3) If the radial force is 6001b and the axial force is 2001b at the bearing location, what bearing would you use to achieve 96% reliability, for the shaft rotating 1600RPM, assuming it is in the category of Machines for short or intermittent operation where service interuption is of minor importance?

3) If the radial force is 6001b and the axial force is 2001b at the bearing location, what bearing would you use to achieve 96% reliability, for the shaft rotating 1600RPM, assuming it is in the category of Machines for short or intermittent operation where service interuption is of minor importance?

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

What power can be transmitted by a solid shaft with torque 120 Nm and at frequency of 14 Hz?
A soft start electrical motor that delivers 21,43 KW at 1440 rpm must be connected to a stone crusher (hammer mill type) via a wedge belt drive. The crusher must operate 24 hours per day at a recommended shaft speed of 503,5 rpm,while the centre line distance must not exceed 1000 mm. The crusher shaft is 50 mm in diameter. 1.State the product design specification considering the functionality as a design factor. 2.Use the Fenner catalogue to specify the type and number of wedge belts required for the drive 3.Draw and label all critical parts of the belt drive according to the information provided above
n Mukwano Industries, a shaft assembly shown in Fig. 2 is driven by a flat belt at location A and drives a flat belt at location B. The drive belt pulley diameter is 300 mm; the driven belt pulley diameter is 500 mm. The distance between sheaves is 800 mm, and the distance from each sheave to the nearest bearing is 200 mm. The belts are horizontal and load the shaft in opposite directions. Determine the size of the shaft using Distortion Energy Theory (DET) and the types of steel that should be used. Use a safety factor of 10. Also, provide a free-body diagram as well as moment and torque diagrams
A V-belt drive is required from a 10kW, motor to drive an output pulley of 240mm diameter at 500pm with a reduction of 4:1. It is a light-duty machine that runs 6 hours each day. Using data given in the table and chart below, what would be a suitable V-belt and motor pulley diameter for a single belt installation?
A bilge pump requires 380 N.m torque at about 320 rpm. It is driven by an 1160 rpm motor by means of a roller chain. The nature of service calls for a service factor of 1.5. If the total efficiency of transmission is 95 percent, what is : The size of the motor? Number of sprocket teeth? The pitch and number of strands of the chain required?
The problem is stated below. However, change the position of torque to point C from point D. What is the effect of variation of torque placement in shaft CB?
The figure shows spur gear wheels consisting of two stages with an electric motor used to drive a rope drum. Engine rpm nm = 970 rpm ; desired speed of drum nT = 50 rpm ;since the drum diameter is DT = 40 cm and the load from the rope is Qh = 4000 N: ⦁ (İt) how much is the total cycle rate? ⦁ z4 find the number of teeth of the drum gear, How much is the drum speed realized in this case? ⦁ find the rotation moment on the drum shaft ⦁ since the collection efficiency of the mechanism is nt = 0.82 How much “ Nm " motor power should be
You are asked to design a four cylinder four-stroke spark ignition engine for a passenger car, which is required to provide a maximum brake torque of (2.60x10^2) Nm at the rated speed of (7.000x10^3) rpm. To simply the design, the bore (B)/stroke (L) ratio is assumed to be unit, i.e. B=L. Given that the bmep of the engine is assumed to be (7.000x10^2) KPa, find its mean piston speed. The answer should be in the unit of m/s with 3 significant figures. Note: Your answer is assumed to be reduced to the highest power possible. Your Answer: Question 7 options: x10 Answer
Illustrate what happens when a torque is applied to a circular shaft?
An electric motor drives a punch press with a flywheel and is running at 1200 rpm. The torque of the punch press is as follows: a. 0-(10000+10) at first 45deg b. goes to zero for next 45deg c. 0-(6000+10) at next 45deg d. goes to zero for the remainder of the cycle. Employing a Cf of 0.2, a solid steel disc with density of 0.283 lb/in^3, and a thickness of 2 in, determine the flywheel diameter in meters.
Provide very clear and complete solution and diagam. SITUATIONAL PROBLEM: Two shafts are connected by spur gears. The pitch radii of the gears A and B are 200 mm and 860 mm respectively. If shaft A makes 350rpm and is subjected to twisting moment of 250 N-m. Pressure angle is 14.5 degree. What is: a.) Rpm of gear B b.) Torque in shaft B (in Newton meter). c.) Separation load of two gears (in newtons). d.) Total load on gears (in newtons).
Why is it important that the applied torques must not cause yielding of thematerial?