3. An amount of glycerin has a volume of 1.0 m3 when the pressure is 120 kPa. If the pressure is increased to 400 kPa, determine the change on volume if the bulk modulus of glycerin is equal to E, = 4.52 GN/m2

3. An amount of glycerin has a volume of 1.0 m3 when the pressure is 120 kPa. If the pressure is increased to 400 kPa, determine the change on volume if the bulk modulus of glycerin is equal to E, = 4.52 GN/m2

Engineering Fundamentals: An Introduction to Engineering (MindTap Course List)

5th Edition

ISBN:9781305084766

Author:Saeed Moaveni

Publisher:Saeed Moaveni

Chapter10: Force And Force-related Variables In Engineering

Section: Chapter Questions

Problem 26P: SAE 30 oil is contained in a cylinder with inside diameter of 1 in. and length of 1 ft. What is the...

See similar textbooks

Related questions

Q: An iceberg floats in sea water with 14% of its volume projecting above the sea surface. If the…

A: Volume above sea surface = 14% specific weight of sea water = 10400 N/m3 It has been asked in the…

Q: The state of stress in a long dam is as shown in the figure, Determine oz in MPa? [E = 200 Gpa, p =…

A: Given, Property of long dam, Modulus of elasticity=E = 200Gpa μ= 0.3 σx= 200mpa σy= 300mpa

Q: 1 kg of water has a bulk modulus of 2.4 GPa. Determine the percentage reduction in volume if the…

Q: A liquid has an absolute viscosity of 3.2 × 10^-4 Ib-sec/ft?. It weighs 56 Ib/ft³. What are its…

A: kinematic viscosity is ν=μρν=3.2×10-4lb-secft56lbft3ν=5.7143×10-6ft2sec

Q: A cube of material is 4 in. on a side and floats at the interface between kerosene (SG=0.82) and…

Q: The state of stress in a long dam is as shown in the figure, Determine oz in MPa? [E = 200 Gpa, µ =…

Q: 3. An amount of glycerin has a volume of 1.0 m3 when the pressure is 120 kPa. If the pressure is…

A: Hello dear this is the solution of your problem Please refer to the attachment, thanks

Q: c) Illustrate the results of the viscosity test of the above motor oil then fit the viscosity…

A: Step 1

Q: If the pressure at the bottom of an open tank is 686 kPa, find the unit weight (kN/m) of gold in…

A: Given data, a = 6.92 m b = 6.66 m c = 2 m Sw = 1 Sal = 2.70 Sg = ? To find out the unit weight…

Q: From the given figure. From the e-log p plot, two points were given. p1 = 80 kPa e1 = 0.60 p2 = 150…

A: Given, P1=80 kpa ρ1=0.60 P2=150kpa ρ2=0.40To calculate:- Liquid limit ωL=?

Q: Ships and sailing vessels often carry lead ballast in various forms, such as bricks, to keep the…

Q: A material has a dry mass of 115 g, volume in natural state is 55cm3, volume in absolute compact…

A: The values given in the question are as follows Dry mass(md)=115 g Volume in natural state(Vn)=55…

Q: A sample of water contained the following salts in mg/litre. Ca(HCO3)2= 40.5,MgS04 = 30 CaS04 = 34…

Q: A liquid has a specific weight of 41.5 lbs/ft3. How much will a cylinder that measures 18” tall and…

A: The specific weight of liquid = 41.5 lbs/ft3 Height of cylinder = 18" = 1.5 ft Diameter of cylinder…

Q: The bulk modulus of water is 210x10 kN/m². What pressure is required to reduce the volume of water…

Q: The temperature and pressure of nitrogen in a tank are 28deg C and 600 kPa abs, respectively.…

Q: (b) Fill the Principal SI Unit as shown in Table Q1. Table Q1 Unit Meter per second square Quantity…

Q: Calculate the alkalinity (in mg/L as CacO3) of a water containing 80.0 mg/L of bicarbonate, 10.0…

A: Alkanity is defined as ability of ions to neutralise acidic ions or hydrogen ions (H+) ions in…

Q: When a pressure of 20.7 MN/m is applied to 100 litres of a liquid its volume decreases by I litre.…

A: Given data : Initial volume (V)=100 litre Decrease in volume (dV)=1 litre Pressure applied (dP)=20.7…

Q: 80 cm Ø water Wtank+water = 500 kg Wempty = 60 kg 200 cm

Q: Solve the following problem and result is: Specific gravity of the material is : 4.45 Empty weight…

A: The Specific Gravitry is Given As :G=W2-W1(W4-W1)-(W3-W1)Where: W1=Weight of Empty…

Q: For the configuration shown below what must be the value of the specific weight of the unknown…

A: Calculation:Take the reference line as showed in given figure as follows.

Q: A water sample contains the following dissolved ions: [Na+] = 75 mg/l [HCO₂] = 250 mg/1 [CH] = 100…

Q: When a football of 30 cm diameter fell into a water tank, 10% of its volume found under water.…

Q: kinematic viscosity

A: To find: Kinematic viscosity

Q: .) A quart of SAE 30 oil at 68 °F weighs about 1.85 lb. Calculate the oil's specific weight, mass…

Q: 2. A cube of material is 4 in. on a side and floats at the interface between kerosene and water, as…

Q: During the construction of a dam, concrete was poured into a lift of approximately 1.8 m (y1 = 1.8…

A: Solution:

Q: 1. Locate the center of mass of the figure shown below. Where the vertical face has of 30 kg/m^2,…

A: This problem is related to solid mechanics. In this problem given about mass and dimensions of…

Q: A liquid undergoes a pressure change of 6x10^4 N/m^2 and its volume decreased by 0.1 cm^3 resulting…

A: solution Change in pressure dP =6×104 Nm2=6 Ncm2volume decreased dV=-0.1cm3final volume…

Q: The specific weight of glycerin is 1.26 lb/ft3 . Compute its density (kN/m3 ) and specific…

Q: On land, a boulder has a weight of 850 N. When placed in water, it now weighs 541 N. i) Determine…

A: Determine magnitude of bouyant force and volume of boulder

Q: Question 5 In a test to determine the bulk modulus of a liquid it was found that as the absolute…

A: Given data : Initial pressure (P1)=15 psiFinal pressure (P2)=3000 psiInital Volume (V)=10.240…

Q: 17. A liquid has an absolute viscosity of 23 CP. It weighs 8.4 kN/m³. What is its kinematic…

A: As per the guidelines we are supposed to solve only first question for multiple question posted.…

Q: 1. If K = 2.2 GPa is the bulk modulus of elasticity for water, what pressure is required to reduce a…

A: Given data in question Bulk modulus reduction percentage in volume Change in pressure To find out…

Q: Consider the following conditions: Condition I Condition 2 A wooden cube of size 2 m and the 20% of…

A: Given data, Condition - 1 Wooden cube size = 2 m Relative density = 0.5 Condition - 2 20% of the…

Q: • In the piezometers of the figure shown, liqui stands 1.37 m above point M. What is the pressure at…

Q: An oil of density 850 kg/m³ is pumped in a pipe of diameter 20 cm. The discharge is measured as…

A: Given data, Oil density =850 kg/m3diameter= 20 cmdischarge = 0.015 m3/sdrop in pressure= 800 mto…

Q: 1) A liquid has an absolute viscosity of 2.4x10 N-s/m2. It weighs 7.85x103 N/m³. What is its…

Q: From the figure shown, the alcohol surface is subjected to an absolute pressure of 175 kPa. Compute…

A: 1at 7m…

Q: Q. 4. 1 ppm CaC03 equivalent hardness is meant by A : 10 mg CaC03 equiv. Per litre B : 100 mg CaC03…

A: The accumulation of mineral salts like Ca2+, Mg2+, Al3+, Iron, as well as other heavy metals causes…

Q: An amount of glycerin has a volume of 1 m' when the pressure is 120 kpa. If the pressure is…

Q: If 6 m³ of oil weighs 47 kN, calculate its specific weight y, density p, and specific gravity.

A: Specific weight is the weight of sample per unit volume Density is the mass per unit of its volume…

Q: If the pressure at the bottom of an open tank is 593 kPa, find the unit weight (kN/m2) of gold in…

A: In the question, it is mentioned as gold whereas in figure it is mentioned as titanium. Whether it…

Q: A liquid has a dynamic viscosity of 4.8x10* lb-s/ft² and weighs 54 lb/ft³. What is its kinematic…

A: Given:- Dynamic viscosity=4.8×10-4 lb-s/ft2Weight=54 lb/ft3 To find:- From the given question it is…

Q: 1.3 A liquid at 20°C has a relative density of 0.80 and a kinematic viscosity of 2.3 centistoke.…

Q: Specific gravity and viscosity of an oil is S=0.85 and u=0.35 Ns/sq.m respectively. Determine the…

A: specific gravity of oil, S = 0.85 Mass density of oil S ×Mass…

Concept explainers

Braced cuts

The braced cut is a method of providing lateral support to the soil in foundation trenches, to prevent the trenches from deformation by the caving in of soil and resisting it from moving laterally. During shallow excavation in firm soil, generally, slopes are provided to resist the caving in of soil. During shallow excavation in soft soil and deep excavation, the chances of caving in of soil increase. Hence, it becomes necessary to make a provision to resist the deformation of trenches due to caving in of soil. The braced cut is the method used for such conditions. The excavation using braced cuts is a bit uneconomical as compared to the traditional open-cut excavation method but provides better safety than the cut excavation method.

Question

Answer number 3 please..thankss!!

2. What is the mass in kilograms of 5 liters of gasoline (y = 45 "/
3. An amount of glycerin has a volume of 1.0 m3 when the pressure is 120 kPa. If
the pressure is increased to 400 kPa, determine the change on volume if the
bulk modulus of glycerin is equal to E, = 4.52 GN/m2
%3D
4. To what height will water rise in a 3mm-diameter glass tube at 20°C? Assume
Owater = 0.073 and y20 = 9790 N/m³ ?
%3D

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

given data

VIEW

calculation of change in vloume

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

1. The reading of an automobile fuel gage is proportional to the gage pressure at the bottom of the tank. The tank is A deep and is contaminated with B of water. The specific volume of gasoline is 0.00147076 m /kg and that of air is 0.0008313 m³/kg. Unit weight of water is 9790 N/m3 a. Determine the gage reading when the tank is full of gasoline b. How many cm of air remains at the top when the gage indicates full if the tank is A deep and is contaminated with B of water. c. Determine the pressure at the interface of the gasoline and water when the gage indicates full A = First name in inches Vent B = A/10 in inches Air h A Gasoline Pgage Water B
QUESTION 1 Find the pressure in the pipe cortaining gasoline in kPa. Ir the given conditions, cir has a density of 1.1 kg/m Oil SG 0.79 gage =370 kPa Gasoline SG =0.70 Air- 45 cm 50 cm Pipe 22 cm 10 cm Mercury SG = 13.6 Water
Gas flows at a steady rate in a 100-mm diameter pipe that enlarges to a 150- mm diameter pipe. At a certain section of the 100-mm pipe the density of the gas is 200 kg/m³ and the velocity is 20 m/s. At a certain section of the 150- mm pipe the velocity is 14 m/s. Which nearly gives the weight flow rate in N/s in the pipe? O a. 412.5 N/s O b. 125.7 N/s 331.1 N/s O d. 308.2 N/s
AAAAAAAAAAAAAAAAAAAA 2 Pa oil with density 706kgf/" and viscosity 4-7×10 7³9 flows out of storage tank below: Determine the minimum diameter that results in a flow rate of 18 litres per minute. Provide answer in cm H = 1.4m L = 7m
A closed pressurized tank shown below is filled with oil and mercury. Mercury is confined inan internal reservoir inside the closed tank, the height of mercury is 450mm. An openmanometer is placed on the bottom left part of the tank with liquid “X” as its gage liquid , thedeflection from the gage liquid shows 800mm. Determine the following:a) Height of the oil from point A up to point c if height A to C is 5 times the height of y.b) Pressure at point B in kPa. c) Pressure at point C in psi.
H.W2/3.4/Page(91)/ The local atmospheric pressure is 91 kPa. A gauge on an oxygen tank reads a pressure of 250 kPa gauge. What is the pressure in the tank in kPa abs?
The tank contains a liquid having a density of 2.52 slugs/ft^3 10 in 5 ft 10 ft. 7 ft Pliquid 2. 52 slugs/ſt³ %3D a. Determine the unit weight of the liquid when it reaches the indicated level. b. Determine the liquid's weight. Use English units to express your response. c. Assuming no mixing of liquids occur, if glycerin (SG = 1.26) is poured into the tank, will it sink to the bottom, or will it float on the surface of the liquid, or will it be suspended in the liquid?
H.W.1/ Suppose the pressure in a car tire is specified as 3 bar. Find the absolute pressure in units of kPa? H.W2/3.4/Page(91)/ The local atmospheric pressure is 91 kPa. A gauge on an oxygen tank reads a pressure of 250 kPa gauge. What is the pressure in the tank in kPa abs?
An opening of area 0.257 cm2 in an otherwise closed beverage keg is 45.4 cm below the level of the liquid (of density 1.09 g/cm) in the keg. What is the speed of the liquid flowing through the opening if the gauge pressure in the air space above the liquid is (a) zero and (b)0.748 atm? (a) Number i Units (b) Number i Units
Q3: A U-tube containing mercury is used to measure the pressure of an oil of specific gravity 0.82 as in figure 2. Determine (1) Calculate the pressure of the oil, if the difference of mercury level be 400mm What was the application of pascal's law and hydrostatic law for this problem? (ii) ¼ 300 mm Water Water -oil Figure 2 200 mm. 400 mm 400 mm -X -Mercury
There are four liquids that are to be poured in a single vessel that is located in an atmosphere with g = 3.72m/s2. The first liquid is seawater (SG=1.025), the second is kerosene (ρ=1.591 slugs/ft3), the third is castor oil (SG=0.959), and the last liquid is liquid butane (unit weight = 2235.72N/m3 @ g=3.72m/s2). (a)Determine the density of seawater, the specific gravity of kerosene, the unit weight of castor oil and the density of liquid butane expressing all your answers in SI Units. (b) Illustrate the order of the liquids from the top-to-bottom of the vessel?
Obtain a graduated beaker and accurate scale from a chemistry lab and measure the density of the following liquids:a. a cooking oilb. SAE 10W-40 engine oilc. waterd. milke. ethylene glycol (antifreeze)Express your findings in kg/m3 . Also determine the specific gravity of each liquid.