3.) A steam power plant uses the ideal Reheat-Regenerative Rankine cycle where the steam enters the high-pressure turbine at 4 MPa and 300C. It partially expands to 600 kPa where some steam is extracted for feedwater heating while the rest is reheated to the same temperature. After expanding again, it enters the condenser at 10 kPa. Sketch the schematic diagram and the TS diagram with labeled points, and solve for mass taken for feedwater heating, Qa, Qr, Wt, Wp, Wnet, thermal efficiency, and Steam rate. Neglect the condensate pump work. kJ kg 20.01%, 2667.84 , 1715.88. ,955.97 3.74, 951.96 K , 35.68%, 3.78- kJ kg kg kWh kg kg

3.) A steam power plant uses the ideal Reheat-Regenerative Rankine cycle where the steam enters the high-pressure turbine at 4 MPa and 300C. It partially expands to 600 kPa where some steam is extracted for feedwater heating while the rest is reheated to the same temperature. After expanding again, it enters the condenser at 10 kPa. Sketch the schematic diagram and the TS diagram with labeled points, and solve for mass taken for feedwater heating, Qa, Qr, Wt, Wp, Wnet, thermal efficiency, and Steam rate. Neglect the condensate pump work. kJ kg 20.01%, 2667.84 , 1715.88. ,955.97 3.74, 951.96 K , 35.68%, 3.78- kJ kg kg kWh kg kg

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A steam power plant operates on the simple ideal Rankine cycle. The steam enters the turbine at 4 MPa and 500°C and is condensed in the condenser at a temperature of 40°C. draw and label the schematic diagram and the pV and TS planes. (a) Show the cycle on a T-s diagram. If the mass flow rate is 10 kg/s, determine (b) the thermal efficiency of the cycle (c) the net power output in kW.
A power plant is to be operated on an ideal Rankine cycle with the superheatedsteam exiting the boiler at 4 MPa and 500°C. Calculate the thermal efficiencyand the quality at the turbine outlet if the condenser pressure is (a) 20 kPa,(b) 10 kPa, and (c) 8 kPa.
Consider a steam power plant that operates on a reheat Rankine cycle. The plant maintains the boiler at 7 MPa, the reheat section at 1200 kPa, and the condenser at 10 kPa. The mixture quality at the exit of both turbines is 93 percent. Assume the isentropic efficiency for the Pump, high-pressure turbine, and low-pressure turbine as 80%, 75%, and 75%, respectively. Determine the (a) temperature at the inlet of each turbine in kelvin and (b) the cycle thermal efficiency
Steam enters the turbine of a power plant operating on the Rankine cycle at 3300 kPa and exhausts at 50 kPa. To show the effect of superheating on the performance of the cycle, calculate the thermal efficiency of the cycle and the quality of the exhaust steam from the turbine for turbine-inlet steam temperatures of 450, 500, 5500C.
A simple power plant utilizing the Rankine Cycle operates with an inlet boiler pressureof 5 MPa and an inlet condenser pressure of 300 kPa. Because of frictional effects, thepressure of the water drops 0.3 MPa in the boiler and 3 kPa in the condenser. Thetemperature of the steam as it enters the turbine is 700 °C. The adiabatic efficiency ofthe pump and of the turbine are 83 percent and 88 percent, respectively. The pumpand the turbine are adiabatic, and the water enters the pump as saturated liquid. It canbe assumed that heat transfer to the water in the boiler is from a reservoir at 1500 K,and the environment is at 25 °C.Determine the thermal efficiency of the cycle and compare it with the thermal efficiencyof (a) a Carnot cycle, and (b) the ideal Rankine Cycle. Specify the amount of entropygenerated in each step of the real cycle
Consider a steam power plant that operates on the ideal reheat Rankine cycle. The plant maintains the boiler at 5000 kPa, the reheat section at 1200 kPa, and the condenser at 20 kPa. The mixture quality at the exit of both turbines is 96 percent. Determine the temperature at the inlet of each turbine and the cycle's thermal efficiency. Answers: 327°C, 481°C, 35.0 percent.
An ideal reheat 210 MW Rankine cycle with water as the working fluid operates the boiler at 15 MPa, the reheater at 2 MPa, and the condenser at 10 kPa. The temperature is 500 0C at the entrance of the high-pressure and low-pressure turbines. Determine (a) the quality of the steam at the low-pressure turbine exit, (b) the thermal efficiency of this system, and (c) the rate of heat transfer in the reheater.
Scenario (1)The first steam power plant operates on an ideal reheat Rankine cycle. Steam enters the first turbine at 8 MPa and 500 C and leaves at 3 MPa. Steam is then reheated at a constant pressure to 500 C before it expands to 20 kPa in the low-pressure turbine. Assuming that heat is being added to the boiler from a high temperature source at 1800 K and the condenser is transferring heat to a temperature sink at 300 K. Task 1 Investigate the effect of changing turbine efficiency on the overall thermal efficiency of the thermodynamic cycle. (Hint: You will assume different values for the isentropic turbine efficiency such as: 70%, 80%, 90%, 95%, and 100%, then observe how it will change the thermal efficiency of the cycle). Representing the results in a plot is recommended.
Consider a steam power plant operating on the ideal regenerative Rankine cycle with one open feedwater heater. Steam enters the turbine at 14 MPa and 600 degree celsius and is condensed in the condenser at a pressure of 15kPa. Some steam leaves the turbine at a pressure of 1.5 MPa andenters the open feedwater heater. For every kg of steam, determine the following: (a) thefraction of steam extracted from the turbine, (b) the turbine work (c) Pump work, (d) Heatadded, (e) Heat rejected, and (f) the thermal efficiency of the cycle.
Consider a steam power plant operating on the simple ideal Rankine cycle. Steam enters the turbine at 3 MPa and 350°C and is condensed in the condenser at a pressure of 75 kPa. Determine the thermal efficiency of this cycle
A simple rankine ideal cycle with water as the working fluid. Twenty kilograms of steam enters the turbine at 7.356 MPa and 500.356 oC and is cooled in the condenser at a pressure of 10.356 KPa by running cooling water from a lake through the tubes of the condenser at rate of 2000 kg. Show the T-s diagram and schematic of simple rankine cycle. For cycle determin (a) the turbine work, (b) the heat added, (c) the temperature rise of the cooling water, (d) the thermal efficiency of the cycle. For engine, determine (e) the heat added, (f) the thermal efficiency of the engine, and (g) Draw the T-s and schematic diagram.
The turbine of a steam power plant operating on a simple ideal Rankine cycle produces 500 kW of power when the boiler is operated at 3.5 MPa, the condenser at 40 kPa, and the temperature at the turbine entrance is 650oC. Determine: (a)the rate of heat supply in the boiler, (b)the rate of heat rejection in the condenser, and (c)the thermal efficiency of the cycle. Answers: (a) 1458 kW, (b) 958 kW, (c) 0.343