3. Calculate the value ofZ, in the circuit in order for ZL to receive maximum average power. What is the maximum average power received by ZĽ? -j10 2 30 Ω ZL 5/90° A 40 2 j202 ele

Q: The average power absorbed by an impedance of Z= 4-j3 ohms if supplied by the source shown in the…

A: Given :   In the question they have mentioned a voltage waveform, from the given voltage waveform we…

Q: 4. Find I, and the average power absorbed by the impedance 1- j20. 22 j1 2 ll-w 4 2 8/90° A (4 js 2…

A:

Q: v = 141.4 sin (@ot + 30°) V and i= 11.31 cos (@t - 30° ) find for each (a) the maximum value, (b)…

A: Since you have asked multiple questions in a single request, we will be answering only the 1st…

Q: Consider the following circuit, supplied by a 10VRMS voltage source with a 0° phase shift (i.e.…

A: Consider the following circuit, supplied by a 10VRMS voltage source with a 0° phase shift (i.e.…

Q: b) Find the maximum average power. j18 2 20 2 j60 480 /0° V (rms) j20 Q Solution:

A:

Q: A 50 ΩΩ transmission line is matched with a load ZlZl. If the frequency of operation is 100MHz100MHz…

A: When the impedance of the load is same as the characteristic impedance of the transmission line ,…

Q: a) Determine the load impedance for the circuit that will result in maximum average power being…

A:

Q: Estimate the power factor and the apparent power of a load whose impedance is Z = 60 + j40 Ω when…

A: The solution can be achieved as follows.

Q: Given that voltage is 450cos(wt + 6) V and current is 40cos(wt + 2) A (phase angles in radians). (A)…

A: The solution is given below

Q: 120 V rms Z = 10 +j12 2 60 Hz What is the value of the capacitance that will give unity power…

A:

Q: The voltage at the sending side (source) of a transmission line is 1 KV (Vs = 1 KV). The voltage at…

A:

Q: 17 The voltage a cross a load impedance is V = 12270° V and the current through it is I = 32-20° A…

A:

Q: 10. Consider the circuit shown below (the voltage phasors are expressed in RMS) A THD 54n AA 260 240…

A:

Q: Rine jXline + VL |L1 L2 L1: Absorbs an average power of 12kW at a leading power factor of 0.9. L2 :…

A: In this question we need to find a average power consumed by the line.

Q: 4. From the following circuit calculate the total: (a) apparent power, (b) reactive power and (c)…

A: The given circuit is a simple parallel circuit in which we will first calculate value of I1 and I2.…

Q: Q3 (a) In Figure Q3(a), the load impedance, Zi is adjusted until it absorbs the maximum average…

A:

Q: Find average power absorbed by impedance Z=30-70j ohm when a voltage 120V is applied across it. А…

A: In this question we will find average absorbed power by impedance ..

Q: Calculate the maximum average power that Z_L can absorb. Z_L= 3.32+j1.07 Ohms -j4 2 j1Ω ll 5Ω ) 4A 8…

A: Thevenin's theorem states that any network containing linear and bidirectional elements and…

Q: 10 Ω 8Ω 40/0° V rms j4 Ω -6 Ω

A:

Q: Q1/ Find the RMS value of lo in the unbalanced three-phase circuit. 0.4 0 a 1.60 j40 A 780 j54 N…

A: In the circuit 3 phase balance supply to unbalanced load.  Find the rms current of the Io

Q: decimal places and box thefinal answer. The instantaneous voltage and current for an ac circuit are…

A: We need to find out impedance and power for given current and voltage

Q: Compute for the value of the impedance load that will absorb a maximum average power. 10Ω j15 N ell…

A: To absorb maximum average power first we have to calculate Thevenin's impedance across the load by…

Q: Determine the impedance ZL for maximum average power transfer and the value of the maximum average…

A:

Q: 2. Using the Illustration below. Compute the total impedance (Z), the total current (1), the voltage…

A:

Q: 120 V rms +. Z= 10 +j12 2 60 Hz What is the power factor if we change the nature of the impedance…

A: Option - A.   (Answer)

Q: Compose the mesh equations. 10 Q j10 O j10 2 ll ell 10 V [11] [12] :-10 2 sine sine

A:

Q: Find ZL. And Find the maximum average power transferred to the load. L=j1Ω Both R=7Ω

A: Above given circuit is a R-L circuit. In ac circuits having energy storage elements like L and C…

Q: the average power loss and power factor for each of the circuits whose input cate if the power…

A:

Q: Find the average ZL for maximum average power transfer. Find the value of the maximum average power…

A:

Q: 2. The instantaneous voltage and current equations of an ac circuit are v(t)= 200 sin377t V and…

A: Given: vt=200sin377t Vit=8sin377t-30° A

Q: Calculate the power factor of the entire circuit of Fig. 11.19 as seen by the source. What is the…

A:

Q: Problem 7.3 For the power system shown, find: a) the average power, b) the reactive power, c) the…

A:

Q: Find Z₁ for maximum average power transfer and the maximum average power transferred. 1 Ω 1Ω…

A:

Q: Calculate the value of ZL in the circuit in order for ZL to receive maximum average power. What is…

A: Maximum power transfer theorem says that to obtain maximum power from a network, the resistance of…

Q: A=4, b=7 xlt) = a.Coslb.t) y (t)= X(t) + X(-t) %3D a) y(t) RMS value? b) calculate the phase

A:

Q: ww ell 82 10/0° V -j62 Determine the load impedance ZL that maximizes the average power drawn from…

A: For dc source the maximum power transfer states that maximum power is abstract by load resistance if…

Q: 8Ω Problem 3) Find the average power absorbed in all components in the AC circuit shown. 4Ωζ 620° V…

A: Let V be the node voltage. Write the KCL equation.

Q: A 50 2 transmission line is matched with a load Z1. If the frequency of operation is 100MHZ and the…

A: Here they have mentioned the transmission line with characteristic impedance    ZO = 50 Ohm. Given…

Q: Determine the average power delivered to each of the boxed impedances in the circuit below if V, =…

A: Power in AC circuits has two components. Here, S is called apparent power (in VA’s), P is termed as…

Q: Compute for the value of the impedance load that will absorb a maximum average power. 10 Ω j15 N ell…

A:

Q: 1. v(t) = 150 cos(50t) V and i(t) = -20 sin (50t – 30) Calculate the following d. Instantaneous…

A:

Q: a) What load impedance ZL will draw the maximum average power from the source shown in the following…

A: The given AC circuit is,

Q: The voltage across and the current through a load are expressed as follows v(t) = -170 sin 377t - V…

A: The voltage is given as: Using the trigonometric relation in the above expression, it can be…

Q: 0.09 0 j0 25 1 24 kW 0.85 pf lagging 36 kW 0.78 pf lagging V 0 V ms For the three phase circuit…

A:

Q: A load Z draws 19 KVA at a power factor of 0.8 lagging from a 124 V rms sinusoidal source. Answer…

A:

Q: VI) For the circuit shown, answer the questions from 15-19. The load ZL = 8+j6 ohms, and the source…

A: The solution is given below

Q: 80 -j2 n 4<0° A -j3 0 50 j20 10<30° V

A:

Q: Find Z1, for maximum average power transfer and the maximum average power transferred. j22 -j4N 2Ω…

A:

Q: Given the following voltage and current: i(t) = 5 sin(377t - 40°) A v(t) = 10 cos(377t + 90°) V…

A: Given it =5 sin377t-40° Avt =10 cos377t+90° V