3-20 mm diameter bolts fasten two plates being 25 mm thick and 130 mm wide. If the applied tensile load is 50 kN is distributed uniformly among the bolts, Compute for the tensile stress (MPa) in the plate at the critical section. Select the correct response: 28.57 18.18 15.38 19.23

3-20 mm diameter bolts fasten two plates being 25 mm thick and 130 mm wide. If the applied tensile load is 50 kN is distributed uniformly among the bolts, Compute for the tensile stress (MPa) in the plate at the critical section. Select the correct response: 28.57 18.18 15.38 19.23

Steel Design (Activate Learning with these NEW titles from Engineering!)

6th Edition

ISBN:9781337094740

Author:Segui, William T.

Publisher:Segui, William T.

Chapter7: Simple Connections

Section: Chapter Questions

Problem 7.11.10P

See similar textbooks

Related questions

Q: (c) a project engineer assisting one project manager in all of his or her capacities in the trailer ...

A: Project manager is very responsible person on the construction site. He plans, organise and divides ...

Q: The rigid bar ABC shown is hinged at A and supported by a steel rod at B. 25KN What is the tensile f...

Q: How do the Physical Properties of Mineral help in the field of Civil Engineering? Provide a thorough...

A: A mineral is an inorganic compound or element with an organized internal structure and distinct chem...

Q: 2. A 50-m tape weighs 2 kg. Every time a measurement is performed, the tape is supported at its end ...

A: Given Information: Weight of tape Pull applied Distance between supports To find: Correction due ...

Q: A bronze pipe (1) is to be connected to an aluminum alloy pipe (2) at flange B. When put in place, h...

Q: A CLAY SAMPLE HAS UNIT WEIGH OF 20.06kN/m3 WITH MOISTURE CONTENT OF 8.2%. THE SATURATED UNIT WEIGHT ...

A: To Determine Porosity of the soil.

Q: A solid circular bronze [G = 6,500 ksi] shaft, 6.4 ft long and 1.600 in. in diameter, carries a torq...

Q: 5. The solid shaft that is fixed connected at both ends has a diameter of 20 mm and a total length o...

A: The internal torsional moment can of a given Shaft can be shown with the help of torque diagram. Sig...

Q: solid 1.8 in. diameter shaft is used to synchronize multiple mechanisms in a manufacturing plant. Th...

A: Given data Diameter of shaft = 1.8in Torque developed in shaft= 3500lb-in= 291.67lb-ft Speed(N)= 5...

Q: Where does the maximum deflection occur for the beam shown? 80 kN B 12 m 21 E= constant = 200 GPa 12...

Q: A solid constant-diameter circular shaft is subjected to the torques of TA = 490 Ib-ft, Tg = 1070 Ib...

A: (a) Plot a torque diagram showing the internal torque in segments (1), (2), and (3) of the shaft. (...

Q: The truss shown consists of wooden members. Knowing that each member has a 50 x 50 mm. square cross-...

Q: Problem 4: Water flows inside a system made of two pipe sections with diameter D =1.5 fi and D, =0.5...

A: Given data - D1 = 1.5 ft , D2 = 0.5 ft. The manometer reading are h1= 0.75 ft and h2 = 0.25 ft. Volu...

Q: A bronze pipe (1) is to be connected to an aluminum alloy pipe (2) at flange B. When put in place, h...

Q: blity elow a dam is 4m/day. Thế water on the upstream de is 20m higher than on the downstream side. ...

A: Head at heel(h)=20m

Q: A rectangular channel 6 m wide by 1 m deep is laid on a slope of 0.001 has a roughness coefficient o...

Q: The rigid bar ABC shown is hinged at A and supported by a steel rod at B. 2m 25KN The thickness of t...

Q: A closed cylindrical tank with 0.30 m radius and 1.0 m height is fully-filled with water. The tank i...

A: Given data, Radius = 0.3 m Height = 1 m Initial pressure = 15 kPa To find out the pressure at cir...

Q: right end. Calculate the angle that the reaction at A make with the horizontal counterclockwise). Th...

A: To find angle that reaction at A makes with horizontal

Q: The influence line for the vertical reaction at C for the beam shown is B 7 m- 7 m 4 m-

Q: 7. From the following cross-section notes for a road grading work. -3.2 +1.2 +1.2 +2.8 X1 3.5 X2 The...

Q: SITUATION: A 3-layer soil has the following properties from top to bottom: Obtain the equivalent ver...

Q: 5. Compound Curve given elements: 1 = 20° D, = 4° Station of PC of compound curve = 8+ 120 2 = 25° D...

Q: 7. The following table shows traffic flow data collected at the main road in an urban area, in two s...

A: a) Calculate the peak hour factor by using formula as given as, PHF=VH4×V15 max Where, VH=Hourly vol...

Q: Determine the reactions at the support. 3 kN -2 m 2 kN. 1.5 m 2 kN 1.5 m A B Ax=4kN, Ay=4.5kN, By=4....

Q: The solid shaft that is fixed connected at both ends has a diameter of 20 mm and a total length of 2...

Q: 4. A closed traverse has the following data: Line Departure 37.39 Latitude DPD 2A АВ 1455.23 ВС 19.1...

Q: ely of a curve with a central angle of 30 degrees. If the distance c

A: solution of above question is below

Q: A load Pis supported by a structure consisting of rigid bar ABC, two identical solid bronze (E - 150...

A: Given data: As=1.228 in2Es=30000 ksiAb=0.637 in2Eb=15000 ksi

Q: Calculate the factored load capacity of a double channel section member of A36 steel according to AI...

Q: The rigid bar ABC shown is hinged at A and supported by a steel rod at B. 2 m 1m 25KN The thickness ...

Q: For the beam shown, the magnitude of the distributed load is wo - 10.2 kN/m and the beam length is L...

A: Given data:

Q: Classify the following fine grained soil as per IS soil classification system. Liquid limit = 90%, P...

Q: An A36 tension member shown in the figure is connected with three 19 mm diameter bolts. Dia. Of bolt...

Q: View Policies Current Attempt in Progress For the beam shown, the magnitude of the distributed load ...

Q: The sanding-drum mandrel shown in the figure is made for use with a hand drill. The mandrel is made ...

A: Given data:Inital diameter, Di=1.60 mFinal diameter, Df=1.73 m

Q: A shaft subjected to torsion experiences a pure shear stress on the surface. The maximum principal s...

Q: Problem 5. A pin and two rollers support bars ABC and CD. A hinge at C connects the bars. The distri...

Q: Current Attempt in Progress A pin-connected structure is supported and loaded as shown. Member ABCD ...

A: Given data -

Q: Determine the reaction/s at supports A and D if P1 = 28 lb, P2 = 98 Ib and x = 13 ft. What is the va...

Q: 6 kN 3 kN/m B |C D 1.5 m - 1.5 m 0.5 m 0.5 m!

Q: The 55-kg crate shown in the figure rests on a horizontal surface for which the coefficient of kinet...

Q: The long bolt passes through the 30-mm-thick plate. If the force in the bolt shank is 8 kN, determin...

A: We need to calculate area of each case.

Q: A solid 1.750-in.-diameter steel shaft is subjected to torques TB = 285 lb-ft and TD= 115 lb-ft, act...

A: We will find maximum torque in the shaft using shear stress.

Q: For the simply supported beam shown below, determine the internal resultant loadings at a point 0.5 ...

A: Determine the internal resultant loadings at a point 0.5 meters to the right of point C.

Q: A solid circular bronze [G- 6,500 ksi] shaft, 5.4 ft long and 1.125 in. in diameter, carries a torqu...

Q: A solid constant-diameter circular shaft is subjected to the torques of TA = 400 lb-ft, Tg = 110O Ib...

Q: 6. A symmetrical vertical summit curve has tangents of +4% and -2%. The allowable rate of change of ...

Q: SITUATION: A footing, 2m x 3m in plan and 0.50m thick, is designed to support a 0.60m square column....

A: Given data: Footing dimensions = 2 m x 3 m Square column dimensions = 0.6 m x 0.6 m Load on the colu...

Q: Current Attempt in Progress A polymer cylinder (2) is clamped between rigid heads by two steel bolts...

Concept explainers

Mechanics of Solids

It is the study of the behavior of solid materials, their characteristics under various circumstances such as variation in external forces, temperature, and other internal factors. It is one of most important study in the field of engineering science, especially chemistry and mechanical engineering. In rigid body, the idealization of the solid body in which deformation is neglected. Deformation is known as the force acting on the solid state system which exerts change in its shape of the body but it continues to be at rest or in a uniform motion but it cannot accelerate. But those solid systems do have elasticity, compressibility and can be bent. This field is very vast since there are wide range of materials around us.

Question

CT JO 7 IC
3-20 mm diameter bolts fasten two plates being 25 mm thick and 130 mm wide. If the applied tensile load is 50 kN is distributed uniformly among the bolts,
Compute for the tensile stress (MPa) in the plate at the critical section.
Select the correct response:
28.57
18.18
15.38
19.23

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

The cast iron block with cross-sectional dimensions of 62.5 mm by 62.55 mm consists of two pieces. The pieces are prevented from sliding along the 55 deg inclined joint by the steel key, which is 62.5 mm long. The working stresses are 275 MPa for cast iron bearing and 345 MPa for the key in shear. If the block is loaded with P=268 kN, calculate the required dimension "b" of the key. Write your final answer in 2 decimal places with the unit of mm.
If the allowable bearing stress in the bolt is 18.855 ksi. what is the minimumrequired diameter of the bolt at B? b= .75” h= 7.874” Distances are in feet.
an angle bar 100x100x11 mm tension member is connected with 20-mm-dia bolts as shown in the fig. both legs of the angles are connected. use fy=248 MPa and Fu=400 MPa. 1. determine the nominal strength for tensile yielding in the gross section. a. 515.59 kN b. 429.67 kN c. 545.60 kN d. 390.10 kN 2. determine the effective net area of member a. 1573 mm^2 b. 1632 mm^2 c. 1605 mm^2 d. 1815 mm^2 3. determine the nominal strength for tensile rupture in the net area. a. 642 kN b. 730 kN c. 554 kN d. 650 kN
A square hollow steel strut if thickness 10mm is pin connected to two connector plates of thickness, 12mm. The connector plates are welded to the base plate of thickness, 12mm. The base plate is fastened to te concrete base by 4-16mm diameter anchor bolts. The diameter of the pin is 16mm. Which of the following most nearly gives the shearing stress in the anchor bolts? Choices 150.00 MPa 59.68 MPa 51.69 MPa 119.37 MPa
A wide flange A60 steel column has a length of 5.8meters and pinned ends. If Sx=857x103 mm3, Sy=135x103 mm3, d=358mm, bf=171mm, A=7243mm2, Fy=414MPa, calculate the critical buckling stress, Fcr in MPa of the column. Express your answer in one decimal place.
8. determine the capacity of the details shown below.A992: Fy=50ksi, Fu=65ksiA36: Fy=36ksi, Fu=58ksieffective bolt hole diameter = bolt hole + 1/16"beam properties: tw=0.38 in., bf=7.07 in., tf=0.63 in.Fexx=70ksih) what is the flexural rupture capacity of the shear plate of the shear connection in kips? (2 decimal places)
Determine the capacity of the details shown below.A992: Fy=50ksi, Fu=65ksiA36: Fy=36ksi, Fu=58ksieffective bolt hole diameter = bolt hole + 1/16"beam properties: tw=0.38 in., bf=7.07 in., tf=0.63 in.Fexx=70ksi e) what is the shear rupture capacity of the shear plate of the shear connection in kips? (2 decimal places)
The bracket shown below consist of two plates riveted to a column by 4-20 mm Ø rivets which is subjected to an eccentric load of 150 kN. 1. Which of the following gives the shearing stress due to axial load only a. 29.84 MPa b. 42.20 MPa c. 49.32 MPa d. 66.72 MPa 2. Which of the following gives the shearing stress due to axial load only? a. 29.84 MPa b. 42.20 MPa c. 49.32 MPa d. 66.72 MPa 3. Which of the following gives the value of the maximum shearing stress in the rivets? a. 29.84 MPa b. 42.20 MPa c. 49.32 MPa d. 66.72 MPa
The given plate below with width of 200 mm andthickness of 16 mm is to be connected to two plates ofthe same width with half the thickness by 20 mmdiameter rivets as shown. The rivet hole is 2 mm greaterthan the rivet diameter. Allowable tensile stress on netarea is 0.6Fy. Allowable bearing stress is 1.35Fy. plate: fy = 241 mpa fu = 4141 mpa rivet: fv = 152 mpa a. Determine maximum load P without exceeding allowable tensile stress on plate b. Determine maximum load P without exceeding allowable shear stress on rivets c. Determine maximum load P without exceeding allowable bearing stress between plates and rivets
Question 1. Specify the forces applied to the beams of the beam structure and the load patterns of the horizontal bar BDF. Question 2. Calculate the cutting force developed by the cutters shown in the picture, as well as the force applied to the hinge pin cutting force: (10kp = 100N)
W 10x45 is connected to two plates with two lines of ¾” bolts as shown below. Determine the tensile strength of the system if Fy = 50 ksi and Fu = 65 ksi.
A flange bolt coupling has ten steel 25.4 mm diameter bolts evenly tighten around a 415 mm bolt circle. Determine the torque capacity of the connection if the allowable shearing stress in the bolt is 50 MN/m2 . A. 59.95 kN - m B. 52.6 kN - m C. 46.15 kN - m D. 43.8 kN – m