Answered: A=4, b=7 xlt) = a.Coslb.t) y (t)= X(t)…

Engineering

Electrical Engineering

A=4, b=7 xlt) = a.Coslb.t) y (t)= X(t) + X(-t) %3D a) y(t) RMS value? b) calculate the phase

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter2: Fundamentals

Section: Chapter Questions

Problem 2.11MCQ: The power factor for an inductive circuit (R-L load), in which the current lags the voltage, is said...

See similar textbooks

Related questions

Q: 0.038 +/0.072 f/phase. Calculate the line-to-line source volt- age magnitude required so that the…

A: For Star connection, Line voltage, VL = 3 * Phase voltage, VPh Line current, IL = Phase current,…

Q: Calculate the Apparent power (complex in VA), real power (real part in W) and reactive power…

A: Let the current flowing through 40 Ω from top node to bottom node is I1 and the current…

Q: v = 141.4 sin (@ot + 30°) V and i= 11.31 cos (@t - 30° ) find for each (a) the maximum value, (b)…

A: Since you have asked multiple questions in a single request, we will be answering only the 1st…

Q: For the admittance locus diagram shown below: find the value of each element in the circuit if w=377…

A: Equivalent electrical diagram: For first branch θ=tan-1XCR⇒-60°XCR=-3and because AB=BCso, XL=RWe…

Q: 100 H(jm) (fo) (Jw2 + 1)

A: Solution- H(jW) = 100jw2jw2+1 The corner frequencies, Wc1 =0 rad/secWc2 =1 rad/sec The initial…

Q: Find the rms value of each of the followingperiodic currents:a. i(t) = cos 377t + cos 377t Ab. i(t)…

A: The RMS value to the combination of DC and sinusoidal sources of the same frequency is given by the…

Q: 0.038 +0.072 f/phase. Calculate the line-to-line source volt- age magnitude required so that the…

A: In star connection, Line voltage, VL = 3 * Phase voltage, VPh Line current, IL = Phase current, IPh…

Q: n the figure given below, the rms value of the line voltage is 238 V. Find the average power…

Q: (b) A three-phase system has voltages expressed in time domain as follows: Von (t) = 110cos(wt +…

A: If time domain signal is of the form Vm cos(wt+phi) than phasor representation of the signal is Vm…

Q: The in-phase sinusoidal currents in the parallel branches of a circuit have the following equation:…

A: Given , i1=17 sin 377t Amp i2=22.6 sin 377tAmp

Q: Consider the following sinusoids, i¬(t) = -4 sin (377t+25°), and i2(t) = 5 cos (377t-40°) Analyze…

A: The circuit this is excited the use of alternating supply is referred to as an AC Circuit. The…

Q: Perform phasor analysis to the circuit shown to evaluate the total complex power (S) absorbed by the…

A: In this question, we need to determine the across the load 40+30j i. average power (P), ii. reactive…

Q: 1. a) Find the rms magnitude and the phase angle of ICA in the circuit shown. 2. b) What percent of…

A: (a) The given load is connected as a delta load. Convert it into a star connected load.

Q: Using rms values to represent their magnitudes, the voltage across and the current into a load are-…

A: We are authorized to answer one question at a time since you have not mentioned which question you…

Q: Given the following equation i = -4 sin(377t + 65°) and e = 5 cos(377t + 190°). Draw the phasor…

A: The solution is given below .

Q: 17 The voltage a cross a load impedance is V = 12270° V and the current through it is I = 32-20° A…

Q: 12V 2012 4052 * 50Ω www – 10Ω 30Ω

Q: (d) Calculate the steady-state current i, by using phasor method. (e) Calculate the voltage across…

A: In this question, We need to determine the current I1 as shown in the circuit. I= V/Z Voltage V=…

Q: i) The maximum and effective (rms) values of v(wt), vi(wt) and i(wt). ii) Write the waveform…

Q: 3. Calculate the value ofZ, in the circuit in order for ZL to receive maximum average power. What is…

Q: 7. In a balanced star-star 3-phase system the RMS line voltage is 230 V. The average power…

A: Since it is balanced 3 phase circuit Calculations and per phase analysis is straight forward

Q: 1. The single phase ac voltage source is v = 141.4cos(377t)V, the load can be modeled as a 16mH…

A: Given, Single phase AC voltage source is , V = 141.4 cos(377t)V by comparing it with standard…

Q: Q1/ Find the RMS value of lo in the unbalanced three-phase circuit. 0.4 0 a 1.60 j40 A 780 j54 N…

A: In the circuit 3 phase balance supply to unbalanced load. Find the rms current of the Io

Q: (10) 8. What is the total apparent power in a balanced c 480 Vms and the load impedance for each…

Q: Q1) The apparent power entering a certain load Z is 250 VA at a power factor of 0.8 leading. If the…

Q: 1. The single phase ac voltage source is v = 141.4cos(377t)V, the load can be modeled as a 16mH…

A: In the question, Voltage given v=141.1cos(377t)V Resistance R=8 ohm inductance L= 16mH…

Q: 4. For the netwoYk Shown below sketch vo and determine Vor 2k2 12oyc'rms)

Q: the equationof alternating voltage is given by v=325.22 sin314t. find(i) RMS value (ii) frequency…

Q: The in-phase sinusoidal currents in the parallel branches odd a circuit have the following…

A: When impedance is connected in parallel then the voltage across the impedance remains the same but…

Q: 2. The instantaneous voltage and current equations of an ac circuit are v(t)= 200 sin377t V and…

A: Given: vt=200sin377t Vit=8sin377t-30° A

Q: The instantaneous voltage across a circuit element is v(t) - 359.3 sin(wt + 15°) volts, and the…

Q: Using rms values to represent their magnitudes, the voltage across and the current into a load are…

A: We’ll answer the first question since the exact one wasn’t specified. Please submit a new question…

Q: Q3) Determine the value of impedance Zo for transferring the maximum power. Calculate the average…

Q: Q2) Determine the value of impedance Zo for transferring the maximum power. Calculate the average…

A: Given

Q: The apparent power entering a certain load Z is 250 VA at a power factor of 0.8 leading. Q1) If the…

A: (a): The RMS current is:S=VrmsIrmsIrms=SVrmsIrms=250125Irms=2A (b): The power factor angle is:…

Q: 1.7 For each of the following RMS cosine referenced phasors write the corre- sponding signal as a…

A: (a) Expression of voltage is given Frequency is given f= 133 Hz Therefore, time period will be,

Q: Find the RMS value of the waveform depicted below. Given A = 9, a = 2, b = 8, and T = 13 %D

Q: i, = 3 sin(377t + 60°) R1.2 N XL 1.20 Ω Χ. 20 Xc

Q: A a 10+ j102 Va = 200 Z0°V, rms 10+ j10Q 10+ j102 n bB b V. В B.

Q: 4.For the following voltage and current phasors, calculate the complex power, apparent power, real…

Q: find (Phase Voltage Va Vb Vc), (line voltage Vab Vbc Vca), (laA IbB IcC), (Total Apparent Power: S),…

Q: 10. Consider the circuit shown below (the voltage phasors are expressed in RMS) A THD 40 a)…

A: Fig: Given balanced three phase power system although impedance of each…

Q: Calculate the average power of an impedance with the following voltage and current. “<” is the…

A: A simple problem based on network analysis. Solved the question in detail. Have a look at the…

Q: Q3. For the circuit shown below, sketch the current waveforms iş and io and determine the Average…

A: The given circuit is a half controlled rectifier bridge with a resistive load. In the first half…

Q: The voltages across two series-connected circuit elements are e1 = -20 sin (ωt - 2π/7) V and e2 = 12…

A: It is given that: e1=-20 sinωt-2π7 Ve2=12 cosωt+π4 V

Q: A single-phase load draws 10 KVAR at a power factor of 0.75 lagging from a 240V rms sinusoidal…

A: Given, A single phase load has following specifications, Reactive power, Q=10 kVAR. Supply, Vrms=240…

Q: A three-phase 2400 V RMS supply feeds a load of 300 kVA, FP = 0.8 delayed in parallel with another…

A: Electrical circuits can be AC or DC. AC quantities have magnitudes as well as frequency. The supply…

Q: calculate the current (I) flows for each passive element in polar form. compute the average power…

A: given: source current =7sin(377t+70) resistance ,R=20 ohm inductance,L=180mH capacitance ,C=85micro…

Q: i) The maximum and effective (rms) values of v(wt), vi(wt) and i(wt). i- ii) Write the waveform…

Q: Find the RMS(effective) value of the current whose graph is given on the side. i (A) 3- 2+ 1 t (s)…

Concept explainers

Digital Integrated Circuit Design

Digital IC design is a procedural interaction that involves converting determinations and highlights into computerized blocks, which are then further transformed into basic circuits. A significant number of the imperatives related with advanced IC plan come from the foundry cycle and innovative restrictions.

Question

A=4,
b=7
xlt) = a.Coslb.t)
y (t)= X(t) + X(-t)
%3D
a) y(t) RMS value?
b) calculate the phase

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

P-channel Metal-Oxide Semiconductor (PMOS), N-channel Metal-Oxide Semiconductor (NMOS), and Complementary Metal-Oxide Semiconductor (CMOS)

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

The average value of a double-frequency sinusoid, sin2(t+), is given by (a) 1 (b) (c) Zero
The instantaneous power absorbed by the load in a single-phase ac circuit, for a general R LC load under sinusoidal-steady-state excitation. is (a) Nonzero constant (b) Zero (c) Containing double-frequency components
If the rms phasor voltage is given as V angle= 60-degree, then how v(t) can be written.
A 60 Hz sinusoidal voltage v = 141sinwt is applied to a series RL circuit. The values of the resistance and the inductance are 3 ohms and 0.016 henry respectively. a) Compute the rms value of the current and its phase angle with respect to the voltage. b) write the expression of the instantaneous current.
A 60 Hz sinusoidal voltage v = 141sinwt is applied to a series RL circuit. The values of the resistance and the inductance are 3 ohms and 0.016 henry respectively. a) Compute the rms value of the current and its phase angle with respect to the voltage.b) write the expression of the instantaneous current.
Use 3 decimal places and box thefinal answer. The instantaneous voltage and current for an ac circuit are v=155.6 sin 377t V and i=7.07 sin (317t - 30degrees) A. Determine the following: a) Impedance of the series circuit b) the real or true power in watts c) reactive power in vars d) apparent power in va
Two units, connected in parallel, are energized by an a-c source. If the component currents are 15 and 19 amp, respectively, calculate the corresponding sinusoidal waves are out of phase by 60 electrical degrees, calculate the rms value of the total current.
Given below are Za=Zb=Zc=(25+j5) Ω : Calculate the total average, reactive and complex powers?
The voltages across two series-connected circuit elements are e1 = -20 sin (ωt - 2π/7) V and e2 = 12 cos (ωt + π/4) V. What is the rms value of the applied voltage? Also determine the phase angle of this voltage with respect to e1
Determine the time-domain expressions for the line-to-line voltages vAB, vBC, and vCA. Please report your answer so the magnitude is positive and all angles are in the range of negative 180 degrees to positive 180 degrees
The impedance ZL in the circuit is adjusted for maximum average power transfer to ZL. The internal impedance of the sinusoidal voltage source is 4+j7 Ω. 1. a) What is the maximum average power delivered to ZL?2. b) What percentage of the average power delivered to the lineartransformer is delivered to ZL?
An alternating voltage is given by v = 40 sin (200πt – 0.5) volts. Find (a) the amplitude, (b) the peak-to-peak value, (c) the r.m.s. value, (d) the periodic time, (e) the frequency, and (f) the phase angle (in degrees and minutes) relative to 40 sin 200πt. Note: Please do not handwriting