Please help me with this question its urgen QUESTION 2:2.1 A shaft is to transmit 190 kW at 180 rev/min. If the maximum torque transmitted is 50%more than the mean torque, the shear stress should not exceed 45 MPa nor an angle oftwist of greater than 1.2° per metre length. Determine the required diameter if:2.1.1 The shaft is solid2.1.2 The shaft is hollow with the ratio of inner to outer diameters of 3:5. Take modulus ofrigidity=80 GPa.2.2 A compound steel shaft is formed by attaching a solid and a hollow shaft as shown inbelow figure. The maximum allowable shear stress in the shaft should not exceed 70 MPaand the total angle of twist should not exceed 2.08°. If the length x is 2.28 m and thelength y is 1.69 m, calculate for a value of G-83 GPa:2.2.1 The magnitude of the allowable maximum torque2.2.2 The angle of twist of the hollow shaft.2.2.3 The stiffness of each shaft.100 mm70 mmC70 mmy

Answered: Image /qna-images/answer/7b67bf4f-e500-43ac-81e5-918f23268704.jpg

QUESTION 2: 2.1 A shaft is to transmit 190 kW at 180 rev/min. If the maximum torque transmitted is 50% more than the mean torque, the shear stress should not exceed 45 MPa nor an angle of twist of greater than 1.2° per metre length. Determine the required diameter if: 2.1.1 The shaft is solid 2.1.2 The shaft is hollow with the ratio of inner to outer diameters of 3:5. Take modulus of rigidity=80 GPa.

QUESTION 2: 2.1 A shaft is to transmit 190 kW at 180 rev/min. If the maximum torque transmitted is 50% more than the mean torque, the shear stress should not exceed 45 MPa nor an angle of twist of greater than 1.2° per metre length. Determine the required diameter if: 2.1.1 The shaft is solid 2.1.2 The shaft is hollow with the ratio of inner to outer diameters of 3:5. Take modulus of rigidity=80 GPa.

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter3: Torsion

Section: Chapter Questions

Problem 3.3.19P: A solid brass bar of diameter d = 1.25 in. is subjected to torques T1as shown in part a of the...

See similar textbooks

Similar questions

A propeller shaft for a small yacht is made of a solid steel bar 104 mm in diameter. The allowable stress in shear is 48 MPa, and the allowable rate of twist is 2.0° in 3.5 meters. (a) Assuming that the shear modulus of elasticity is G = 80 GPa, determine the maximum torque that can be applied to the shaft. (b) Repeat part (a) if the shaft is now hollow with an inner diameter of 5d18. Compare values to corresponding values from part (a).
A tubular shaft being designed for use on a construction site must transmit 120 kW at 1,75 Hz, The inside diameter of the shaft is to be one-half of the outside diameter. If the allowable shear stress in the shaft is 45 MPa, what is the minimum required outside diameter d?
What is the maximum power that can be delivered by a hollow propeller shaft (outside diameter 50 mm, inside diameter 40 mm, and shear modulus of elasticity 80 GPa) turning at 600 rpm if the allowable shear stress is 100 MPa and the allowable rate of twist is 3.0°/m?
A solid brass bar of diameter d = 1.25 in. is subjected to torques T1as shown in part a of the figure. The allowable shear stress in the brass is 12 ksi. What is the maximum permissible value of the torques T1? If a hole of diameter 0.625 in. is drilled longitudinally through the bar, as shown in part b of the figure, what is the maximum permissible value of the torques T2? What is the percent decrease in torque and the percent decrease in weight due to the hole?
A circular aluminum tube subjected to pure torsion by torques T(sec figure) has an outer radius r2equal to 1.5 times the inner radius r1. (a) If the maximum shear strain in the tube is measured as 400 × 10-6 rad, what is the shear strain y1at the inner surface? (b) If the maximum a1lo-abk rate of twist is 0.125 °/m and the maximum shear strain is to be kept at 400 × 10-6 rad by adjusting the torque T, that is the minimum required outer radius ( r2)Min?
A Solid shaft transmits 600 N.m torque. If the maximum shear stress induced in the shaft is 50 N/mm2, the minimum diameter of the shaft is
A 3-meter solid steel shaft, with an unknown diameter, twists by 5° as it experienced a shear stress of 60 MPa. What is the diameter of the solid steel shaft? Use G = 83 GPa.
A solid shaft in a rolling mill transmits 30 hp at 100 rpm. Find the diameter in mm of the shaft so as not to exceed a shearing stress of 42 MPa and an angle of twist of more than 5 degrees in a length of 3 meters. G = 83 GPa
Bearing stress 4. Please provide proper discussion and illustration also complete solution and clear solution please thank you Determine the length of a square key to be used for a 3.73 kW, 1800 rpm electric motor if the motor shaft diameter is 35 mm and the width of the key is approximately one-fourth of the shaft diameter. The allowable shearing stress on the key is 2.45 MPa
Q2. A mild steel shaft transmits ‘P’ kW at ‘N’ r.p.m. It carries a central load of 900 N and is simply supported between the bearings 2.5 metres apart. Determine the size of the shaft, if the allowable shear stress is 42 MPa and the maximum tensile or compressive stress is not to exceed 56 MPa. Power P in KW= 25 , Speed N in rpm=150
A steel shaft with a diameter of 40 mm and the length of 1.1 m transmits 60 hp from an electric motor to a compressor. If the allowable shear stress is 50 MPa and the allowable angle of twist is 1.50, what is the minimum allowable speed of rotation.
A solid shaft in a rolling mill transmits 20 kW at 2 revolutions per second. The length of the shaft is 3 m and modulus of rigidity is 83,000 MPa. Which of the following gives the torque carried by the shaft?a. 1.59 kN-m c. 2.69 kN-mb. 3.45 kN-m d. 4.81 kN-m Which of the following gives the minimum diameter so that the allowable torsional shearing of 40 MPa will not beexceeded?a. 88 mm c. 59 mmb. 45 mm d. 76 mm Which of the following gives the minimum diameter so that the allowable angle of twist of 6O will not be exceeded?a. 29 mm c. 35 mmb. 49 mm d. 55 mm