3 EW) 24. A centrifugal clutch has four blocks which slide radially in a spider keyed to the driving shaft and make contact with the internal cylindrical surface of a drum keyed to the driven shaft. When the clutch is at rest each block is pulled against a stop by a spring so as to leave a radial clearance of 6 mm between the block and the drum. The pull exerted by the spring is then 450 N and the mass centre of the block is 200 mm from the axis of the clutch. If the internal diameter of the drum is 500 mm, the mass of each block is 7 kg, the stiffness of each spring is 35 kN/m and the coefficient of friction between block and drum is 0-3, find the maximum power the clutch can transmit at 500 rev/min. (I. Mech. E.) (Ans.: 51-7 kW)

3 EW) 24. A centrifugal clutch has four blocks which slide radially in a spider keyed to the driving shaft and make contact with the internal cylindrical surface of a drum keyed to the driven shaft. When the clutch is at rest each block is pulled against a stop by a spring so as to leave a radial clearance of 6 mm between the block and the drum. The pull exerted by the spring is then 450 N and the mass centre of the block is 200 mm from the axis of the clutch. If the internal diameter of the drum is 500 mm, the mass of each block is 7 kg, the stiffness of each spring is 35 kN/m and the coefficient of friction between block and drum is 0-3, find the maximum power the clutch can transmit at 500 rev/min. (I. Mech. E.) (Ans.: 51-7 kW)

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Question 6: A mass of 0.2kg is attached to a spring with a spring constant of 5N/m. What should be the maximum value of the friction coefficient (b) for underdamping motion
An eight-cylinder, four-stroke engine of 9 cm bore and 8 cm stroke with a compressionratio of 7 is tested at 4500 rev/min on a dynamometer which has 54 cm arm. During a 10minutes test the dynamometer scale beam reading was 42 kg and the engine consumed4.4 kg of gasoline having a calorific value of 44000 kJ/kg. Air at 27C and 1 bar wassupplied to the carburettor at the rate of 6 kg/min. Take R for air = 287 kJ/(kg·K). Find:(1) the brake power delivered (bp),(2) the brake mean effective pressure (bmep),(3) the brake specific fuel consumption (bsfc),(4) the brake specific air consumption (bsac),(5) the brake thermal efficiency (b, th),(6) the volumetric efficiency (vol), and(7) the air-fuel ratio (A/F) on mass basis.Draw the simplified schematic diagram of the plant showing all the necessary data displayed on it. "Please only draw on schematic diagram of the plant"
An eight-cylinder, four-stroke engine of 9 cm bore and 8 cm stroke with a compressionratio of 7 is tested at 4500 rev/min on a dynamometer which has 54 cm arm. During a 10minutes test the dynamometer scale beam reading was 42 kg and the engine consumed4.4 kg of gasoline having a calorific value of 44000 kJ/kg. Air at 27C and 1 bar wassupplied to the carburettor at the rate of 6 kg/min. Take R for air = 287 kJ/(kg·K). Find: (4) the brake specific air consumption (bsac),(5) the brake thermal efficiency (b, th),(6) the volumetric efficiency (vol), and(7) the air-fuel ratio (A/F) on mass basis.Draw the simplified schematic diagram of the plant showing all the necessary data displayed on it.
For a 90° V-twin engine system, having two identical cylinder with center line of each cylinder being inclined at 45° to vertical, the speed is 2400 rpm. The reciprocuting mass per cylinder - 1.5 kg stroke=14 cm length of connecting rod -28 cm. Find the values of max. primary and secondary Forces and indicate whether the same the can be balanced by suitable means.
A 5-feet diameter Chimney is designed to handle a flue gas produced in a steam power plant at a rate of 17 lb/s. The barometric pressure is 29.92-inch Hg. Outside air enters the combustion chamber at 90 F. The average temperature of the flue gas inside the Chimney is 572 F and its molecular weight is 30. Cv = 0.35, Rair = 53.342 ft-lb/lb-R. Calculate: 5. The total draft, feet of air. 6. The height of the Chimney, feet
The compressor shown has a mass of 250 kg and operates at 2000 rpm. At this operating condition, the force transmitted to the ground is excessively high and is found to be mrw2f. where mr is the unbalance and wf is the forcing frequency. To fix this problem, it is proposed to isolate the compressor by mounting it on a square concrete block separated from the rest of the floor as shown. The density of concrete is 2400 kg/m3 and the spring constant for the soil is found to be 80 × 106 N/m. The geometry of the compressor leads to choosing a block that is 1.5 m by 1.5 m. Determine the depth h that will reduce the force transmitted to the ground by 75 percent.
A selfpropelled truck of total mass 25 tonnes and wheel diameter 750 mm runs on a track forwhich the resistance is 180 N per tonne. The engine develops 60 kW at its maximum speed of 2400r.p.m. and drives the axle through a gear box. Determine : 1. the time to reach full speed from reston the level if the gear reduction ratio is 10 to 1 Assume the engine torque to be constant and agearing efficiency of 94 per cent, and 2. the gear ratio required to give an acceleration of 0.15 m/s2on an up gradient of 1 in 70 assuming a gearing efficiency of 90 per cent.
A hydraulic lift is required to lift a load of 98.1 kN through a height of 12 m, once in every 100 seconds. The speed of the lift is 600 mm/s. Determine : (a) power required to drive the lift, (b) working period of lift in seconds, and (c) idle period of the lift in seconds. [Ans. (a) 11.772 kW, (b) 20 sec, (c) 80 sec]
3kg mass. P= 155N and w=0
The turning moment diagram for a multi cylinder engine has been drawn toa scale of 1 mm = 4500 N -m vertically and 1 mm = 2. 4 ͦ horizontally. Theintercepted areas between output torque curve and mean resistance lineabove and below the mean taken in order from one end are 342, 23, 245,303, 115, 232, 227, 164 ??2, when the engine is running at 150 rpm. Ifthe mass of the flywheel is 1000 kg and the total fluctuation of speed doesnot exceed 3% of the mean speed, find the minimum value of the radius ofgyration.
An eight-cylinder, four-stroke engine of 9 cm bore and 8 cm stroke with a compression ratio of 7 is tested at 4500 rev/min on a dynamometer which has 54 cm arm. During a 10 minutes test the dynamometer scale beam reading was 42 kg and the engine consumed 4.4 kg of gasoline having a calorific value of 44000 kJ/kg. Air at 27C and 1 bar was supplied to the carburettor at the rate of 6 kg/min. Take R for air = 287 kJ/(kg·K). Find: (1) the brake power delivered (bp), (2) the brake mean effective pressure (bmep), (3) the brake specific fuel consumption (bsfc), (4) the brake specific air consumption (bsac), (5) the brake thermal efficiency (b, th), (6) the volumetric efficiency (vol), and (7) the air-fuel ratio (A/F) on mass basis. Draw the simplified schematic diagram of the plant showing all the necessary data dis- played on it. ______
what is the effect of 1- gravity (g), 2- (m/l) on the value of the rate or spring constant (K)