Determine the elastic tensile load "F" that acts on mild steel specimen of Diameter 7 mm & Modulus of Elasticity 193 GPa. It is found that the specimen has undergone an extension of 1.1 mm due to the elastic load "F". Also, determine the length "L" of the specimen, if the strain- induced due to the load "F" on the specimen is 4.5 x 10-3. Solution Cross-sectional Area, A (in mm²) Tensile Load, F (in N) Length of the Specimen (in mm)

Determine the elastic tensile load "F" that acts on mild steel specimen of Diameter 7 mm & Modulus of Elasticity 193 GPa. It is found that the specimen has undergone an extension of 1.1 mm due to the elastic load "F". Also, determine the length "L" of the specimen, if the strain- induced due to the load "F" on the specimen is 4.5 x 10-3. Solution Cross-sectional Area, A (in mm²) Tensile Load, F (in N) Length of the Specimen (in mm)

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter7: Analysis Of Stress And Strain

Section: Chapter Questions

Problem 7.7.4P: An element of material in plain strain is subjected to strains x = 0.0015, , y . = -0.0002, and xy =...

See similar textbooks

Similar questions

Determine the strain energy per unit volume (units of psi) and the strain energy per unit weight (units of in ) that can be stored in each or the materials listed in the accompanying table, assuming that the material is stressed to the proportional limit. DATA FOR PROBLEM 2.7-5 Material Weight Density (lb/in3) Modulus of Elasticity (ksi) Proportional Limit (psi) Mild sleel 0.284 30,000 36,000 Tool steel 0.284 30,000 75,000 Aluminum 0.0984 10,500 60,000 Rubber (soft) 0.0405 0.300 300
A thin square plate in biaxial stress is subjected to stresses ?? and ??., as shown in part a of the figure. The width of the plate is h = 12.0 in. Measurements show that the normal strains in the x and v directions are s = 427 × 10-6 and s = 113 × l0-6, respectively. With reference to part b of the figure. which shows a Iwo-dimensional view of the plate. determine the following quantities. (a) The increase .d in the length of diagonal Oil. (b) The change . in the angle between diagonal Oti and the x axis, (c) The shear strain y associated with diagonals Oil and cf(that is. find the decrease in angle ced).
An element of material in plain strain is subjected to strains x = 0.0015, , y . = -0.0002, and xy = 0.0003. (a) Determine the strains for an element oriented at an angle = 20°. (b) Determine the principal strains of the element. Confirm the solution using Mohr’s circle for plane strain.
On the surface of a structural component in a space vehicle, the strains arc monitored by means of three strain gages arranged as shown in the figure. During a certain maneuver, the following strains were recorded: e, = 1100 X l0_6, 6h = 200 X lO_6, and e = 200 X 10-6. Determine the principal strains and principal stresses in the material. which is a magnesium alloy for which E = 6000 ksi and v = 0.35. Show the princ ipal strains and principal stresses on sketches of properly oriented elements.
The elastic portion of the stress–strain diagram for an aluminum alloy is shown in the figure. The specimen from which it was obtained has an original diameter of 12.7 mm andagagelengthof50.8mm.IfaloadofP=60kNisapplied to the specimen, determine its new diameter and length. Take n = 0.35.
A tension specimen of circular cross-section tapers uniformly from 20 mmto 16 mm diameter over a gauge length of 200 mm. When an axial load of40 JcN is applied, the extension measured on this gauge length is 0-4 mm. Findthe modulus of elasticity of the material.Compare the strain energy in this specimen with that in a specimen of thesame material of uniform diameter 18 mm carrying the same load. (U. Lond.)
The diameter (d) of a solid rod (i.e., with a circular cross-section) is 16 mm and ismade from a homogeneous material. The length (L) of the rod is 1.75 m andYoung’s Modulus for the material (E) is 250 GPa. When the rod is placed undertension it experiences deformation and a stress (?) of 650 MPa. Calculate thefollowing:(i) Strain energy (U) to 2 decimal places in Joules.(ii) Strain energy per unit volume (U/V) in J/m3.(iii) The change in length ∆L to 2 decimal places in mm.(iv) The strain (?) due to deformation to 2 significant figures
The rod of 120cm long and 18mm diameter subjected to axial pull of 18kN. If modulus of Diameter = 30mm Axial Pull =30kN Elasticity for rod is 2x105 N/mm2. Determine Stress Strain Elongation of rod
A material is subjected to a general state of planestress. Express the strain energy density in terms of theelastic constants E, G, and n and the stress components sx,sy, and txy.
A specimen is originally 1.5 ft long, has a diameter of 0.7 in., and is subjected to a force 550 lb. When the force is increased to 1900 lb, the specimen elongates 0.9 in. Determine the strain on the specimen and the modulus of the material. a. Strain Answer: _______ in./in. b. Modulus of Elasticity Answer: _______ ksi
A tensile bar is stressed to 250 N/mm2 which is beyond its elastic limit. At this stage the strain produced in the bar is observed to be 0.0014. if the modulus of elasticity of the material of the bar is 205000 N/mm2 then the elastic component of the strain is very close toa. 0.0004b. 0.0002c. 0.0001d. 0.00005 PLS EXPLAIN YOUR ANSWER THOROUGHLY
If the Young's modulus and Poisson's ratio of the container material are 100 GPa and 0.3 respectively, What is the axial strain in the cylinder wall at mid-depth?