3-phase, 380V, 50HZ, 4-pole, Y-connected asynchronous motor's rated speed is 1380 rpm. The two ends of the stator terminals The resistance value between is measured as 150. It is known that the value of friction and wind losses is 33W. The values taken from idle running and locked rotor tests are given below. Accordingly, one phase equivalent of the motorDraw the equivalent circuit by finding the circuit parameters. idle test locked rotor test input power 220W 370W line current 1.82A 3.11A Line voltage 97V

3-phase, 380V, 50HZ, 4-pole, Y-connected asynchronous motor's rated speed is 1380 rpm. The two ends of the stator terminals The resistance value between is measured as 150. It is known that the value of friction and wind losses is 33W. The values taken from idle running and locked rotor tests are given below. Accordingly, one phase equivalent of the motorDraw the equivalent circuit by finding the circuit parameters. idle test locked rotor test input power 220W 370W line current 1.82A 3.11A Line voltage 97V

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

A three-phase induction motor, operating at rated voltage and frequency, has a startingtorque of 1.35 times and a maximum torque of 2.2 times, both with respect to its rated-loadtorque. Ignoring the effects of the stator resistance and rotational losses and assumingconstant rotor resistance, determine the slip rated load, and the rotor current at starting (as a percentage of the rotor current at rated load). The slip at maximum torque is 0.343 if that helps.
A three-phase 60 Hz induction motor connected to a three-phase bus at rated voltage isoperating at a low slip condition (i.e s < 20%) resulting in a steady state speed of 1090 rpm.(a) How many poles does the motor have?(b) What is the percentage slip at the operating speed?(c) What is the corresponding frequency, (fr) of the currents and voltages induced in therotor winding?
a. A three-phase, 220-V, 60-Hz induction motor runsat 1,140 r/min. Determine the number of poles (forminimum slip), the slip, and the frequency of therotor currents.b. To reduce the starting current, a three-phasesquirrel cage induction motor is started byreducing the line voltage to Vs/2. By what factorare the starting torque and the starting currentreduced?
The rotor resistance and reactance per phase of a 4-pole, 50-Hz, 3-phase induction motor are 0.025 ohm and 0.12 ohm respectively. Make simplifying assumptions, state them and : (i) find speed at maximum torque (ii) find value of additional rotor resistance per phase required to give three-fourth of maximum torque at starting. Draw the equivalent circuit of a single-phase induction motor.
The full load slip of a 4-pole, 60Hz, 440V (line-to-line) three phase induction motor is 0.05. (i). What is the speed of the rotating stating? What is the frequency (in Hz) of the rotor current? (ii). When the output power of the motor is 90 hp at a speed of 1732 rmp, rotational losses (which include frictional and core losses) are 10,100W, while copper losses for both the rotor and stator total 3700W. Determine the motor efficiency and line current, assuming the motor has a 0.8pf lagging under the conditions.
A three-phase, star connected, 50Hz, 4-pole, 380V, 15HP asynchronous motor rotating at 1404 rpm below has one phase equivalent circuit parameters. The friction and wind losses of this motor are 250W. A phase equivalent circuit is simplified by taking the magnetic circuit in front of the stator circuit. Accordingly, find the slip where the maximum torque occurs, the maximum torque, the slip where the maximum power occurs, the maximum power and the development current. (Rs = 0.15Ω, R′r = 0.18Ω, Xs = 0.31Ω, X′r = 0.31Ω, Vs = 220V)
A 3-phase, 6-pole induction motor is rated 400Hz, 150V, 10hp, 3% slip at rated power output. The windage and friction loss is 200W at rated speed. With the motor operating at rated voltage, frequency, slip, and power output, determine the output torque.
A 3300-V, 50-Hz, 3-phase, 4-pole, star-connected induction motor has identical primary and referred secondary impedances of value 3 + j9 ohm per phase. The turns-ratio per phase is 3/I (stator/rotor), and the rotor winding is connected in delta and brought out to slip rings. Calculate: the full-load torque at rated slip of 5%; the maximum torque at normal voltage and frequency; the supply voltage reduction which can be withstood without the motor stalling; the maximum torque if the supply voltage and frequency both fall to half normal value; the increase in rotor-circuit resistance which, at normal voltage and frequency, will permit maximum torque to be developed at starting. Express this: as a fraction of normal R2and as (3) ohmic values to be placed in series with each of the slip-ring terminals and star connected.
a 220v dc shunt motor takes 5a and 40a at no load and full load respectively it has an armature resistance of 0.2 ohm and field resistance of 110 ohm respectively. iron,friction and windages losses are negligible.then using among parameters find following. the ratio of emf at no load to full load
For 3-phase,50 Hz, SCIM, rotor leakage reactance at standstill is twice of it's resistance.The frequency of the supply at which maximum torque is obtained at starting is ?
A three phase, 50Hz, 6-pole squirrel cage induction motor runs at 960-rpm on full load. The stand still rotor resistance and reactance per phase are 0.01 ohm and 0.05 ohm respectively. Express the maximum torque developed in terms of full load toque. Find the slip at which the maximum torque occurs.
Design and develop equivalent circuit model of a single phase Induction motor with th consideration of core losses present with the parameter consideration of stator resistance R1 and reactance X1 and two rotor parameters which includes r2,x2 and magnetising reactance xm. (Illustration is required) Draw by hand please