A square thread power screw without a collar is designed to require a torque TR = 16.15 Nm forraising the load while a torque TL = - 0.5 Nm is required to lower the load. Which of the statements is true?%3DThe design can be self-locking if a collar is added with T > 0.5 NmThe system is self-locking even without collar frictionO The design cab be self-locking if a collar is added with Tc = 0.5 NmThe design cannot be modified to be made self-locking

Given Data→TL=-0.5 NmTR=16.15 Nm

A square thread power screw without a collar is designed to require a torque TR = 16.15 Nm for raising the load while a torque TL = - 0.5 Nm is required to lower the load. Which of the statements is true? O The design can be self-locking if a collar is added with Tc > 0.5 Nm O The system is self-locking even without collar friction O The design cab be self-locking if a collar is added with Tc = 0.5 Nm O The design cannot be modified to be made self-locking

A square thread power screw without a collar is designed to require a torque TR = 16.15 Nm for raising the load while a torque TL = - 0.5 Nm is required to lower the load. Which of the statements is true? O The design can be self-locking if a collar is added with Tc > 0.5 Nm O The system is self-locking even without collar friction O The design cab be self-locking if a collar is added with Tc = 0.5 Nm O The design cannot be modified to be made self-locking

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

1. A jack having square threads of 50 mm nominal diameter and 10 mm pitch is supporting a load of 89 kN. A double thread is used and the coefficient of friction maybe as low as 0.10 or as high as 0.15.a. Will this screw always self-locking?b. What is the highest torque necessary to raise the load?
Design of the Screw Jack. Lifting load – W, kN is 70. Hight of lifting– H, mm is 500 Types of threads is Square Material of nut is Cast iron
A double square thread power screw is to raise a load of 70 kN. The screw has a mean diameter of 33.375 mm and a pitch of 6 mm. The coefficient of thread friction and collar friction are 0.13 and 0.10, respectively. The collar mean diameter is 90 mm and the screw turns at 90 rpm. Which of the following is the torque required to raise the load without friction effect? Group of answer choices 66845 N-mm 133690 N-mm 236078 N-mm 334840 N-mm
4) An electric motor purchased by your employer surprisingly arrived without a keyway in the shaft. The motor has power rating of 7.5kW & 1,800rpm & has a shaft of 17mm. It will be used to drive a centrifugal pump using cast iron sheave. Design the square key to be used in the assembly based on maximum bearing & shearing stresses of 580MPa & 370MPa, respectively, and factor of safety of 5.
The chain drive is mounted in the center for the system shown in figure.It can transmit 15 hp at a speed of 400 rpm and the sprocket has a pitch diameter of 6 inches. The shaft is made of ASTM-A 709 Grade 50 steel. A factor of safety of 2.5 is required. Is the design acceptable? Hint: You need to calculate torsion and bending stresses during solution.
A double square thread power screw is to raise a load of 70 kN. The screw has a mean diameter of 33.375 mm and a pitch of 6 mm. The coefficient of thread friction and collar friction are 0.13 and 0.10, respectively. The collar mean diameter is 90 mm and the screw turns at 90 rpm. Which of the following is the torque required to overcome the collar friction? Group of answer choices 630000 N mm 315000 N mm 819000 N mm 409500 N mm
A cap screw, ¾ in.-10-UNC-2, with a hexagonal head that is 9/16 in. thick, carries a tensile load of 3000 lb. If the material is AISI 1015, cold drawn, find the factor of safety based on ultimate strengths of a. the threaded shank, b. the head against being sheared off, and c. the bearing surface under the head. d. Is there any need to consider the strength of standard cap-screw heads in design?
Don't Copy any wrong solution, Solve it fast within 20-30minutes. 1) A double threaded power screw is to raise a load of 70 kN. The screw has a pitch of 6 mm and turns at 60 rpm. Calculate the power output. a. 490 W b. 840 W c. 420 W d. 980 W
The shaft material is AISI 1040CD steel. The reliability of the design is 90%. The r/d for the shoulder is 0.02. If the design is not feasible, give reasons and suggest modifications. You do not have to consider any other failure criterion. You may assume that the torque is steady and the bending moment is fully reversed.
Design and draw a protective type of cast iron flange coupling for a steel shaft transmitting ‘P is 17kW at ‘N is 350 r.p.m. and having an allowable shear stress of 40 MPa. The working stress in the bolts should not exceed 30 MPa. Assume that the same material is used for shaft and key and that the crushing stress is twice the value of its shear stress. The maximum torque is 25% greater than the full load torque. The shear stress for cast iron is 14 MPa.
Question No.16: A double threaded power screw with ISO metric trapezoidal threads with 15° semi-angle of thread is used to raise a load of 300 kN. The nominal diameter is 100 mm and pitch is 12 mm. the coefficient of friction at screw threads is 0.15. Neglecting collar friction, calculate; (i) torque required to raise the load, (ii) torque required to lower the load and (iii) efficiency of the screw.
(7) The cylinder head of a 10”x18” refrigerant compressor is attached by 10 stud bolts made of SAE grade 5. The maximum cylinder pressure is 350psi. (a) What size of bolt is to be used? (b) What approximate tightening torque should be applied to induce a tightening stress of 0.9 time of the proof stress?