3. A composite circular plate was made by welding two semi-circular plates of different densities such that the left part is denser than the right part. Suppose that a performer wishes to balance the plate by resting it on top of a sturdy stick, which of the following shows how should the stick be oriented to balance the composite circular plate? А. C. D. B.

3. A composite circular plate was made by welding two semi-circular plates of different densities such that the left part is denser than the right part. Suppose that a performer wishes to balance the plate by resting it on top of a sturdy stick, which of the following shows how should the stick be oriented to balance the composite circular plate? А. C. D. B.

College Physics

1st Edition

ISBN:9781938168000

Author:Paul Peter Urone, Roger Hinrichs

Publisher:Paul Peter Urone, Roger Hinrichs

Chapter9: Statics And Torque

Section: Chapter Questions

Problem 7PE: Two children of mass 20.0 kg and 30.0 kg sit balanced on a seesaw with the pivot point located at...

See similar textbooks

Similar questions

Unreasonable Results Suppose two children are using a uniform seesaw that is 3.00 m long and has its center of mass over the pivot. The first child has a mass of 30.0 kg and sits 1.40 m from the pivot. (a) Calculate where the second 18.0 kg child must sit to balance the seesaw. (b) What is unreasonable about the result? (c) Which premise is unreasonable, or which premises are inconsistent?
A person balances a meterstick in a horizontal position on the extended index fingers of her right and left hands. She slowly brings the two fingers together. The stick remains balanced, and the two fingers always meet at the 50-cm mark regardless of their original positions. (Try it!) Explain why that occurs.
(a) Give an example in which the net force acting on an object is zero, yet the net torque is nonzero, (b) Give an example in which the net torque acting on an object is zero, yet the net force is nonzero.
What three factors affect the torque created by a force relative to a specific pivot point?
Two forces are acting on an object. Which of the following statements is correct? (a) The object is in equilibrium if the forces are equal in magnitude and opposite in direction. (b) The object is in equilibrium if the net torque on the object is zero. (c) The object is in equilibrium if the forces act at the same point on the object. (d) The object is in equilibrium if the net force and the net torque on the object are both zero. (e) The object cannot be in equilibrium because more than one force acts on it.
The fishing pole in Figure P10.28 makes an angle of 20.0 with the horizontal. What is the torque exerted by the fish about an axis perpendicular to the page and passing through the anglers hand if the fish pulls on the fishing line with a force F = 100 N at an angle 37.0 below the horizontal? The force is applied at a point 2.00 in from the anglers hands.
a) What is the mechanical advantage of a wheelbarrow, such as the one in Figure 9.24, if the center of gravity of the wheelbarrow and its load has a perpendicular lever arm of 5.50 cm, while the hands have a perpendicular lever arm of 1.02 m? (b) What upward force should you exert to support the wheelbarrow and its load if their combined mass is 55.0 kg? (c) What force does the wheel exert on the ground? Figure 9.24 (a) In the case of the wheelbarrow, the output force or load is between the pivot and the input force. The pivot IS the wheel's axle. Here, the output force is greater than the input force. Thus, a wheelbarrow enables you to lift much heavier loads than you could with your body alone. (b) In the case of the shovel, the input force is between the pivot and the load, but the input lever arm is shorter than the output lever arm. The pivot is at the handle held by the right hand. Here, the output force (supporting the shovel's load) is less than the input force (from the hand nearest the load), because the Input is exerted closer to the pivot than is the output
(i) If you are trying to loosen a stubborn screw from a piece of wood with a screwdriver and fail, should you find a screwdriver for which the handle is (a) longer or (b) fatter? (ii) If you are trying to loosen a stubborn bolt from a piece of metal with a wrench and fail, should you find a wrench for which the handle is (a) longer or (b) fatter?
The fishing pole in Figure P8.3 makes an angle of 20.0 with the horizontal. What is the magnitude of the torque exerted by the fish about an axis perpendicular to the page and passing through the anglers hand if the fish pulls on the fishing line with a force F=1.00102N at an angle 37.0 below the horizontal? The force is applied at a point 2.00 m from the anglers hands. Figure P8.3
Answer yes or no 10 (he following questions, (a) Is it possible to calculate the torque acting on a rigid object without specifying an axis of rotation? (b) Is the torque independent of the location of the axis of rotation?
Suppose a horse leans against a wall as in Figure 9.31. Calculate the force exerted on the wall assuming that force is horizontal while using the data in the schematic representation of the situation. Note that the force exerted on the wall is equal in magnitude and opposite in direction to the force exerted on the horse, keeping it in equilibrium. The total mass of the horse and rider is 500 kg. Take the data to be accurate to three digits.
Two window washers. Bob and Joe, are on a 3.00-m-long, 345-N scaffold supported by two cables attached to its ends. Bob weighs 750 N and stands 1.00 m from the left end, as shown in Figure P8.82. Two meters from the left end is the 500-N washing equipment. Joe is 0.500 m from the right end and weighs 1 000 N. Given that the scaffold is in rotational and translational equilibrium, what are the forces on each cable? Figure P8.82