(2a.) A metal has a flexural stress of 564 Pa. The W is measured to be 1 meter, while the load was 10 N. The thickness of the metal is twice its L. Using the formula on the three-point test of materials, compute for the thickness of the metal in centimeters. 0.0532 5.3191 28.2928 0.2829 (2b.) What is the L in centimeters of the same metal in (2a)? * 2.6596 0.0266 7.0734 0.0707

(2a.) A metal has a flexural stress of 564 Pa. The W is measured to be 1 meter, while the load was 10 N. The thickness of the metal is twice its L. Using the formula on the three-point test of materials, compute for the thickness of the metal in centimeters. 0.0532 5.3191 28.2928 0.2829 (2b.) What is the L in centimeters of the same metal in (2a)? * 2.6596 0.0266 7.0734 0.0707

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A metal block of cross-section area A and length L is subject to a tensile stress of S. The block elongates by a length of 0.002L. Another block made from the same metal is subject to the same tensile stress. If this block has a cross-section area of 2A and a length of 2L, determine the elongation of the block.
A seamless cylinder of storage capacity of 0.03m3 is subjected to an internal pressure of 21 MPa. The allowable stress in the material of cylinder is 350N/mm².Determine the length of the cylinder if it is twice the diameter of the cylinder.8mm A seamless cylinder of storage capacity of 0.03mᵌis subjected to an internal pressure of 21MPa. The ultimate strength of material of cylinder is 350N/mm².Determine the length of the cylinder if it is twice the diameter of the cylinder.540mm
When a thin cylinder is subjected to an internal pressure p, the tangential stress should be the criterion for determining the cylinder wall thickness. Explain.
Sketch the relationship between the stress and the number of cyclic loading applied on an element
Besides normal tensile stress, list three other types of material stresses? Are these typically all the same for a given material?
A metal has a flexural stress of 564 Pa. The W is measured to be 1 meter, while the load was 10 N. The thickness of the metal is twice its L. Using the formula on the three-point test of materials, compute for the thickness of the metal in centimeters.
A hollow metal tube with an inside diameter of 145 centimeters must carry a tensile load of 670 kilo newton. Determine the outside diameter of the tube, in meters, if the stress is limited to147 Mpa.
What is the difference between direct and shear stress?
Draw the tensile curves of the following materials, taking into account the appropriate elongation at break, modulus of elasticity and tensile stress, on the side stress-strain graph. a)Low carbon steel (Ecelik=200Gpa),(Syield=300MPa),(Stensile=400MPa) b)High carbon steel (Esteel=200GPa),(Stensile=700MPa) c)Aluminum (Ealuminum=70GPa), (Syield=200MPa),(Stensile=300MPa) d)Cast iron (Ecast iron=120GPa),(Stensile=200MPa)
In a tensile test for an aluminum alloy, the sample is 2 inches long and 0.5 inches in diameter. The proportional portion of the tension stress-strain diagram for an aluminum alloy is shown below. Now that the axial stress of the sample under a tensile load of 9 kips is below material's proportional limit, please calculate the elongation of the sample under the tensile load of 9 kips: ____ inch. Pay attention to units and calculate your answer to 4 decimal place.
STRENGTH OF MATERIALS. Please show the complete solutions. NO LONG EXPLANATION NEEDED! Rate will be given. Answer ASAP! Please answer all. MULTIPLE CHOICE: CHOOSE THE CORRECT ANSWER 1. Using MOHR CIRCLE from the given stresses on two perpendicular planes what is the normal stress on plane a-a? a. 75 MPa b. 150 MPa c. 125 MPa d. 100 MPa 2. Using MOHR CIRCLE, what is the resulting "HORIZONTAL" SHEARING STRESS at the given angle plane point? a. 44.03 MPa b. 64.32 MPa c. 185.68 MPa d. 75.00 MPa 3. Using MOHR CIRCLE, what is the resulting "VERTICAL" NORMAL STRESS at the given angle plane point? a. 44.03 MPa b. 75.00 MPa c. 64.32 MPa d. 185.68 MPa
The following data are obtained from a tensile test of a copper specimen. - The load at the yield point is 150 kN. - Length of the specimen is 24 mm. - The yield strength is 78 kN/mm2. - The percentage of elongation is 42 %. Determine the following iii) Stress under an elastic load of 14 kN, iv) Young's Modulus if the elongation is 1.7 mm at 14 kN and (v) Final diameter if the percentage of reduction in area is 26 %. I wont answer for this three questions only: 1)Final Area of the Specimen at Fracture (in mm) 2)Final Diameter of the Specimen after Fracture (in mm) 3)Initial Cross-sectional Area (in mm2)