a maximum. What is this load? Assumethe hole in the bar has the same diameter d as the pin. Take t = 1 4 in. and w = 2 in.
The right-angle bar is supported by a pin at B and a roller at C. what is the maximum safe value of the load P that can be applied if the shear stress in the pin is limited to 20,000 psi? the 3/4 -diameter pin is in double shear.
Determine the load that can be applied at the end of the rigid bar if the stressin either spring shown in the figure shall not exceed 200MPa. Present detailed drawings/FBD’s illustrating your solution.
NEED ANSWER ASAP !!! The axial load 274 kN applied to the lap joint is distributed equally among the three 26.5-mm-diameter rivets. What is the bearing stress (in MPa) between a plate and a rivet if w = 135.4 mm and t = 29.5 mm?
The bar is connected to the support using a pin having a diameter of d = 1 in. If the allowable tensile stress for the bar is 1st2allow = 20 ksi, and the allowable bearing stress between the pin and the bar is 1sb2allow = 30 ksi,determine the dimensions w and t so that the gross area of the cross-section is wt = 2 in2 and the load P is a maximum. What is this maximum load? Assume the hole in the bar has the same diameter as the pin.
2. A hollow steel tube with an inside diameter of 100 mm must carry a tensile load of 400 kN. Determinethe outside diameter of the tube if the stress is limited to 120 MN/m2.
A mechanism used in printing machinery consists of a helical spring which is having a wire diameter of 5mm and an outside diameter of 54mm. The spring has 16 active coils. If the permissible shear stress of the spring material is 335 N/mm2 and the Modulus of rigidity is 82 kN/mm2. a) Calculate the axial load in N and the deflection of the spring in mm, neglecting the effect of curvature. b) Calculate the value of axial load in N considering the effect of curvature.