3. A homogeneous bar with a cross-sectional area of 400 mm² is attached to fixed supports as shown in the figure. It is subjected to lateral forces P, = 20 kN and P2 = 50 kN. Determine the normal stress developed in segments AB and BC. Answer: OAB = 80.55 MPa A B P1 P2 0.60 m 1.20 m 0.90 m

3. A homogeneous bar with a cross-sectional area of 400 mm² is attached to fixed supports as shown in the figure. It is subjected to lateral forces P, = 20 kN and P2 = 50 kN. Determine the normal stress developed in segments AB and BC. Answer: OAB = 80.55 MPa A B P1 P2 0.60 m 1.20 m 0.90 m

Principles of Foundation Engineering (MindTap Course List)

8th Edition

ISBN:9781305081550

Author:Braja M. Das

Publisher:Braja M. Das

Chapter6: Vertical Stress Increase In Soil

Section: Chapter Questions

Problem 6.4P: Refer to Figure P6.4. A strip load of q = 900 lb/ft2 is applied over a width B = 36 ft. Determine...

See similar textbooks

Related questions

Q: A 6-m long restrained beam is carrying an ultimate load of 98 kN per meter throughout the span. The…

Q: Dense Sandy Gravel Y. = 21kN/m = 37 Firm Clay Y. - 18KN/m² - 40 kPa Fig. a Fig. b

Q: A steel rod of length = 3m, diameter = 300 mm and modulus of elasticity = 200 GPa is inserted into…

A: step 1-

Q: discharge pipe in which the velocity is 2.40m/sec. At point A in the suction p pressure is - 40kPa.…

A: Given:- diameter =200mm discharge pipe dimater =150mm To find:- Power

Q: A 550mmx800mm column reinforced with 12 pcs of D20mm (3 bars each on outer ends). The column carries…

A: Solution: Given: column = 550mmx800mm 12 pcs of D20mm (3 bars each on outer ends). ultimate load of…

Q: Given a 2-D force system with geometry as shown. Find the magnitude of the equivalent resultant…

A: Express each force as a Cartesian vector. Then make the vector sum of these forces to obtain the…

Q: Exercise 4.2 The plan of a foundation is given in Fig. 1. The uniform pressure on the soil is 40…

A: Solution: Given: Soil pressure = 40 kPa Base = 9 m Since it is a uniform load applied. lets…

Q: 3) For the structure shown below, use the slope-deflection equation method to determine the end…

A: The slope-deflection method relies on the use of the slope-deflection equation, which relate the…

Q: Problem # 3: The steel bars are firmly attached to rigid supports. Initially the temperature is…

A: ASKED: To determine the stress in bars AC and AB. Given, Initial temperature (T1) = 84 oF Final…

Q: A 100 kN block is o horizontal. Find the

Q: A slab panel is carrying a superimposed dead load of 2.70 kPa and superimposed live load of 6.0 kPa…

Q: 2.7 (a) A built-up laced column of overall square cross-section, 300 mm size has been formed by…

A: Using IS coad 800:2007 Assuming the gauge length 55mm Permissible stress on lacing bar 150MPa

Q: A 15 kW pump with 80 % efficiency is discharging oil of specific gravity 0.85 to the overhead tank…

Q: Compute for the Modulus of Elasticity of the Wood if the Clear Span Length is 2300 mm, applied load…

Q: For the truss shown in the figure below, assume that the loads are being transmitted to the bottom…

A: Given :

Q: ty of the Wood if the Clea

Q: A large pipe, called a penstock in a hydraulic work, is 1.5 m in diameter. It is composed of wooden…

Q: -0.3 What's the value of FS against overturning and 3 sliding for the Figure shown. Y = 18.08 kN/m C…

Q: Water is flowing through a 5 in diameter pipe at a velocity of 4 ft/s. If the length o the pipe is…

A: To determine the Reynolds numbar(Re)-

Q: Problem 9-3. Determine the deflection at the end B of the clamped (Fixed at A) A-3 steel strip. The…

A: Given -

Q: Exercise 5 A transition curve is required for a single carriageway road with a design speed of 100…

Q: From the figure, determine the reaction at A and D. 900N/m B 3m 4m 2m

A: Given:

Q: You are standing on the surface of the Sun (wear your sunscreen!). If you want to launch a…

Q: A cylindrical tank in which the hydrostatic pressure applied to it from the liquid column is (450…

A: Pressure at 8 m from the tank base = 400 kgf/m2 Pressure at 5 m from the base of the tank = 200…

Q: What is water cement ratio? Compute the value of water cement ratio in the mix. Answer with 2…

Q: 0.5 in. B 6 in. 6 in.. 0.5 in. 2 in. 0.5 in. 0.5 in. 0.5 in. Prob. 7-61

Q: Refer to the beam shown below. P = 85.50KN 75 P (kN) 60 kN/m kN/m 2m 1m 3m 3m 90 kN.m A B C D E a)…

A: As simply support beam is given and no inclined and horizontal load is acting on beam so, only…

Q: For the beam ABCD subjected to the loading shown in figure below (B intemal hinge) (1) draw the…

Q: A horizontal plate turns an oil jet. If ?1 = 30 m/s, ?2 = 25m/s, and the area of incoming jet ?1 =…

Q: Problem # 2: The composite bar is subjected to a normal force P = 7500 lb as shown in the figure.…

Q: Find maximum principal stress

A: Given data : The value of normal stress in X direction σX=66 MPa The value of normal stress in Y…

Q: 2. Draw the shear-force and bending-moment diagrams for the simply supported beam shown. Determine…

Q: In the propped beam shown, Solve for the following a. wall moment b. maximum deflection note : use…

Q: A short rectangular column 300 mm on one side and 400 mm on the other side. It is reinforced with…

A: f'c= 21 MPa and fy = 415 MPa

Q: A car travels due east at 22 m/s. It makes a turn due south and continues to travel at 22 m/s. What…

A: The values given in the question are as follows: Velocity of car in east(ve→)=22i m/sec Velocity of…

Q: Derive the "bulk density" and "voids" formulas?

Q: The ruling gradient in a hill road is 6% and a horizontal curve is provided for a radius of 75…

A: Given data- Ruling gradient=6%Radius of curve R=75 m

Q: Calculate the maximum permissible speed on curve of high speed B.G. track having the following…

A: Given data: Degree = 2o. Super elevation (E)=8 cm Length of transition curve = 150 m Sanctioned…

Q: Problem # 7: A rectangular steel block is 4 inches long in the x direction, 2 inches long in the y…

Q: The following figure shows a borrow pit in the shape of a grid with all the dimensions and If this…

Q: Use the method of joints to determine the force in each member of the roof truss shown. State…

Q: In the restrained beam shown, solve for the following a. end moments b. max deflection note: use…

Q: Question (2; In Jer to test the öf än airplane wing. over the sur a model is built to a scale of…

A: 1.) The model has to maintain Geometric, Dynamic, and Kinematic similarities in order to have…

Q: Q4: A 7-cm diameter solid aluminum ball balance nicely when submerged in a fluid as shown in figure.…

A: Given: Dal = 7cm, S.Gal = 2.7, SGbr = 8.5

Q: 31 A sample of air analysed at 0°C and 1 atm pressure is reported to contain 0.02 ppm (parts per…

Q: A steel column of ISHB 350 @72.4 kg/m is subjected to a factored axial compressive load of 2000 kN.…

A: Given data- Factored loa=2000 kNBearing capacity of concrete=0.45×20=9

Q: 8. (a) How would you judge the quality of an oil paint? (b) What is distempering? How is it done? 9.…

A: Note- Hi! Thank you for the question, As per the honor code, we are allowed to answer three…

Q: In the propped beam shown, Solve for the following a. wall moment b. maximum deflection note : use…

Q: A 15 kW pump with 80 efficiency is discharging oil of specific gravity 0.85 to the overhead tank…

Q: Q2/ Given below are ordinates of hydrograph, separate the base flow from direct runoff flow by using…

Concept explainers

Engineering Economics Principles

Engineering economics (engineering economy) is a sub-field of economics to study the use and application of the economic principles in the engineering analysis of decisions along with the systematic evaluation of the advantages of project costs inclusive of engineering design and analysis. It emphasizes microeconomics (a subset of economics) for researching the behavior of people in the decision-making process of assigning and determining multiple alternatives to the usage of some of the restrained resources and merging economic theory and engineering practice in a practical manner. It depicts the logical framework of economics in addition to the analytical application of statistics and mathematics.

Question

100%

Please answer it clearly and don't waste my question,I will vote it up for your effort thank you.

3. A homogeneous bar with a cross-sectional area of 400 mm² is attached to fixed supports as shown in
the figure. It is subjected to lateral forces P, = 20 kN and P2 = 50 kN. Determine the normal stress
developed in segments AB and BC.
Answer: OAB = 80.55 MPa
A
B
P1
P2
0.60 m
1.20 m
0.90 m

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

Two line loads q1 and q2 of infinite lengths are acting on top of an elastic medium, as shown in Figure P8.6. Find the vertical stress increase at A.
I want Normal stress developed in segment AB. A homogeneous bar with a cross-sectional area of 400 mm2 is attached to fixed supports as shown inthe figure. It is subjected to lateral forces P1 = 20 kN and P2 = 50 kN. Determine the normal stressdeveloped in segments AB and BC. Answer: σAB = 80.55 MPa
A moment is exerted on the profile given in the figure to make an angle B with the vertical. Calculate the stress at point B. Given a = 90 mm, b = 60 mm, c = 110 mm, d = 130 mm, Beta = 80 degrees, M = 13 kNm,
Refer to Figure P6.3. Determine the vertical stress increase Δσ at point A with the values q1 = 90 kN/m, q2 = 325 kN/m, x1 = 4 m, x2 = 2.5 m, and z = 3 m.
EB and FG are two planes inside a soil element ABCD as shown in Figure 10.50. Stress conditions on the two planes are Plane EB: EB = 25 kN/m2; EB = +10 kN/m2 Plane FG: FG = 10 kN/m2; FG = 5 kN/m2 (Note: Mohrs circle sign conventions for stresses are used above) Given ; = 25, determine: a. The maximum and minimum principal stresses b. The angle between the planes EB and FG c. The external stresses on planes AB and BC that would cause the above internal stresses on planes EB and FG
Determine the average axial tensile stress in the bar of the figure below if P=225 kN and the cross sectional area of the bar is 2500 square mm
A rectangular concrete slab, 3m x 4.5m shown in Figure 05.12, rests on the surface of a soil mass. The load on the slab is 1620 kN.1.) Determine the soil stress below the slab2.) Determine the vertical stress increase at point A3.) Determine the vertical stress increase at point B.
The vertical stress at point P1 due to the point load Q on the ground surface as shown in figure is sigma_{z} According to Boussinesq's equation, the vertical stress at point P2 shown in figure will be
Determine the stress components (σx′ , τx′y′) acting on the inclined plane AB in (Figure 1), where τxy=−38.5MPa. Solve the problem using the method of equilibrium.
Q#5: From the Tri –axial test, determine the effective normal stress on the plane of Maximum shear stress. Explain why the shear failure occurred along the plane with angle 54.73 and not along the plane of maximum shear stress. Take σ’1 = 552, σ’3 = 276, ø’ = 19.45? Find σ’ = ? τf = ? τ: ?
Using the principles of Mohr’s circles for the soil element shown in Figure 10.36, determine the following:a. Maximum and minimum principal stressesb. Normal and shear stresses on plane AB
A soil element is shown in Figure 10.38. Using the pole meathod, determine: a. Maximum and minimum principle stresses. b. Normal and shear stresses on plane AB Solve this problem three ways: first via equations, second via Mohr’s circle and the two-theta method, and third via Mohr’s circle and the origin of planes. All methods should give the same answer.