i need the answer quickly 9.8 (B). A thin cylinder of 300 mm internal diameter and 12 mm thickness is subjected to an internal pressurep while the ends are subjected to an external pressure of p. Determine the value of pat which elastic failure will occuraccording to (a) the maximum shear stress theory, and (b) the maximum shear strain energy theory, if the limit ofproportionality of the material in simple tension is 270 MN/m?. What will be the volumetric strain at this pressure?E = 210 GN/m2; v 0.3[21.6, 23.6 MN/m², 2.289 x 10-3, 2.5 x 10-3.]

Given: The internal diameter of the thin cylinder, d=300 mm or 0.3 m The thickness of the cylinder,…

3 (B). A thin cylinder of 300 mm internal diameter and 12 mm thickness is subjected to an internal pressure ile the ends are subjected to an external pressure of }p. Determine the value of pat which elastic failure will occur rding to (a) the maximum shear stress theory, and (b) the maximum shear strain energy theory, if the limit of ortionality of the material in simple tension is 270 MN/m². What will be the volumetric strain at this pressure? 210 GN/m2; v 0.3 [21.6, 23.6 MN/m², 2.289 x 10-3, 2.5 x 10-3.]

3 (B). A thin cylinder of 300 mm internal diameter and 12 mm thickness is subjected to an internal pressure ile the ends are subjected to an external pressure of }p. Determine the value of pat which elastic failure will occur rding to (a) the maximum shear stress theory, and (b) the maximum shear strain energy theory, if the limit of ortionality of the material in simple tension is 270 MN/m². What will be the volumetric strain at this pressure? 210 GN/m2; v 0.3 [21.6, 23.6 MN/m², 2.289 x 10-3, 2.5 x 10-3.]

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter8: Applications Of Plane Stress (pressure Vessels, Beams, And Combined Loadings)

Section: Chapter Questions

Problem 8.2.12P: Solve the preceding problem if the diameter is 480 mm, the pressure is 20 MPa, the yield stress in...

See similar textbooks

Similar questions

A wine of length L = 4 ft and diameter d = 0.125 in. is stretched by tensile forces P = 600 lb. The wire is made of a copper alloy having a stress-strain relationship that may be described mathematically by =18,0001+30000.03(=ksi) in which is nondimensional and has units of kips per square inch (ksi). (a) Construct a stress-strain diagram for the material. (bj Determine the elongation, of the wire due to the Forces P. (c) IF the forces are removed, what is the permanent set of the bar? (d) If the forces are applied again, what is the proportional limit?
The rails of a railroad track are welded together at their ends (to form continuous rails and thus eliminate the clacking sound of the wheels) when the temperature is 60°F. What compressive stress ?? =6.5×10-6 /? is produced in the rails when they are heated by the sun to 120"F if the coefficient of thermal expansion a = the modulus of elasticity E = 30 × 106 psi?
(a) Solve part (a) of the preceding problem if the pressure is 8.5 psi, the diameter is 10 in., the wall thickness is 0,05 in., the modulus of elasticity is 200 psi, and Poisson's ratio is 0.48. (b) If the strain must be limited to 1.01, find the maximum acceptable inflation pressure
A brass plate with a modulus of elastici ty E = 16 X 106 psi and Poisson’s ratio a = 0.34 is loaded in biaxial stress by normal stresses r and cry. (sec figure). A strain gage is bonded to the plate at an angle 4 = 350 If the stress o is 10,700 psi and the strain means used by the gageise = 390 X 106.whatisthcmax- imum in-plane shear stress (Tr, ),. and shear strain (>‘ ).? What is the maximum shear strain (y ) in the x-: plane? What is the maximum shear strain (y ).. in the y-r plane?
Solve the preceding problem if the diameter is 480 mm, the pressure is 20 MPa, the yield stress in tension is 975 MPa, the yield stress in shear is 460 MPa, the factor of safety is 2,75, the modulus of elasticity is 210 GPa, Poissorfs ratio is 0.28, and the normal strain must not exceed 1190 x 10" . For part (b), assume that the tank thickness is 8 mm and the measured normal strain is 990 x 10~ .
(d) Define Modulus of Resilience 2. Draw the stress-strain diagram for a typical ductile material and locate the salient points onit 3. A bar of 25 mm diameter is tested in tension. It is observed that when a load of 60 kN is applied, the measured over a gauge length of 200 mm is 0.12 mm and contraction in diameter is 0.0045 mm. Find Poissa 4. A circular rod of diameter 16 mm and 500 mm long is subjected to a tensile force 40 kN. The modulus of e steel may be taken as 200 kN/mm?. Find the elongation and strainin the bar due to applied load. 5. Define (a) Resilience (b) Proof resilience PART -B structions: Part B consists of 3 Units. Answer any one full question from each unit. Each questioncarries 8 marks and may have su 1. A steel circular bar has three segments as shown in the fig. Determine the total elongation ofthe bar. Take E = 210 GPa. 300 kNI 330 kN 30 mm 50KN 15 mm 20 mm 80 kN A + 150 mm 200 mm 250 mm B. D (OR)
9.8 A thin cylinder of 300 mm internal diameter and 12 mm thickness is subjected to an internal pressure p, while the ends are subjected to an external pressure of 1/2 p. Determine the value of p at which elastic failure will occur according to (a) the maximum shear stress theory, and (b) the maximum shear strain energy theory, if the limit of proportionality of the material in simple tension is 270 MN/m?. What will be the volumetric strain at this pressure? E = 210 GN/m2; v = 0.3.
A specimen of titanium alloy is tested in torsion and the shear stress–strain diagram is shown in Fig.a. Determine the shear modulus G, the proportional limit, and the ultimate shear stress. Also, determine the maximum distance d that the top of a block of this material, shown in Fig. b, could be displaced horizontally if the material behaves elastically when acted upon by a shear force V. What is the magnitude of V necessary to cause this displacement?
1. A steel pipe of length 4 ft, outside diameter of 6.0 in., andinside diameter of 4.5 in., is compressed by an axial forceof 140 kips. The material has a modulus of elasticity of30,000 ksi and Poisson’s ratio of 0.30. Determine thefollowing quantities for the pipe:a. The shortening.b. The lateral strain.c. The percentage increase in the outer and theincrease in the inner diameter.d. The percentage increase in the wall thickness.
At a point in a bar of cast iron, the principal stresses are 60 MPa tensile and 120 MPa compressive whereas the third principal stress is zero. Find the factorsof safety based on the elastic limit when the criterion of failure is principal stress theory. Assume the elasticlimit of cast iron is 90 MPa in tension and 440 MPa in compression
Question 4 A steel rod of 20 mm diameter passes centrally through a copper tube of 50 mm external diameter and 40 mm internal diameter. The tube is closed at each end by rigid plates of negligible thickness. The nuts are tightened lightly home on the projecting parts of the rod. If the temperature of the assembly is raised by 50°C, calculate the stresses developed in copper and steel. Take E for steel and copper as 200 GN/m² and 100 GN/m² and a for steel and copper as 12x 10-6 per °C and 18 x 10-6 per °C.
a)Draw the stress-strain curve of a ductile material such as that of a ductile steel and discuss the various regions of the curve. Explain the difference between a ductile and brittle material and the concept of ductility and its measurement. b)A machine part 10 mm thick, having the dimensions shown in the figure, is to be subjected to cyclic loading. If the maximum stress is limited to 60 MPa, determine the allowable force P. Approximate the stress concentration factors form the graph given. Where might a potential fracture occur?