i need the answer quickly 3. A 6.85 in pump, running at 3500 r/min, has the following measured performance for waterat 20°C ( pw =1.94 slug/ft'):Q. gal/min50100 150200250300350400450H, ft201200198194189181169156139n, %295064727780817974(a) Estimate the horsepower at BEP. If this pump is rescaled in water to provide 20 bhp at3000 r/min, determine the appropriate (b) impeller diameter, (c) flow rate, and (d)efficiency for this new condition. Ans. (a) P = 18.5 bhp, (b) D= 7.64 in, (c) Q' =415 gpm.

(a) BEP stands for Best Effeciency Point. from the given table data the maximum efficiency is 0.81…

3. A 6.85 in pump, running at 3500 r/min, has the following measured performance for water at 20°C ( pw =1.94 slug/ft): Q. gal/min 50 | 100 | 150 200 250 300 350 450 400 H, ft 201 200 198 194 189 181 169 156 139 7, % 29 50 64 72 77 80 81 79 74 (a) Estimate the horsepower at BEP. If this pump is rescaled in water to provide 20 bhp at 3000 r/min, determine the appropriate (b) impeller diameter, (c) flow rate, and (d) efficiency for this new condition. Ans. (a) P= 18.5 bhp, (b) D= 7.64 in, (c) Q' =415 gpm. %3D

3. A 6.85 in pump, running at 3500 r/min, has the following measured performance for water at 20°C ( pw =1.94 slug/ft): Q. gal/min 50 | 100 | 150 200 250 300 350 450 400 H, ft 201 200 198 194 189 181 169 156 139 7, % 29 50 64 72 77 80 81 79 74 (a) Estimate the horsepower at BEP. If this pump is rescaled in water to provide 20 bhp at 3000 r/min, determine the appropriate (b) impeller diameter, (c) flow rate, and (d) efficiency for this new condition. Ans. (a) P= 18.5 bhp, (b) D= 7.64 in, (c) Q' =415 gpm. %3D

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Provide clear and complete solution as well as diagram. The initial condition of air in an air compressor is 97 kPa and 27 oC and discharges air at 350 kPa. The bore and stroke are 250 mm and 280 mm, respectively with percent clearance of 6 percent running at 310 rpm. Find the volume of air at suction in m3/hr. A. 232.61 C. 156.34B. 289.16 D. 135.23
A certain centrifugal pump was tested and its performance curves can be approximated as follows: H = 340 - 1.2(Q2), in feet BP = (0.0521Q3) + (1.25Q2) + (11.042Q) + 134.5, in horsepower where Q is in ft3/s. If two of this pump is connected in series to deliver water to a system whose head requirement is 615 ft, what will be the operating discharge rate in ft3/s of either pumps? Assuming the head is equally divided between the two pumps, what is the efficiency of either pumps (in %)? Take the specific weight of water to be 62.4 lbf/ft3.
7.) The pressure drop associated with hydraulic fluid with a Sg of 0.93 flowing across a 1-in. I.D. sharp edge orifice is 20 lbf/in2 . If the discharge coefficient is 0.60, what flow rate in gal/min could be expected through the orifice?
A piston PDP has a 5-in diameter and a 2-in stroke andoperates at 750 r/min with 92 percent volumetric effi ciency.(a) What is its delivery, in gal/min? (b) If the pump deliversSAE 10W oil at 20°C against a head of 50 ft, what horsepoweris required when the overall effi ciency is 84 percent?
A turbine of the Francis type operates with a head of 200 m and flow rate of 3 m3/s.The peak efficiency occurs at a head coefficient CH of 9, a flow coefficient CQ of 0.3, and apower coefficient CP of 2.5 (as defined in Section 12.7). Estimate the size of the machine,the maximum power produced, and the speed.
A certain centrifugal pump was tested and its performance curves can be approximated as follows: H = 340 - 1.2(Q2), in feet BP = (0.0521Q3) + (1.25Q2) + (11.042Q) + 134.5, in horsepower where Q is in ft3/s. If two of this pump is connected in series to deliver water to a system whose head requirement is 615 ft, what will be the operating discharge rate in ft3/s of either pumps?
Acentrifugal pump has di = 24 cm, d2 = 36 cm, by = 12 cm, bz =7.5 cm, B1 = 22° and B2 = 38° and rotates at 1170 r/min. If the fluid is gasoline at 20°C and the flow enters the blades radially, estimate the theoretical (a) flow rate (b) horsepower, and (c) head. For gasoline, take p=680 kg/m3. R Gy Juald e
A propeller turbine develops 12,000hp, and rotates at 145rpm under a head of 20m. The outer and hub diameters are 4m and 1.75m, respectively. Calculate the inlet and outlet blade angles measured at mean radius if overall and hydraulic efficiencies are 85% and 93%, respectively. Show schematic diagram and provide solutions.
The original design of a hydraulic turbine has data as follows: flow rate of 1 cumex, effective head of 50 m, and runner diameter of 1.5 m. If the same turbine design is to be used in another application where the available flow is 2.5 cumex and effective head is 75 m, what would be the runner diameter (in meters) for this new application?
Fluid Mechanics. plz, solve all the parts from a , b and c Reg.no : 5395 Pb # 6: At its optimum point of operation, a given centrifugal pump with an impeller diameter of 500 mm delivers a 4 m3/s of water against a head of (Reg.No/100) m when rotating at 1500 rpm. (a) If its efficiency is 82%, what is the brake power of the drive shaft? (b) If a homologous pump with a diameter of 800 mm is rotating at 1200 rpm, what would be the discharge, head, and shaft power. Assume both operate at the same efficiency. (c) Compute the specific speed of both pumps. What type of pumps are these?
It is desired to construct a hydraulic turbine for a hydraulic power plant to operate under the following conditions: discharge Q = 3.5 m3/s of water, the available net head = 290 meters, the hydraulic efficiency = 0.8, the rotating speed = 300 rpm. A Pelton wheel impulse turbine was selected with the following specifications: the bucket angle b2 = 160°, the coefficient of velocity for the nozzle is 0.98 and assume the friction coefficient k = 0.2. Determine the following:Jet Diameter to Wheel diameter ratio, dj/Dw. The Specific Speed in M.K.S., Ns.The computed head coefficient ϕ.The brake horsepower. The required number of Jets. The Pelton wheel diameter in meters.
Acentrifugal pump has di = 24 cm, dz = 36 cm, b1 = 12 cm, bz =7.5 cm, B1 = 22°, and B2 = 38° and rotates at 1170 r/min. If the fluid is gasoline at 20°C and the flow enters the blades radially, estimate the theoretical (a) flow rate (b) horsepower, and (c) head. For gasoline, take p=680 kg/m3.