3-56. A 2-in. Younded orifice exists in the horizontal bottom of a large tank. The water in the tank is 12 ft deep. Find the discharge through the orifice and the velocity in the jet 6 ft below the orifice. Cc = 1.0

3-56. A 2-in. Younded orifice exists in the horizontal bottom of a large tank. The water in the tank is 12 ft deep. Find the discharge through the orifice and the velocity in the jet 6 ft below the orifice. Cc = 1.0

Name: 3-56. A 2-in. Younded orifice exists in the horizontal bottom of a la
Uploaded: 2024-03-20T06:56:55.000Z
Channel: Bartleby
Description: 3-56. A 2-in. Younded orifice exists in the horizontal bottom of a largetank. The water in the tank is 12 ft deep. Find the discharge through the orificeand the velocity in the jet 6 ft below the orifice.Cc = 1.0

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The diameter of a pipe gradually reduces from 1 m to 0.7 m. The pressure intensity atthe center line of 1 m section is 8and rate of flow of water through the pipe is600 liters/s.,I. Find the intensity of pressure at the center line of 0.7 m section.II. Determine the force exerted by flowing water on transition of the pipe.
To what height will the jet of fluid rise for the conditions shown in the figure?
A water pump has an outlet diameter of 70 mm horizontal pipe flowing full at the outlet. The resulting jet strikes the ground surface at a horizontal distance of 32 m and a vertical distance of 1.75 m from the outlet. Find the pumping capacity in liters per minute.
find reynolds
As given in the figure, the water flowing into a tank at a constant speed will make the tank in 5 minutes h = It fills up to a height of 3 m. The long side of the rectangular warehouse is 2 m and short If the side is 1.5 m, the water at 30 ° C flowing from the 0.2 m diameter pipe at point A Calculate its average velocity as [m / s] and its flow rate as [kg / s]. (b) Water at 0.5 m / s It flows into the pipe at a constant average velocity. In this framework, h = 3 m deep warehouse The relationship between the time required to fill (t) and the pipe diameter at point A (D) Determine. (Take the width of the warehouse as 1.5 m). Plot the graph of t (minutes) vs.D (m). (D; Let it be located on the horizontal axis as 0.05 m, 0.1 m, 0.15 m, 0.20 m and 0.25 m).
the diameters of a tapering pipe at the sections 1-1 and 2-2 are 100 mm and 150 mm respectively. if the velocity of water flowing through the pipe at section 1-1 is 5 m/s, find discharge through the pipe and velocity of water at section 2-2
a) As given in the figure, water flowing into a tank at a constant speed fills the tank up to h = 3 m height in 5 minutes. If the long side of the rectangular tank is 2 m and the short side is 1.5 m, calculate the average velocity of the water at 30 ° C flowing from the 0.2 m diameter pipe at point A as [m / s] and its flow rate as [kg / s]. b) Water flows into the pipe at a constant average velocity of 0.5 m / s. In this framework, determine the relationship between the time (t) required to fill the tank at h = 3 m depth and the pipe diameter (D) at point A. (Take the width of the warehouse as 1.5 m). Plot the graph of (minutes) -D (m). (Let D be on the horizontal axis as 0.05 m, 0.1 m, 0.15 m, 0.20 m and 0.25 m)
A horizontal pipe is full of flowing water. At location A the velocity is 1.5 m/s and the pressure is 138 kN/m2. If the pipe tapers gradually from 150mm diameter at A to 100mm diameter at location B, determine the pressure of the water at B, assuming there is no loss of energy.
A pipe of diameter 400 mm carries water at a velocity of 25 m/s. The pressures at the points A and B are given as 29.43 N/cm2 and 22.563 N/cm2 respectively while the datum head at A and B are 28m and 30 m. Find the loss of head between A and B. Sketch the arrangement.
The diameter of a pipe at the section 1 and 2 are 10 cm and 15 cm respectively. Find the discharge through the pipe if the velocity of water flowing through the pipe at section 1 is 5m/sec. Determine the velocity at section 2.
A cylindrical tank discharges water at 20^O C through a well-rounded orifice to hit an inclined plate as shown in the figure. Determine the components of the force exerted by the fluid jet on the plate inclined at 60^O from the horizontal.( Assume the external and internal pressures are the same)
A tank has one of its side inclined inward at an angle of 30 degrees with horizontal. The free surface of the contained water is at Elev 15.25 m. The orifice located on the inclined side issues a jet, having its vena contracta at Elev 10.70 m. If the highest point in the trajectory of the jet is at Elev. 14.00m, find the actual velocity of the jet. Neglect air friction. Include Illustration if needed. a.9.3 m/s b.8.3 m/s c.10.3 m/s d.11.3 m/s