3. Determine the force F required to hold the gate shut as shown in the illustration.

Q: 13-45 A garden hose with its nozzle closed has a tiny hole. A fine stream of water shoots from the h...

A: GIVEN DATA- Rise of water 10m We have to calculate Pressure

Q: The Rexroth simulators have the following component specifications: Double acting cylinders with pis...

A: Given : Dp = 25 mm = 2.5 cm Dr = 16 mm = 1.6 cm Q = 8 L/min = 133.33 cm3/s To find : Theoretical rod...

Q: 1. The four sides of a square plate of side 12 cm, made of homogeneous material, are kept at constan...

A:

Q: 8. What is the pressure at the center of the pipe B? The inclined tube makes an angle 36.9° to the h...

A:

Q: A cable of 90 mm long must be able to support a load of 45,000 N without yielding. Given the followi...

A:

Q: A long and slender shaft of diameter 2R and length L1 + L2 is insulated over length L1 and produces ...

A: Assumptions taken: Steady state condition i.e. temperature is not the function of time. Heat genera...

Q: While the pressure remains constant at 698.5 kPa the volume of the system of air changes from 0.57 c...

A:

Q: In onder for an oject to oll smoothly (with comtant angular acceleration) downaramp, itust have eith...

A:

Q: Force P is applied as shown on the 13.5 mm thick plate. P = 100 kN. Holes are oversized causing all ...

A:

Q: h air. What is the pressure exerted by the air o

A: To find Exerted pressure.

Q: The leading edge of a supersonic wing is wedge shaped, with a total included angle of 10°. (See Figu...

A:

Q: A material is required as heating elements for an electrical resistance furnace for heat treating st...

A:    The phenomenon of joule heating is used to create heat in resistive heating components. Due to th...

Q: Water flows to a pump at 100 psig and the pump supplies 100 feet of head pressure. If piping losses ...

A:

Q: You can write in one paragraph about the importance of MLC 2006 to active seafarers. 2. Make a table...

A: MLC stands for the maritime labor convention of 2006. Its basic aim is to provide the right to work ...

Q: 1. Each of the two sides of a hand-operated toaster can be operated independently of the other. A sp...

A: Action CHARTS: MAN AND MACHINE CHARTS IENG 301 FUNDAMENTALS OF WORK STUDY AND ERGONOMICS Action CHAR...

Q: The rigid bar ABC is supported by a pin at B and two vertical steel rods. Initially the bar is horiz...

A:

Q: Water flows to a pump at 100 psig and the pump supplies 100 feet of head pressure. If piping losses ...

A: Pressure inlet to pump, P1=100 psig=100*144 lb/ft2Pump head, Hp=100 ft

Q: 14.12) FOR THE GIVEN STATE OF STRESS, DETERMINE (A) THE ORIENTATION OF THE PLANES OF MAXIMUM IN-PLAN...

A: Given   Stress, σ1=69 MPa             σ2=13.8 MPa Shear stress = 20.7 Mpa Find   Angle   Maximum she...

Q: nvestigate with dimensional analysis, is this equation true t = [ 2x / a ]1/2 B. Express...

A:

Q: The air in a theatre room must be 22 °C and the relative humidity 55%. The outdoor temperature is 30...

A: Given: incoming fresh air for one person=25 m3h let density of the air=1.2 kgm3 so mass flow rate fo...

Q: 5. During a test on a boiler the following data were recorded: Pressure = 1.7 MPa Steam temperature ...

A:

Q: 200 mm 150kN 200 mm <422 mme 200 mm

A:

Q: Flywheels A and B are mounted on light coaxial shafts which can be coupled by means of the clutch C,...

A:

Q: tes between the pressur D0°C, determine the thermal efficiency of the cycle, in %.

A: Determine the thermal efficiency of cycle.

Q: find the Y coordinate of the centroid of the composite line shown

A:

Q: gate in an irrigation canal is constructed in the form of a trapezoid 7 m wide at the bottom, 55 m w...

A:

Q: A sharpe-edged orifice has a diameter of 25.4 mm and coefficients of veloc- ity and contraction of 0...

A:

Q: The simple pendulum shown oscillates in the vertical plane (the plane of the figure) as the pendulum...

A:

Q: Compute the elevation considering the atmosphere as a static fluid which has a final value of 8.43ps...

A: Atmospheric pressure: Air pressure, otherwise called barometric tension (after the indicator), is th...

Q: Use the following information for a dual cycle internal combustion engine and find a) the state para...

A: Given dataP1 = 1 barT1 = 300 KrV = 12.7, rP = P3/P2= 1.4, rc = 1.6the working fluid is air   cv = 0....

Q: The crank AB is rotating with a constant angular velocity of 4 rad/s. Determine the angular velocity...

A:

Q: Required information A brittle material has the properties Sut = 30 kpsi and Suc= 90 kpsi. Using the...

A:

Q: When subjected to a compressive load, the length of the rod is 199,6 mm, and its diameter is 10 mm. ...

A: GIVEN DATA-  Final length of the rod is 199.6 m Intial Length 200mm Diameter d=10mm E=70GPa  

Q: В. ЗР (KN) P (kN) 3m 1m 2m 1m

A:

Q: A uniform horizontal beam with a length of 3.00 m and a weight of 40 N is attached to a wall by a pi...

A:

Q: What is the y coordinate of the centroid of the object shown?

A: Determine the centroid

Q: radius r

A: determine the radious.

Q: 3 m/s. A 20 ton railway wagon is coupled to three stationary railway wagons of the same type with v ...

A:

Q: Determine the Degree of freedom for following PLANAR Linkage:

A: Determine the Degree of freedom.

Q: 6.8-3 An IPN 240 steel beam has the cross section shown in the figure. The dimensions are b = 106 mm...

A: Symmetric section τmax  is at neutral axis-

Q: Flywheels A and B are mounted on light coaxial shafts which can be coupled by means of the clutch C,...

A:

Q: 7.3 Two identical chairs, each weighing 14 lb, are stacked as shown. The center of gravity of each c...

A: Given Data The weight of each chair is: 14 lb The coefficient of static friction at B is: 0.2 The c...

Q: A rotary air compressor working between ar has internal and external diameter oj mm and 600 mm respe...

A:

Q: 5. A mass m is attached to both a spring (with given spring constant k) and a dashpot (with damping ...

A: Given : m = 3 c = 30 k = 63 x0 = 2 v0 = 2 To find : Function x(t)

Q: Q10b. Determine the force in member AE. The length of members AB, AE and ED are each 4 m long as sho...

A:

Q: I need only a) part Q2a)Forces 30 kN ,20 kN,25 kN and 100 kN are respectively directed through the p...

A: GivenF1=30kNF2=20kNF3=25kNF4=100kNA2,1,5B3,-1,4C-3,-2,1D4,1,-2

Q: 3. Helium enters an adiabatic 100-mm-diameter pipe steadily, with a velocity of 75 m/s. At the pipe ...

A: GIVEN DATA- D=100mm V=75m/s P1=200KPa T1=20'C P2=180KPa T2=18'C  

Q: find the x coordinate of the centroid of the composite line shown

A:

Q: Explain why managers use marketing dashboards and marketing metrics.

A: A method used by the company to promote their product on a large scale so that the sales of the comp...

Q: Consider an ideal SPRING-MASS SYSTEM with a block of mass m attached to a movable end of a horizonta...

A: Given data Spring-mass system with a block of mass m attached.Spring constant = k It undergoes simpl...

Axial Load

When a bar of the uniform cross-section is acted by a load, such that the load acts along the longitudinal axis of the bar, such kinds of loadings are known as axial loadings. In general terms, a load is an external force acting on a component. An axial load acts perpendicular to the geometric cross-section of the component. Based on the direction of the application of the load, an axial load can be tensile or compressive. The analysis of bodies under the action of axial loads is generally studied under the branch of mechanics, known as statics.