The Rexroth simulators have the following component specifications: Double acting cylinders with piston diameters of 25-mm and rod diameters of 16-mm. Cylinder stroke of 40-cm for the large cylinder and 20-cm for the small cylinder(s). Pump rated output of 8 liters/minute. Maximum cylinder pressure of 105 bar (10500 kPa). Calculate the following based on the above system specifications. Refer to the formula sheet attached to this lab: a. Piston area [AP] and rod area [AR] in units of m2. 2. Ap = AR x De = x 0.025 x 0-016? = 0.00049 m? 0.00020 mR b. Maximum cylinder force in extension [FE], retraction [FR] and regeneration [Fregen]: C. Theoretical rod speed [cm/sec] in extension [VE], retraction [VR] and regeneration [Vregen]:

The Rexroth simulators have the following component specifications: Double acting cylinders with piston diameters of 25-mm and rod diameters of 16-mm. Cylinder stroke of 40-cm for the large cylinder and 20-cm for the small cylinder(s). Pump rated output of 8 liters/minute. Maximum cylinder pressure of 105 bar (10500 kPa). Calculate the following based on the above system specifications. Refer to the formula sheet attached to this lab: a. Piston area [AP] and rod area [AR] in units of m2. 2. Ap = AR x De = x 0.025 x 0-016? = 0.00049 m? 0.00020 mR b. Maximum cylinder force in extension [FE], retraction [FR] and regeneration [Fregen]: C. Theoretical rod speed [cm/sec] in extension [VE], retraction [VR] and regeneration [Vregen]:

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Completely solve and box the final answers. Write legibly 9. A blower with the inlet open to the atmosphere delivers 250 cubic meters per minute of air at a pressure of 2.50 cm of water gage through a duct 25 cm in diameter, the manometer being attached to the discharge duct at the blower. Air temperature is 25 degrees C and the barometer pressure reads 1.025 bar. Calculate the required motor rating in KW if the blower efficiency is 92.5%
Pi constant to be used: 3.14159 Capillary tube: radius = 0.02 cm; length = 9 cm; pressure = 0.7 mmHg Liquid sample: density = 4 ml; time of flow = 4.5 seconds Determine (a) pressure in MKS unit, (b) pressure in CGS unit, (c) the viscosity of the liquid, (d) If the weight was given as 8.5 grams, what will be the density of the liquid? (e) the kinematic viscosity of the liquid? (f) and the fluidity of the liquid?
which equation is used if the system underdamped. can you pls share the whole eqn
Hi please help me answer this with drawing, thank you. Plot a displacement diagram for a body that is to rise and fall as follows; rise 1 in. in 4 seconds with uniform acceleration, rise 1 in. in 4 sec. with uniform retardation, rest 6 seconds, fall 1 ¼ in. in 6 sec with harmonic motion, rise ½ in. in 3 sec with uniform velocity, fall 1 ¼ in. at once, and rest 4 sec.. Plot displacement as ordinates full size and the time as abscissas to a scale of 1 in. = 4 sec.
Solve this problem in static
The image below depicts one section of a cam shaft which opens a valve to release the pressure in the combustion chamber. In order to synchronize the position of the piston and the release of the valve, there is a sensor that measures the position of the camshaft. The sensor can determine when point a is 0.672 in. to the right of the center of the camshaft and 0.672 in. above the center of the camshaft. In a four stroke engine the crank shaft, which is connected to the pistons, turns twice for every turn of the camshaft. At cruising speed the crank shaft turns at 3,000 rotations per minute (rpm) which means that the camshaft turns at 1,500 rpm or 25 revolutions per second (rps). After 0.825 seconds, where would point a be in relation to the center of the camshaft?* Answer options are: (-0.589,0),(0.116, -0.316), (0,-0.95),(0.86,-0.315),(0.431,0), none of these are correct. Please be sure to show your steps.
given:Q2A=12 INCHESAB= 2FT 4 INCHESBC= 8 INCHESDE = 1 FT 3 INCHESQ7E= 12 INCHESQ5C= 2 FTDF= 2 FTCE = 3FT Ks -> use appropriate scaleKv -> 400ft/min= 1 inchVa= 472 ft/ min ☆ Solve the velocities of F and E by Resolution and Composition☆ pls show the output
SHOW COMPLETE SOLUTION SUBJECT: DYNAMICS , TOPIC: Curvilinear Motion
( STATIC OF RIGID BODIES) Show complete and step by step solution. Limit the answer into 3 decimal points.
Kindly show the COMPLETE STEP-BY-STEP SOLUTION, DON’T DO SHORTCUTS OF SOLUTION, so I can understand the proccess. I will rate you with “LIKE/UPVOTE," if it is COMPLETE STEP-BY-STEP SOLUTION. If it is INCOMPLETE SOLUTION and there are SHORTCUTS OF SOLUTION, I will rate you with “DISLIKE/DOWNVOTE.” Topics we discussed: Statics of Rigid Bodies, Force System of a Force, Moment of a Force, Moment of a Force-Scalar Formulation, Moment of a Force-Vector Formulation, and Principle of Moment. Thank you for your help.
solve by theconcepts of ststics
Each piston of an engine makes a sharp sound every other revolution of the engine. How fast is a race car going if its eight-cylinder engine emits a sound of frequency 750 Hz, given that the engine makes 2000 revolutions per kilometer? At how many revolutions per minute is the engine rotating?