The steel beam is loaded as shown in the figure. Draw the shear and moment diagrams. 3 KN 6 KN 5KW/m 3 KN/m 3m IR2 6m 18m IRI Compute the reaction R, in KN.0 Compute the reaction R, in KN.0 Compute the distance from R, where the shear is zero in mm.0 Indicate the opening of the shear diagram cuve between R, and R.0 Compute the maximum positive moment in the beam in KN.m.0

The steel beam is loaded as shown in the figure. Draw the shear and moment diagrams. 3 KN 6 KN 5KW/m 3 KN/m 3m IR2 6m 18m IRI Compute the reaction R, in KN.0 Compute the reaction R, in KN.0 Compute the distance from R, where the shear is zero in mm.0 Indicate the opening of the shear diagram cuve between R, and R.0 Compute the maximum positive moment in the beam in KN.m.0

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter9: Application Of Influence Lines

Section: Chapter Questions

Problem 2P

See similar textbooks

Similar questions

For the beam presented below:a) What is the degree of indeterminacy; b) Determine the moment reactions at the supports and draw the shear and momentdiagrams. (Solve by expressing the internal moment in terms of vertical reactionsat A and B, EI is constant). c) What would the shear diagram look like if a transverse load P was applied right atthe middle of the beam (Make a sketch of the new shear diagram). W (30kN/m) , L (1.9m)
Determine (a) the absolute maximum values of shear and moment in the beam produced by the wheel loads and (b) the maximum value of moment when the middle wheel is positioned at the center of the beam in Figure P12.43.
Given the loaded beam below, calculate the reaction and draw the shear and moment diagram. M1= 20kN.m q1= 15 kN/m P1= 8kN
5-Draw the shear force and bending moment diagram for the loaded simply supported beam as shown below. Also mark all salient point of shear force and bending moment values in the diagram with proper units. locate the point where the shear force changes its sign from "+" to "-" and the value of maximum bending moment. where F1=280N, F2=290N, w=14N/m, a=2 m, b=2 m, c=2 m, d=5 m, e=3 m The reaction at the support "A" in N is = ________________ The reaction at the support "B" in N is = ________________ The shear force at the point "A" in N is = _________ The shear force at the point "C" in N is = _________ The shear force at the point "D" in N is = _________ The shear force at the point "E" in N is = _________ The shear force at the point "P" in N is = _________ The shear force at the point "B" in N is = _________ The value bending moment with respect to "B" in Nm is = __________ The value bending moment with respect to "P" in Nm is = __________…
1.) What is the vertical reaction at A and B?2.) What is the horizontal and moment reaction B3.) What is the maximum positive moment in the beam?(kN-m)4.) What is the location of the maximum positive moment from point A? (m) 5.) What is the shear at a point between A and C?6.) What is the moment at a point under the concentrated load?
C0nsider the frame bel0w where f0rce A = 55 N acts 0n p0int Q, f0rce B = 34 N acts on p0int P, and force C = 42 N acts on p0int M. Replace the system of f0rces acting on the frame with two f0rces, one acting on p0int O and the other acting vertically at point P. Calculate the magnitude and direction of the vertical f0rce acting on p0int P, FP, and the force acting on p0int O, FO.
Draw the shear and moment diagrams for the beam. Find the reaction at support A and the reaction at support C. Find the shear at point B. Find the moment at point B.W= 54 kN/m
Given : M1 = 4000 N/m M2 = 9000 N/m P = 3600 N (downward) w1= 800 N/m (downward) w2 = 600 N/m (downward) a = 4 m b = c = d = 5 m Determine the following:a. The maximum positive shear (in N).b. The maximum negative shear (in N).c. The maximum positive moment (in N-m).d. The maximum negative moment (in N-m).e. The location of maximum shear from the left end of the beam (in m).f. The location of the maximum moment from the left end of the beam (in m). Kindly Draw the detailed Shear and Moment Diagram. Compute for all of the necessary elements, Include the proper units, use the proper formula and round-off all the answers and final answers to 2 decimal places.
Compute the reactions and draw the shear andmoment curves for the beam in Figure P9.20. Given: EI isconstant for the beam. E = 200 GPa, I = 40 × 106 mm4
Consider the object shown. Suppose that P = 390 N . Follow the sign convention. A) Determine the internal normal force at point C. NC = ? B) Determine the internal shear force at point C. VC = ? C) Determine the internal moment at point C. MC = ?
Draw the shear and moment diagrams for the beam. Find the reaction at support A and the reaction at support B. Find the maximum positive moment and the maximum negative moment in the beam. Find the shear between point A and B, and find the moment between point A and B. W = 54 kN/m P = 22 kN/m
Solve Prob. 7.53 when 0=60°.(Reference to Problem 7.53):Two small channel sections DF and EH have been welded to the uniform beam AB of weight W = 3 kN to form the rigid structural member shown. This member is being lifted by two cables attached at D and E . Knowing that 0= 30° and neglecting the weight of the channel sections, (a) draw the shear and bending-moment diagrams for beam AB, (b) determine the maximum absolute values of the shear and bending moment in the beam.