21. A 5V3350 drive belt is connected to a normal torque squirrel-cage electric motor operating at 1,750 rpm. Sheaves for both driver pulley are 12.5 in in diameter. Find the center distance given that the length of this type of belt is 335 inches. C. 234.542 inches D. 120.543 inches A. 147.875 inches B. 154.543 inches 3

21. A 5V3350 drive belt is connected to a normal torque squirrel-cage electric motor operating at 1,750 rpm. Sheaves for both driver pulley are 12.5 in in diameter. Find the center distance given that the length of this type of belt is 335 inches. C. 234.542 inches D. 120.543 inches A. 147.875 inches B. 154.543 inches 3

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

nsmitted by a belt running over a pulley of 600 my, n between the belt and the pulley is 0.25, angl of lap
(10) The lead screw of a lathe has a 2.0-in Acme thread, 2½TPI. To drive the tool carriage, this screw must exert an axial force of 600lb. The thrust is carried on the collar 4½-in outside diameter & 2¼- in in inside diameter. The lead screw revolves 30rpm. Determine: (a) the efficiency of the screw & the collar, assuming ft = 0.15 & fc = 0.10 ; (b) the power to drive the screw.
An industrial fan running at 600 rpm is driven by a 25 kW, 960 rpm, induction motor. The pulley mounted on the motor shaft is 270 mm. Center to center distance is 1.45 m and use f = 0.35. Determine the length of leather belt
A shaft turning 200 RPM is to drive another shaft at 250 RPM connected in open belt. Find the diameters of the two pulleys, using integral number of inches for each diameter, to give as nearly as possible a belt speed of 3500 FPM.
A pump is driven by an electric motor through a open type flat belt drive.Motor pulley diameter (DS) = 300 mm, Pump pulley diameter (DL) = 600 mm. The Center distance between the pulleys=1000 mm. Find the length of the belt in inches
Which of the following threads is ideal for power transmission? a. Buttress Thread b. Square Thread c. Metric Thread d. ACME Thread Cold working of steel is defined as working a. Below its recrystallization temperature b. At two thirds of the melting temperature of the metal c. At its recrystallization temperature d. Above its recrystallization temperature
41. Buttress threads are used for withstanding high forces in one direction only.Select one:TrueFalse
The following are five different types of machoines 1. Pulley block 2. Lever 3. Worm and wheel 4. Incline plane 5. Screw Jack Discuss the operation of these machines. The discussion should include velocity ratio, mechanical advantage and efficiency
A metric thread of pitch 2 mm and thread angle 60° is inspected for its pitch diameter using 3 wire method. The diameter of the best size wire in mm is, (a) 0.866 (b) 1.000 (c) 1.154 (d) 2.000
The economical speed for leather belting is around 4,500 fpm (ft/min). A pulley of what diameter in inches should be used on a motor running at 1760 rpm to give the required belt speed, if there is no slipping between the belt and pulley?
A belt-driven blower assembly is equipped with a motorthat turns a 5-in. drive pulley at a speed of 3450 rpm.The blower is turning at a speed of 1725 rpm. Determinethe size of the driven pulley.
In a belt drive design, the angle of wrap correction factor C θ is a function of the angle of wrap of the belt on the small sheave. If in a design, the angle of wrap of the belt on the small sheave is 1500 , then C θ = ________ 0 .