3- A steel shaft in a conveyor transmits 30 hp of power at 5 Hz. Determine the smallest safe diameter of the shaft to the nearest 1/8 inch if the shear stress Ț is not to exceed 6kpi and the angle of twist 0 is limited to 6°in a length of 10 ft. Use G = 12 x 106 psi. %3D

3- A steel shaft in a conveyor transmits 30 hp of power at 5 Hz. Determine the smallest safe diameter of the shaft to the nearest 1/8 inch if the shear stress Ț is not to exceed 6kpi and the angle of twist 0 is limited to 6°in a length of 10 ft. Use G = 12 x 106 psi. %3D

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter3: Torsion

Section: Chapter Questions

Problem 3.11.3P: A thin-walled aluminum tube of rectangular cross section (sec fig me) has a centerline dimensions b...

See similar textbooks

Related questions

Q: A solid shaft is required to transmit 120 kW power at 200 rpm. Find the suitable diameter of the…

A: Power, P = 120 kW Speed, N = 200 rpm Tmax = 1.2Tmean Shear stress, = 70 N/mm2…

Q: 3.31 A hollow steel shaft, 6 ft long, has an outer diameter of 3 in. and an i diameter of 1.5 in.…

Q: A hollow bronze shaft (G=5000ksi) has an outer diameter of 3in and a wall thickness of 0.25in. The…

A: Given data: Converting all data into SI units. Modulus of rigidity G=5000 ksi=34473.8 Mpa Outer…

Q: The shaft and the flange of a marine engine are to be designed for flange coupling, in which the…

Q: 3.13 The torques T and 2T are carried by a shaft consisting of steel and aluminum segments. If the…

A: Given:ζs=14,000 psiζa=7,500 psiθmax=8Gs=12*106 psiGa=4*106 psi

Q: A solid shaft is subjected to a twisting moment of 350 kNm. If the angle of twist is 5° per meter of…

Q: The figure shows an inboard engine, 8-ft long steel drive shaft, and propeller for a motor boat. The…

A: Given data: P=200 hpN=3500 rpmG=12×106 psiτ=12000 psi Need to determine the diameter of the smallest…

Q: The drive shaft for a truck (outer diameter 60 mm and inner diameter 40 mm) is running at 42 Hz. If…

Q: A 250 hp motor turns a shaft at 2400 rpm. The shaft steps down in diameter 3.0-in to 2.5-in as shown…

A: Given:Power of motor, P=250 hpShaft speed, N=2400 rpmDmax=3.0 inDmin=2.5 in

Q: 3.22 The compound shaft, composed of steel, aluminum, and bronze segments, carries the two torques…

Q: Problem 3. A solid circular shaft of steel is transmitting 20 kW of power at 120 rpm. Determine the…

Q: A solid shaft is required to transmit 90 kW of power at 200 rpm. Determine the shaft diameter by the…

A: The power P can be given by - P=90×1000=2πNT6090×1000= 2π×200×T60T=4297.18 NmThe shear stress can be…

Q: A cylindrical tube of constant wall thickness t and inside radius r % 10t carries a torque T. Find…

A: Given Data Inside radius of tube is : ri=14×10t=2.5t Inside diameter is : d=2×2.5t=5t Outside…

Q: For the cross-section shown below, computer the rate of twist and the shear stress if a torque of…

A: Torsion Torsion is a twisting of object when torque is applied on it. Torque Torque is a…

Q: A solid circular shaft of diameter 100 mm is subjected to an axial stress of 50 MPa. It is further…

A: Data given- d = 100 mm σaxial = 50 MPa T = 10 kN-m

Q: A hollow circular section shaft 2.5 m long is firmly supported at each end and has an inside…

Q: Q2/ A hollow shaft has to transmit 6MW at 150rev/min. The maximum allowable stress is not to exceed…

Q: Q.4. A solid steel shaft 5m long is stressed to 80 MPa when twisted through 4 degrees using G- 83…

Q: A mild steel shaft transmits P is 18 kW at N is 525 r.p.m. It carries a central load of 900 N and is…

Q: (a) the maximum shear stress in the shaft; and (b) the angle of twist in degrees. Use G =12 x 106…

Q: Q2: A solid steel shaft has a diameter of d and a length of L had used to transmit a power of 120 kW…

Q: : Q2 /A hollow steel shaft transmits 200 kw of power at 150 rpm .The total angle of twist in length…

Q: A hollow steel shaft, 12 m long, is required to transmit 1000 kW when running at a speed of 300…

A: Given that , L=12m =12000mm P=1000 kW =1000×106N-mm/s

Q: .A hollow steel shaft transmits 600 kW at 500 r.p.m. The maximum shear stress is 62.4 MPa. Find the…

A: We are authorized to answer one question at a time since you have not mentioned which question you…

Q: QUESTION The shaft consists of solid 160 mm diameter rod segment PQ and RS, and the tubular segment…

A: To find: The maximum allowable torque T can be applied to the shaft. Given: The inner diameter of…

Q: A shaft is required to transmit 285 kW power at 255 r.p.m. The maximum torque may be 1.8 times the…

Q: 4- A hollow tubular shaft is 1.5 m long and has an outer diameter of 75-mm. The shaft transmits the…

Q: A hollow shaft for marine applications has outer and inner diameters of 400 mm and 200 mm…

A: Given: The outer diameter of shaft, D = 400 mm = 0.4 m The inner diameter of shaft, d = 200 mm = 0.2…

Q: 3.30 A solid steel shaft transmits 20 hp while running at 120 rev/min. Find the smallest safe…

Q: QUESTION 2: 2.1 A shaft is to transmit 190 kW at 180 rev/min. If the maximum torque transmitted is…

Q: 12 A line shaft ABCD, 9 metres long, has four pulleys A, B, C and D at equal distance apart. Power…

A: Given Data:N=630 rpmζmax=55 MpaG=85 GpaTo Find :1dAB2dBC3dCD4θD/A

Q: 2 A hollow simple supported shaft 3m made of steel with di/do of 0.6. e shaft is subjected to a…

Q: A hollow shaft and a solid shaft constructed of the same material have the same length and the same…

A: Solution-2 The general relation between torque, shear stress, angle of twist of a shaft under…

Q: Find the diameter of the shaft (based on torsional stiffness) for which the angle of twist is not to…

Q: Q2 /A hollow steel shaft transmits 200 kw of power at 150 rpm .The total angle of twist in length of…

Q: 3.43 A steel tube with the cross section shown carries a 50-kip in. torque. Determine (a) the…

A: Answer: (a) The maximum shear stress in the tube is 15300 psi. (b) The angle of twist per foot of…

Q: 1) A solid steel drive shaft is required to transmit 12 hp. The allowable shear stress for steel is…

Q: A shaft transmits 20 kW power and rotates at 500 rpm. The material of the shaft is 50C4 (ơvp = 460…

A: Given, Power transmitted = P = 20 kW = 20,000 W Shaft RPM = N = 500 rpm Yield strength of shaft =…

Q: 3. Shafts AB and BC (each 50 mm long) are welded to each other. Shaft AB is hallow with 20 mm inner…

A: Given dataLength of the shaft AB and BC = 50mmShaft AB inner raius ri = 20mmShaft AB outer radius ro…

Q: A steel shaft in the form of a solid body circular rod or a circular tube can be manufactured. The…

A: given torsional torque T=1200 N.mshear stress for shaft material τ= 40 MPalargest permissible unit…

Q: Torsional Loadings A hollow tube having an outside diameter and inside diameter of 100mm and 80mm…

A: Given:do=100 mmdi=80 mmL=250 mmG=28 GPa

Q: A solid shaft has to transmit 120 kW of power at 160 rpm. If the shear stress is not to exceed 60…

Q: Q3.An electric motor is connected to a turbine with the help of a hollow shaft. The hollow shaft has…

Q: A solid circular shaft of steel is transmitting 20 kW of power at 120 rpm. Determine the minimum…

Q: A rod is made from two segments: AB is steel and BC is brass. It is fixed at its ends and subjected…

Q: Prob. # 3] The torsional deformation of a steel shaft is 1° in a length of 2 ft when the shearing…

A: Given data, L= 2ft= 24in. θ= 1°= 0.0174533 rad S= 10000 psi G= 12*10⁶ psi

Q: T 100 mm 70 mm 70 mm 1.5 m 2 m T

Q: n 66 mm diameter alloy shaft is 6.5 m long and subjected to twisting. The shaft is attached to a…

A: Given: The overall length, L = 6.5 m The shear modulus, G = 81 GPa Teh diameter of shaft, d = 66 mm…

Q: 2) The minimum outer diameter required for a hollow shaft if the shaft inner stress of tallow= 75…

Q: A steel shaft with a diameter 45 mm and length 1.30 m transmits 55.50 kW from an electric motor to a…

A: Given data Diameter of shaft = d= 45 mm = 0.045 mLength of shaft =l = 1.30 mPower Delivered =P =…

Q: A shaft is transmitting 100 kW at 180 r.p.m. If the allowable stress in the material is 60 MPa, find…

A: Answer: The suitable diameter of the shaft is 105 mm.

Q: A hollow shaft has to transmit 6 MW at 150 rev/min. The maximum allowable stress is not to exceed 60…

Q: An 66 mm diameter alloy shaft is 6.5 m long and subjected to twisting. The shaft is attached to a…

Q: 7. A shaft made of mild steel is required to transmit 100 kW at 300 r.p.m. The supported length of…

A: We have to determine diameters of the shaft

Q: A hollow nickel steel shaft with outside diameter is twice the inside diameter is to transmit 1492…

Q: 1) Design a cast iron protective flange coupling to connect two shafts in order to transmit 7.5 kW…

A: Given dataPower trasmitted by the shaft P = 7.5kWPerimssible shear stress for the shaft,bolt and key…

Q: Q2/ A hollow shaft has to transmit 6MW at 150rev/min. The maximum allowable stress is not to exceed…

Q: 1. A flange coupling connects two shafts to transmit 40 kW at 900 rpm. The flanges of the coupling…

Q: Q3-C- The 304 stainless steel shaft with modulus of rigidity 75 GPa and 3 m long has an outer…

A: Calculated the smallest thickness of shaft.

Concept explainers

Pressure Vessels

The term pressure vessel refers to a closed container that contains gas or liquid at a different pressure than environment pressure. The pressure vessels have a wide scale of applications in our day-to-day lives and other industrial places. Some common examples of pressure vessels are gas cylinders, autoclaves, compressor vessels, etc.

Question

3- A steel shaft in a conveyor transmits 30 hp of power at 5 Hz.
Determine the smallest safe diameter of the shaft to the
nearest 1/8 inch if the shear stress Ț is not to exceed 6kpi and
the angle of twist 0 is limited to 6°in a length of 10 ft. Use G =
12 x 106 psi.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

A propeller shaft for a small yacht is made of a solid steel bar 104 mm in diameter. The allowable stress in shear is 48 MPa, and the allowable rate of twist is 2.0° in 3.5 meters. (a) Assuming that the shear modulus of elasticity is G = 80 GPa, determine the maximum torque that can be applied to the shaft. (b) Repeat part (a) if the shaft is now hollow with an inner diameter of 5d18. Compare values to corresponding values from part (a).
The stepped shaft shown in the figure is required to transmit 600 kW of power at 400 rpm. The shaft has a full quarter-circular fillet, and the smaller diameter D1= 100 mm. If the allowable shear stress at the stress concentration is 100 MPa, at what diameter will this stress be reached? Is this diameter an upper or a lower limit on the value of D2?
A thin-walled rectangular tube has uniform thickness t and dimensions a x b to the median line of the cross section (see figure). How does the shear stress in the tube vary with the ratio = a/b if the total length Lmof the median line of the cross section and the torque T remain constant? From your results, show that the shear stress is smallest when the tube is square (ß = 1).
The propeller shaft of a large ship has an outside diameter 18 in. and inside diameter 12 in,, as shown in the figure. The shaft is rated for a maximum shear stress of 4500 psi. If the shaft is turning at 100 rpm, what is the maximum horsepower that can be transmitted without exceeding the allowable stress? If the rotational speed of the shaft is doubled but the power requirements remain unchanged, what happens to the shear stress in the shaft?
A thin-walled aluminum tube of rectangular cross section (sec fig me) has a centerline dimensions b = 6.0 in. and b = 4.0 in. The wall thickness t is constant and equal to 0.25 in. Determine the shear stress in the tube due to a torque T = 15 kip-in. Determine the angle of twist (in degrees) if the length L of the tube is 50 in. and the shear modulus G is 4.0 x 106 psi.
What is the maximum power that can be delivered by a hollow propeller shaft (outside diameter 50 mm, inside diameter 40 mm, and shear modulus of elasticity 80 GPa) turning at 600 rpm if the allowable shear stress is 100 MPa and the allowable rate of twist is 3.0°/m?
A stepped shaft ACB having solid circular cross sections with two different diameters is held against rotation at the ends (sec figure). If the allowable shear stress in the shaft is 6000 psi, what is the maximum torque (T0) that may be applied at section C? Find (T0)max if the maximum angle of twist is limited to 0.55º. Let G = 10,600 ksi.
A tubular shaft being designed for use on a construction site must transmit 120 kW at 1,75 Hz, The inside diameter of the shaft is to be one-half of the outside diameter. If the allowable shear stress in the shaft is 45 MPa, what is the minimum required outside diameter d?
A circular aluminum tube subjected to pure torsion by torques T(sec figure) has an outer radius r2equal to 1.5 times the inner radius r1. (a) If the maximum shear strain in the tube is measured as 400 × 10-6 rad, what is the shear strain y1at the inner surface? (b) If the maximum a1lo-abk rate of twist is 0.125 °/m and the maximum shear strain is to be kept at 400 × 10-6 rad by adjusting the torque T, that is the minimum required outer radius ( r2)Min?
Solve the preceding problem if the length L = 56 in., the inner radius r1— 1.25 in., the angle of twist is 0.5°, and the allowable shear strain is 0.0004 rad.
Solve the preceding problem if the stress and dimensions aallow = 2450 pai, L = 80 in., b = 2.5 in,, h = 10 in., and d = 2.5 in
A copper tube with circular cross section has length L = 1.25 m, thickness t = 2 mm, and shear modulus of elasticity G = 45 GPa. The bar is designed to carry a 300 N·m torque acting at the ends. If the allowable shear stress is 25 MPa and the allowable angle of twist between the ends is 2.5°, what is the minimum required outer diameter d?