Urgent 3 kN1.5 m7 kN1.5 mBDU 11 kNmALE- 2 m→2.7 m→-4 m→3.5 m-Draw the shear force-bending moment diagram of the beam shown above.

There is a hinge at D. A hinge can only transfer shear force and axial force but not BM, therefore…

Answered: 3 KN1.5 m 6 kN 7 KN1.5 m U 11 kNm A D E…

3 KN1.5 m 6 kN 7 KN1.5 m U 11 kNm A D E - 2 m→-2.7 m–→- 4 m→ -3.5 m- Draw the shear force-bending moment diagram of the beam shown above.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: In the beam shown, take W1 = 9 kN/m, M1 = 25 kN-m, and P1 = 22 kN. a) Determine the reaction at "C"…

A: Given data W1 = 9 KN/m P1 = 22 KN M1 = 25 KNm

Q: 4) Write the equilibrium equations 5) Solve for the unknown exterior reactions. 3 m -3m- B F 60 kN…

Q: w = wo + kx? 7.2 kN 6.0 kN/m 2.3 kN/m 0.7 m A B 0.9 m 1.5 m 0.5 m 0.9 m

A: By using moment equations, force equilibrium equations along the horizontal and vertical reactions,…

Q: Which of the following corresponds to the vertical reaction at the roller support? E 20 k 12 ft 12…

Q: For h-i problems, (a) determine the support reactions, (b) sketch the shear force diagram (c) sketch…

Q: %3D If the intensity of the distributed load acting on the beam is w = 3KN/m, determine the…

Q: 2. Given that the mass of the engine is 350 kg, find a) Support reactions at A and D. b) The forces…

A: Given , Mass of engine w=350 kg g=9.81 m/s2

Q: Determine the vertical reaction at B for the beam shown below. 222.5 kN 22 kN/m 135.7 AN - m 30 -2 m…

A: To Determine Vertical Reaction at B, VB

Q: 10 kN 15 kN/m 15 kN/m 2.0 4.0 4.0

Q: Given the beam loaded as shown below, determine: (a.)Determine the reaction of (b.)Shear diagram the…

A: Given: Beam with internal support Compute reactions and draw shear and moment diagram

Q: Determine the internal bending moment at point C. * 12 kN.m 6 kN O 24.0 kN-m O -24.0 kN-m O 9.33…

Q: The cantilever beam carries a combination of a uniformly distributed load and a trapezoidal loading…

Q: Determine the maximum negative shear at E (in kN) due to dead load of 3 kN/m and the two…

Q: Determine the shear force at point A for the beam shown below. 90 kN 100 kN m 80 kN m 75 kN 6 m- -2…

Q: 25. What is the reaction at 20 kNím 60AN support B? 120 AN - m 26. What is the maximum shear force?…

Q: From the figure below, determine the fallowing a) reaction at A and B. b.) Shear and Moment at C and…

Q: q (kN/m) B A + -6 m- -3 m- a) Determine the support reactions. b) Calculate for the maximum bending…

A: Given data q = 18 KN/m P = 81 KN

Q: 150 kN 40 kN/m Determine the vertical reaction at support B of the given frame. 8 m 20 kN/m 6 m 6 m…

Q: Determine the shear force Vin the beam at a point located 0.90 m to the right of point B. The ground…

Q: 2 kN Problem 1 0.3 m Calculate the force in member BD and the reaction at the roller support for the…

Q: The cantilever beam carries a combination of a uniformly distributed load and a trapezoidal loading…

Q: P kN B w W kN/m 12 m A 5 m - 5 m Draw the shear, moment and axial force diagrams of the given frame.…

Q: F1-1. Determine the resultant internal normal force, shear force, and bending moment at point C in…

A: Given,

Q: Determine the vertical reaction at B for the beam shown below. 222.5 kN 22 kN/m 135.7 kN - m 30 tamt…

A: Appreciate if there is detailed work with explanation and finds you helpful for ease of…

Q: A. Find the reaction at support B (RB) B. Find the reaction at support B (MB) C. Draw the shear…

A: Draw FBD:

Q: Determine the reactions on the beam. 20 kN 20 kN 20 kN 20 kN B 50° F3m+3 m–3 m–3 m- m-3 m- 8 kN

A: This question is related to the structure analysis. In this question we calculate the reaction at…

Q: Situation 7. The L-shaped bar is supported by a bearing at A and rests on a smooth horizontal…

A: Draw the free body diagram.

Q: Determine the maximum negative shear at E (in kN) due to dead load of 3 kN/m and the two…

Q: Calculate the reaction supports at point A and D (i.e., Ay and Dy) for the beam shown in figure,…

A: Solution:-

Q: 0.1: Figure Q.1. shows an overhanging beam AD supported at A and C and, uniformly distributed loads…

Q: Q4: Calculate Reactions at A and B. Draw Shear Force Diagram. Find location of Zero Shear force.…

Q: Question 2 P= 56 KN W= 25 KN /m 3 m 2 m Determine the reactions at the supports A, and B. Use the…

A: Solution: Using Super-Position Principle…

Q: 1. Given the beam shown. 100 kN 40 kN/m 30 kN/m B J100 kN - 3 m - -3 m - 6 m a.) Determine the…

A: To find the support reactions -

Q: a. Determine the Maximum Shear b. Determine the Maximum Moment 10 k/ft 10k 5 k/ft 5 k/ft 5 ft 10 ft…

Q: 5 kN/m Example For the beam and loading shown, determine the magnitude of the force F for which the…

Q: Determine the vertical reaction at B for the beam shown below. 222.5 kN 22 ΚN/m 135.7 kN m 30 tomt…

Q: w2 kN/m C B W1KN/m 10 m A 10 m 5 m Draw the shear, moment and axial force diagrams of the given…

Q: 3 12 kN/m C A 15 kN/m 10 m D Figure P4.7 5 5 m 6 m

Q: Situation 7. The L-shaped bar is supported by a bearing at A and rests on a smooth horizontal…

A: Let Ra and Rb be the reactions at supports A and b respectively, - Since the vertical force is…

Q: Determine the vertical component of the reaction By at the pin support B 30 kN 50 kN to B D A 1 m 3…

Q: The steel beam is loaded as shown in the figure. Draw the shear and moment diagrams. 3 KN 6 KN 5KW/m…

Q: Calculate the vertical reaction at B. Let P = 10 kips and W = 4 kips/ft. Assume support at B as…

Q: The cantilever beam carries a combination of a uniformly distributed load and a trapezoidal loading…

Q: w kN m 5m- 3m 5m-

A: Given:- RA + RB = 3 + 22x5 RA + RB = 113 Taking Moment about point A Rb x 8 = 3 x 5 + 22x5x10.5…

Q: 26-3 KN 46.8 KNIM A 4.8 m 4n

Q: The dead-weight loading along the centerline of the airplane wing is shown. If the wing is fixed to…

Q: Due to a certain horizontal force frame shown below, the moments are Follows MAB = 5 kN.m (Anti…

A: To find force P

Q: The steel beam is loaded as shown in the figure. Draw the shear and moment diagrams. 10 KN 8KN 4…

Q: Show your step-by-step solution.

Q: . Solve for the following internal forces occurring on the beam loaded as shown below. a. Moment at…

Concept explainers

Team Management

To complete a specific task or to accomplish organizational goals along with increasing work productivity, individuals need to come together and think along a common path and direction. There are certain tasks in an organization that cannot be done alone and the involvement of more individuals is essential. These groups of individuals who work together for a common goal compose a team and the individual members involved are known as team members.

Question

Urgent

3 kN1.5 m
7 kN1.5 m
B
D
U 11 kNm
A
LE
- 2 m→2.7 m→-4 m→3.5 m-
Draw the shear force-bending moment diagram of the beam shown above.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

SFD BMD

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

Determine the shear force V in the beam at the point located 2.50 m to the left of point C. The ground reactions and shear-force diagram are shown. -30.6 kN -48.2 kN -57.2 kN -38.2 kN -40.9 kN
Vertical Forces P & F in the figure produces a resultant of 500KN and a counter clockwise couple C of 250 KN-m. Find the magnitude of force P. a.) 1187.5 KN b.) -1687.5 KN c.) -1187.5 KN d.) None of the Above e.) 1687.5 KN
look for: a. Reactions b. Shear and Moment Diagramc. Maximum Momentd. Equations w=022 Kn/m
1. what is the maximum moment in the beam? answer in KN-m 2. what is the maximum shear in the beam? what is the highest shear force at 6m? (kN) 3. what is the shear force at the free end of the beam? 4. what is the highest shear force at 6m? (kN 1Decimal point)
Determine the member end moments and reactions for the continuous beam shown in the Figure (a) due to the uniformly distributed load and due to the support settlements of 10 mm at A, 50 mm at B, 20 mm at C, and 40 mm at D. Use the three-moment equation. Ans. MB =115.2 kN.m , MC = 451.2 kN.m, Ay = 138.5 kN, By = 277.9 kN, Cy = 378.7 kN, Dy = 104.9 kN
GIVEN: L1 = 4.5 m W1 = 10 kN/m L2 = 1.2 m W2 = 12 kN/m L3 = 0.5 m L4 = 12 m L5 = 1.5 m A. What is the maximum shear in Beam D-E-B? B. What is the maximum moment in Beam A-B-C?
M = 8 kip*ft , P = 8 kip , w = 1.3 kip/ft Determine the internal normal force, internal shear force, and internal moment passing through point E.
Considering the diagram as a whole body, the downward forces and the upward reactions are equal. They are? a. 160 kN = 160 kN b. 125 kN = 125 kN c. 145 kN = 145 kN d. None of the above The horizontal reaction at A is? a. 15.02 going to the right b. 15.02 going to the left c. 19.02 going to the right d. 19.02 going to the left
Draw the bending moment diagram of the system under the influence of external loads below. Calculate the vertical displacement value at the intersection of the horizontal beam and vertical column member? (EI= 50000kNm2)
Dead Load= 20 kN/mLive Load= 30 kN/mUnit weight of concrete= 23.56 kN/cu.mf'c= 27.6 MPafy= 414 MPaCompute the shear and moment diagram.
Determine the reaction forces R1 and R2 and show the shear and bending moment diagram. Data: Point load (left-most) = 90.126 N RL1 (80mm to 160mm) = 65 N RL2 (160mm to 180mm) = 130 N RL3 (180mm to 260mm) = 65 N
If P = 20.3 and M = 6.83, Determine the Shear Force at point B of the Beam shown.