3-4. A shop works a 400-minute day. The manager of the shop wants an output of 200 units per day for the assembly line that has the elemental tasks shown in the table. Do the following: (a) Construct the precedence diagram. (b) Assign tasks according to the most following tasks rule. Determine efficiency. (Ans. 85%) (c) Assign tasks according to the greatest positional weight rule. Determine efficiency. (Ans. 85%) (d) Compute the balance delay for each rule. Which one yields the better set of assignments in this instance? (note. Balance Delay=(total idle time)/(total operation time)) (answer: 15%)

3-4. A shop works a 400-minute day. The manager of the shop wants an output of 200 units per day for the assembly line that has the elemental tasks shown in the table. Do the following: (a) Construct the precedence diagram. (b) Assign tasks according to the most following tasks rule. Determine efficiency. (Ans. 85%) (c) Assign tasks according to the greatest positional weight rule. Determine efficiency. (Ans. 85%) (d) Compute the balance delay for each rule. Which one yields the better set of assignments in this instance? (note. Balance Delay=(total idle time)/(total operation time)) (answer: 15%)

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

3-38 with the following modification change the block weight to 50 lb
Find the V-X and M-X diagrams. For the value of P use 182 kips. show all steps
5. draw a figure also, and explain each step by step solution.
5 A flight conveyor of dimensions 3 and 2 ft are moving at a speed of 87 fpm. The conveyor handles crushed rocks with a bulk density of 73 pounds per cubic feet. Determine the throughput of the process in TPH. Do not round off until the final answer which you will express in 2 decimal places.
solve by showing and explaining each step
solve show all steps/solution
If the wire diameter of a compressive helical spring is increased by 2%, the change in spring stiffness (in%) is _______ (correct to two decimal places.)
Solve the problem 6. Please
solve show all steps/solutions
1.ᴛʜᴇ ᴅʀʏ-ʙᴜʟʙ ᴛᴇᴍᴘᴇʀᴀᴛᴜʀᴇ ᴏꜰ ʜᴜᴍɪᴅ ᴀɪʀ ɪꜱ 35 ᴅᴇɢʀᴇᴇ ᴄ . ᴡʜᴀᴛ ɪꜱ ᴛʜᴇ ᴡᴇᴛ ʙᴜʟʙ ᴅᴇᴘʀᴇꜱꜱɪᴏɴ ɪɴ ᴅᴇɢʀᴇᴇ ꜰ ɪꜰ ᴛʜᴇ ᴡᴇᴛ -ʙᴜʟʙ ᴛᴇᴍᴘᴇʀᴀᴛᴜʀᴇ ɪꜱ 18 ᴅᴇɢ ᴄ Optionsᴀ) 17.6 ʙ) 18 ᴄ ) 30.6 ᴅ) ɴᴏᴛ ʟɪꜱᴛᴇᴅ 2. ᴅᴇᴛᴇʀᴍɪɴᴇ ᴛʜᴇ ᴅᴇᴡ-ᴘᴏɪɴᴛ ᴅᴇᴘʀᴇꜱꜱɪᴏɴ ᴏꜰ ᴛʜᴇ ʀᴏᴏᴍ ᴀɪʀ ᴡʜᴇɴ ᴛʜᴇ ᴅʀʏ-ʙᴜʟʙ ᴀɴᴅ ᴅᴇᴡ ᴘᴏɪɴᴛ ᴛᴇᴍᴘᴇʀᴀᴛᴜʀᴇ ɪꜱ 69.8 ᴅᴇɢ ꜰ ᴀɴᴅ 15 ᴅᴇɢ ᴄ , ʀᴇꜱᴘᴇᴄᴛɪᴠᴇʟʏ.Optionsᴀ ) 6 ᴅᴇɢ ᴄ, ʙ) 5.8 ᴅᴇɢ ᴄ, ᴄ ) 8 ᴅᴇɢ ᴅᴇɢ ᴄ, ᴅ) 7 ᴅᴇɢ ᴄPlease show solution and diagram if applicable thanks!
Solve and explain each step.
GIVEN: W= 595 N GIVEN: ANGLE A= 44 DEGREE GIVEN: ANGLE B= 14 DEGREE ANSWER: SOLVE (A) IN UNIT CM SOLVE (B) IN UNIT N-CM SOLVE (C) IN N-CM PLS SHOW COMPLETE SOLUTION AND WRITE LEGIBLY AND SHOW THE FREE BODY THE DIAGRAM PLS TAKE NOTE OF THE UNITS WHICH ARE IN CM NOT IN MM AND ALSO LOOK AT WHAT SHOULD BE THE UNITS IN SOLVING (A) IN UNIT CM IN (B) IN UNIT N-CM AND IN (C) IN N-CM.