answer question 2 show complete solution VaABсDQ2Q41. The linear velocity of A is represented by Va. Determine the linear velocitiesof B,C, and D on link 3 by the Instantaneous axis method. Q2A= 2 1/8"; AB= 1 13/16"; BC = 1 1/8" ; AD = 1 3/16"; BD = 1 7/16"; Q4B = 2 5/16"; Q2Q4=4"; Va= ft /sec. Kv= 1 inch: 5 ft/sec.2. Find a mechanism and which could best represent the Instantaneousmethod. Assume the Driver Crank Velocity to 5 ft/sec with a Kv= 1 inch:10 ft/sec.

Answered: Image /qna-images/answer/39bb4bcf-73b4-4417-bae5-1d8bfc12dfc3.jpg

Answered: 3 he linear velocity of A is…

3 he linear velocity of A is represented by Va. Determine the linear velocit fB,C, and D on link 3 by the Instantaneous axis method. Q2A= 2 1/8"; /

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

(Figure 3 shows a part of a system consisting of three slider blocks A, B, and C connected to rod AB and CE. Rod AB and CE are pinned at point D. The block A is moving upward at velocity. V₁ = 5 m/s.) a) (Determine the velocities of block B and point D. Draw the kinematic diagram of rod AB.) b) (Determine the velocities of block C and point E. Draw the kinematic diagram of rod CE.)
! SHOW FULL SOLUTION ! *PLS ANSWER ASAP NOTE: Block E is moving downward with a velocity of 4m/s. Determine the Velocity of Cable at Point C. Determine the Velocity of block W. Determine the Relative Velocity of Point C with respect to Block E. Determine the Relative Velocity of Block W with respect to Block E.
The power of an engine running at 125 rpm is turned off and the engine comes to rest at the end of 2 min and 40 sec. Assuming that there is no slipping between the belt and pulley surface and that the deceleration is uniform, find 1) the average speed in radians per second of the engine pulley in coming to rest; 2) the total angular distance traveled in revolutions, radians and degrees in coming to rest; 3) the distance in feet traveled by a belt running on the pulley in coming to rest, if the pulley diameter is 3ft.
A flywheel rotates with a uniform speed of 111rpm for 6.1 seconds .Then it is uniformly accelerated at 0.2rad/s2 for next 7.3 s. then it is made to stop in next 4.5s. Determine (i)maximum angular velocity; (ii) total angular displacement. 1.The angular displacement in rad θ1 = 2.The angular displacement in rad θ2 = 3.The maximum velocty in rad/s ω2= 4.The initial velocity in third case in rad/s ω03= 5.The angular displacement in third case in rad θ3= 6.The total displacement in rad θ=
Determine the velocity of Block D assuming link 2 is moving at 5 rad/s. The image is to scale with the indicated 4.5 cm
Show complete solution A particle rotates clockwise in accordance with the equation θ = 32 + 24t – 2t^3 where θ is in radians and t in seconds.a) Determine the time in seconds the particle passes the origin. b) Determine the maximum angular velocity
The graph below shows the acceleration of a hydraulic elevator in a four story school building as a function of time:- The graph begins at t = 0 s when the elevator door closed on the second floor and ends at t = 20 s when the door opened on a different floor. Assume that the positive directions for displacement, velocity, and acceleration are upward. Determine… the maximum speed of the elevator the duration of the brief jerk experienced by the elevator centered on 17.5 s Sketch the corresponding graphs of… velocity-time position-time Determine… the most likely floor on which the elevator stopped
If there are two cannons, both completely identical and were shot at same speed and angle. One is shot directly forward, the other one directly upward. If Cannon 2 reaches a max. height from the ground that is eleven-fourths of that of Cannon 1, what will be the time of flight of Cannon 2 in terms of the time of flight of the first cannon? 7/4 tcannon1 15/4 tcannon1 15/8 tcannon1 7/2 tcannon1
A shaft starts from rest and uniformly accelerated at 0.7rev/s2 for 40 seconds, It is then made to stop in next 40 seconds Calculate (i)maximum angular velocity; (ii) total angular displacement. 1.The maximum angular velocity in (rad/s) is 2.The total angular displacement in (rad), θ=
1. A surge is moving at 9 f t/s into a basin of depth 1.4 f t where the speed is zero. Find the water depth behind the surge and the drift velocity behind the surge (that is, the velocity downstream of the surge in a stationary frame of reference). 2. A river of depth 2 m flows downstream at 1 m/s. A surge of depth H moves up the river at 5 m/s relative to a stationary observer on the bank of the river. Find H.
1.a Determine the Velocity of Cable at Point C. Note: Block E is moving downward with a velocity of 4m/s. 1.b Determine the Velocity of block W. Note: Block E is moving downward with a velocity of 4m/s. 1.c Determine the Relative Velocity of Point C with respect to Block E. Note: Block E is moving downward with a velocity of 4m/s. 1.d Determine the Relative Velocity of Block W with respect to Block E. Note: Block E is moving downward with a velocity of 4m/s. 2.a Determine the acceleration of rope at Point A and block B. Note: The block b is lifted 4 inches & velocity at 2ft/s. 2.b Determine the acceleration of block B. Note: The block b is lifted 4 inches & velocity at 2ft/s. 2.c After 0.5 seconds. Determine the velocity of the handle/cable A. Note: The block b is lifted 4 inches & velocity at 2ft/s. 2.d After 0.5 seconds. Determine the change in position of the handle/cable A. Note: The block b is lifted 4 inches & velocity at 2ft/s.
Consider two autonomous vehicles driving in two adjacent lanes as shown in the figure. One is at the rear part of the other at a blind angle. Both cars are driving at 65 miles/hour. If the front car starts to change lane as shown in the figure, a) How far a car can travel in one second with the mentioned speed?b) How much time the V2V communications can have before the two cars collide? c) If the GPS position has an error of one meter, what would be the error margin (minimum, maximum of the time duration before collision) of the result obtained in Part a), d) Provide your suggestions how to improve the positioning accuracy of GPS?e) In your view, what type of sensors could be integrated with GPS to avoid collision?